I have a 2016 Mondeo estate will it be the same method ??
@sergiojetro45223 күн бұрын
If I got 190V in circuit? Does this thing could do 230V for my coffemachine?
@GAMECOCKER2916 күн бұрын
Excellent video, well done 👍
@TinkerBod14 күн бұрын
Thank you! Cheers!
@ahmetsavran616819 күн бұрын
Hi I have the acc malfunction come up everytime. How do i reset that fault or what do i need to do. Ford mondeo 2009 titanium
@TinkerBod16 күн бұрын
You need to plug it in. If it does not reset on the ignition, then it's a plug-in job.
@MSPPlumbingHeating29 күн бұрын
My Dad needs to replace his spark lead how do you get the fly wheel off to get to it?
@TinkerBod28 күн бұрын
On this one, you continue to unscrew the flywheel nut and it pulls off the flywheel, on others and later ones you need to remove nut and use an extractor
@kylehasfun3114Ай бұрын
Hey thank you for taking the time to go through all this. What foot pegs did you use? And what 290mm shock did you find to use? I'm going to do the same.
@TinkerBodАй бұрын
Thanks, The foot pegs were off ebay and are for a rip off pw80, baja I think? and are identical to the genuine, be careful as some are chocolate. The shock was also just a random ebay looking at shock lenghs. I cant remember which bike but it definitely was not for a pw80. 👍
@kevinthacker8349Ай бұрын
Thanks,
@TinkerBodАй бұрын
You're welcome!
@jedigeekbikerАй бұрын
This is very good, so the seal will seat the bushing?
@TinkerBodАй бұрын
It will all hold in together 👍
@coulombefrancois5371Ай бұрын
We made it!!! Thank you for this very helpful video. For some reason, the model we have had only 1 bush. The bush was so grasped we had to go to a machine shop to ask for help. The person in charge took the beam and tried on the press. It didn’t go! He had to use a torch to weaken the bush and then on the press it came off😁 We installed 2 bushes, a new pin and the MF is back on the track😁 Thanks again!!
@TinkerBodАй бұрын
Thanks 👍 the single bush is the normal standard unless loaders etc were specified anything applying extra load on the front axle.
@user-hq5rw4nc2gАй бұрын
What is the use of pulling it apart if you can’t find where to buy the gears from??
@TinkerBodАй бұрын
Who said i needed to change the gears?
@user-hq5rw4nc2gАй бұрын
Does not tell us where to buy the bevel gears. I’ve searched high and low and cannot find six tooth splined bevel gears anywhere!!!!
@TinkerBodАй бұрын
Im not your sales advisor.
@user-hq5rw4nc2gАй бұрын
Where did you buy the gears from??
@TinkerBodАй бұрын
I didn't, the bearings had gone as stated
@colinculverwell3252 ай бұрын
My bike didn't have a key for the steering lock. I rode it to a local locksmiths who picked the lock and extracted it in about two minutes. Charged me £6. There was a number on the back of the lock so I was able to order a key and reuse it.
@defendermodsandtravels2 ай бұрын
I have a similar engine (C25) to renovate. You said you found a workshop manual online. Do you remember where you found it? I have been looking without success. Thanks.
@TinkerBod2 ай бұрын
Hi, i paid a donation towards the museum below in the link, they had a very large online library of manuals. I have been to the website just now to check but they have reduced the makes. I would try contacting them and find out what happened to their library 👍 www.internalfire.com/
@hectorlamar8062 ай бұрын
Would have been helpful to show how exactly you pulled it apart.
@1djbecker2 ай бұрын
The bearings are a 'thermal fit'. Use heat to expand the aluminum case. Start with a modest amount, 100C-150C case temperature, but you may need to get to the point where the grease smokes slightly. A heat gun should be sufficient.
@valeryprudnikov50073 ай бұрын
мужик, то что ты делаешь великолепно. все доходчиво, ничего лишнего. спасибо за работу.👍
@TinkerBod3 ай бұрын
Great comment, much appreciated. 👍
@valeryprudnikov50073 ай бұрын
@@TinkerBod благодаря твоему видео, я завтра иду покупать pw80 своему сыну. Это будет его первый байк)
@TinkerBod3 ай бұрын
Great first bike and when the throttle is buried in the ground revving its guts out and it does not blow you will realise what a great first bike you have purchased, been there a number of times through my kids and always amazed me how it just kept going, safe riding to you all, great days ahead....
@stevekillick39053 ай бұрын
Great Video, Thanks. Could you confirm if the bearings you specified were for the Honda 435 UMK or 425 UMK?
@TinkerBod3 ай бұрын
Hi, sorry i dont have the cutter anymore to check, but at a guess i would say it was the 425. 👍
@BodgeGuy3 ай бұрын
Seem like a good idea. I have simlar 4x4 tower. My issue is heavy stone facing and cement. I probably need to modify a pallet. Only issue i can see if going up middle will interfere with diagonal poles. I'd like mine on the outstide. Should be fine if tower is secured to wall. Ill work something out.
@TinkerBod3 ай бұрын
Make a good set of these and dont let the youtube health and safety keyboard warriors see you kzread.info/dash/bejne/qHuKr5KbYpa6YdY.html
@martinmoss13463 ай бұрын
I've got a retractable towbar in my 2013 focus...one day the battery went flat and never worked since...every time I start the car I get 5 beeps and sometimes during driving.....any ideas what might be the problem
@racer81154 ай бұрын
So I did this and the rivet snapped off and is stuck. Anything I can do?
@MrBackflip5004 ай бұрын
My bike has fallen over while the steering was locked and the lock is broken inside. I can turn the key as usual but it stayes unlocked. I bought a replacement lock but I could not figure out how to remove bolt. Thank very much Sir!! Thank you.
@TinkerBod4 ай бұрын
Thanks for the positive comment 👍
@kopftuchgejo25415 ай бұрын
Super Danke 👍
@Kichu935 ай бұрын
Hi, here is how to resolve beeping with forscan: 1. Start programming of BCM (main), then select engineering mode from dropdown list. 2. Search for towbar and change to „with towbar attachment” 3. Search for trailer module and select the correct module (in my case 13 pin) 4. Turn off the ignition, get out and get in the car, start forscan again and create new car profile. It will find the TRM Module now. If not then give it some time with ignition off 5. Start TRM (as build) programming and modify the last line 791-03-01 to x19x. In my case I modified from 009C to 019C - it was automatically changed to 019D. After this I was able to use the button and towbar was retracting. Thank you very much for this video. It helped me a lot with fitting towbar to Ford Escape 2018 and definitely saved some money. Thankfully CAN cables were the same color (which is not always the case with US), additionally I had to drill a hole for the wiring loom in the trunk. It is catching the bumper a little when opening but I guess I would have to release the bolts and move the towbar back or front a little.
@bellofiore8946 ай бұрын
Very nice job. 👍👍
@TinkerBod6 ай бұрын
Thank you! Cheers!
@madeco836 ай бұрын
Hello @tinkerbod, I recently installed the same kit as you have, except that my car had a wiring harness ready in the trunk. I have a problem like yours, 24 minutes into the video, 2 beeps and no response. I have the cable and forscan, can you walk me through the process of activating the hook? I don't know where to find these options, the only thing I found and changed was the presence of a hook and the 13-pin harness.
@TinkerBod6 ай бұрын
Sorry, as in the video i took mine into a chap at the main dealers. He said he had trouble getting it to find the folding module but the lighting side was simple. How this was done i have no idea, sorry.
@Kichu935 ай бұрын
Hi, check my comment in case you still struggle with this issue.
@user-rd1pb8rk6j6 ай бұрын
Hello. Tell me, what kind of lubricant is used when assembling a gasoline crane on rubber bands?
@MrVM417 ай бұрын
Spot on for what I had to do to a old Honda, only thing is the rivit is bigger on the Honda and the one they gave was tiny.
@noriejohnyega12967 ай бұрын
I 'm looking one, the same. Briggs & Stratton V-Twin 18HP Vanguard, Petrol Engine. Quote me, please. Thanks.
@luqmanhaider93308 ай бұрын
You are using wrong thing at wrong place. This device is for resistive load not for inductive load
@UQRXD8 ай бұрын
Fiber glass dust.
@charnwilsenach63688 ай бұрын
Dragging it on too long.
@TinkerBod8 ай бұрын
Apologies, i will try harder next time just for you 👍
@sellma1118 ай бұрын
I have watched loads of these set ups and even though this is 4 years old it is one of the best i have seen,
@TinkerBod8 ай бұрын
Wow thank you 👍
@lifechanging325210 ай бұрын
To get that axle out from the riser you push the roll pin into the axle then hit the axle out. You’ll be able to hit the roll pin out after you remove the axle.
@nickblacker457310 ай бұрын
Do you know it the trailer module is the same for a fixed towbar?
@user-sk8eg7mo6u10 ай бұрын
Been looking a tail light number plate bracket 2 years now can't find one anywhere part number is 84701124600B . Where did you find onr
@colinguerrieria837410 ай бұрын
Hi pal would you be interested in fitting another one of these mate
@TinkerBod10 ай бұрын
No sorry only jobs for myself 👍
@colinguerrieria837410 ай бұрын
How did you know what Cambus wires to cut that bit look confusing
@colinguerrieria837410 ай бұрын
And the wire you put in fuse box. Mate mine already has it pal
@colinguerrieria837410 ай бұрын
Really appreciate it if i could contact your mate help me in doing mine mate much appreciated please
@TinkerBod10 ай бұрын
There are four wires canbus where the instructions tell you to cut either pair is ok.
@FJFxGaming10 ай бұрын
Hi, I've replaced my abs sensors but still no luck with the speedometer (RPM, fuel gage and temperature gauge all work), I bought the car from someone who said that it was working and all he did was remove the abs sensors to do some work on the front of the car and all I had to do was plug them back in so I ended up buying new ones as I didn't have the ones he took out and still no luck, my car is a 2008 ford mondeo 2.0 diesel with the converse+ clocks like yours
@TinkerBod10 ай бұрын
Have they damaged the wiring or plugs?
@eyeflynoosa11 ай бұрын
so you can withdraw the barrel if you have the key, is that correct? my bike has fallen over while the steering was locked and has jammed it in the locked position, I managed to unjam it but I don't trust the mechanism anymore and want to replace it.
@eyeflynoosa11 ай бұрын
nevermind, i managed to get it out without dremel or drilling, my 07 ktm 625 lock mechanism was a bit different though, it has a spring down inside the very bottom of the hole for the lock, the actual steel "bolt" that pushes into the steering column and had snapped away , I managed to get it out with needle nose players. thanks for uploading this video , I would have been fkd without it, cheers
@TinkerBod11 ай бұрын
Cheers, I'm glad it helped 👍
@ganeshparasuraman796511 ай бұрын
Now it's a brand new bike
@ganeshparasuraman796511 ай бұрын
Excellent
@TinkerBod11 ай бұрын
Thanks
@fernandodavidpoma789111 ай бұрын
thanks man!! totally useful video for my Kawasaki KLX300R 99
@TinkerBod11 ай бұрын
You're welcome!
@peterbrace690211 ай бұрын
Assume you don’t reinstall the original crash bar. Wish you had also included a bit about bolting the bar to the body. Any tips there?
@TinkerBod11 ай бұрын
Original slam panel goes on ebay. Bolting to the car is a simple task, if you have the bar then it can only go the one way. Use grease and waxoyl down the channels.
@terryrich428511 ай бұрын
Nice video mate, out of interest is it still in working order?
@TinkerBod11 ай бұрын
Indeed it is, its a great little lift. Not as good as the large one i made in my past videos to pick up the fireblade mind you 👌
@terryrich428511 ай бұрын
@@TinkerBod ah fest to hear bud! I have just bought one from 24mx I think the same just with a proworks sticker on it, I only have a exc350f so hopefully it's enough for that.. I'll have to watch that vid now boss
@TinkerBod11 ай бұрын
More than enough, just remember not to remove to much from one end of the bike without balancing it out, took the forks out of mine, luck i can move quick and catch well....
@terryrich428511 ай бұрын
@@TinkerBod omg 🤣
@jaycarva Жыл бұрын
Also can you share the info on the spokes for the rear wheel? I need one also.
@TinkerBod11 ай бұрын
The spoke was from ebay had to come from Germany for some reason.
@jaycarva Жыл бұрын
Great video mate! I'm fixing up a clapped out PW80 myself. Could you please share where you got the little rubber straps that hold the side cover plastics from flapping around?
@TinkerBod11 ай бұрын
All the parts were either ebay or fowlers of bristol 👍
@scotty2036 Жыл бұрын
I'd buy that
@gwendoline4116 Жыл бұрын
Thank you so much! Have you a webside to buy the pieces please ? Gwen from France ! 🙂
@TinkerBod Жыл бұрын
Hi Gwen I just used ebay for the branded bearings, just took number/code off bearing. For the genuine honda parts i just went to a local agricultural/garden machine seller, worked out cheaper than the internet. Not a diy home gardener shop but professional place. 👍good luck....
@Cee.Jay.71 Жыл бұрын
Besides the risk to consumers, what I find shocking is how little it would take for the manufacturer to do it right. We're literally talking pennies!
@vincentmcdonnell7986 Жыл бұрын
Ok
@andrericardo3550 Жыл бұрын
Eu já tenho a dax st 70 Depois honda chaly cf 70 Eeee gorilla z50j😮😮😮😮😮😮
Пікірлер
I have a 2016 Mondeo estate will it be the same method ??
If I got 190V in circuit? Does this thing could do 230V for my coffemachine?
Excellent video, well done 👍
Thank you! Cheers!
Hi I have the acc malfunction come up everytime. How do i reset that fault or what do i need to do. Ford mondeo 2009 titanium
You need to plug it in. If it does not reset on the ignition, then it's a plug-in job.
My Dad needs to replace his spark lead how do you get the fly wheel off to get to it?
On this one, you continue to unscrew the flywheel nut and it pulls off the flywheel, on others and later ones you need to remove nut and use an extractor
Hey thank you for taking the time to go through all this. What foot pegs did you use? And what 290mm shock did you find to use? I'm going to do the same.
Thanks, The foot pegs were off ebay and are for a rip off pw80, baja I think? and are identical to the genuine, be careful as some are chocolate. The shock was also just a random ebay looking at shock lenghs. I cant remember which bike but it definitely was not for a pw80. 👍
Thanks,
You're welcome!
This is very good, so the seal will seat the bushing?
It will all hold in together 👍
We made it!!! Thank you for this very helpful video. For some reason, the model we have had only 1 bush. The bush was so grasped we had to go to a machine shop to ask for help. The person in charge took the beam and tried on the press. It didn’t go! He had to use a torch to weaken the bush and then on the press it came off😁 We installed 2 bushes, a new pin and the MF is back on the track😁 Thanks again!!
Thanks 👍 the single bush is the normal standard unless loaders etc were specified anything applying extra load on the front axle.
What is the use of pulling it apart if you can’t find where to buy the gears from??
Who said i needed to change the gears?
Does not tell us where to buy the bevel gears. I’ve searched high and low and cannot find six tooth splined bevel gears anywhere!!!!
Im not your sales advisor.
Where did you buy the gears from??
I didn't, the bearings had gone as stated
My bike didn't have a key for the steering lock. I rode it to a local locksmiths who picked the lock and extracted it in about two minutes. Charged me £6. There was a number on the back of the lock so I was able to order a key and reuse it.
I have a similar engine (C25) to renovate. You said you found a workshop manual online. Do you remember where you found it? I have been looking without success. Thanks.
Hi, i paid a donation towards the museum below in the link, they had a very large online library of manuals. I have been to the website just now to check but they have reduced the makes. I would try contacting them and find out what happened to their library 👍 www.internalfire.com/
Would have been helpful to show how exactly you pulled it apart.
The bearings are a 'thermal fit'. Use heat to expand the aluminum case. Start with a modest amount, 100C-150C case temperature, but you may need to get to the point where the grease smokes slightly. A heat gun should be sufficient.
мужик, то что ты делаешь великолепно. все доходчиво, ничего лишнего. спасибо за работу.👍
Great comment, much appreciated. 👍
@@TinkerBod благодаря твоему видео, я завтра иду покупать pw80 своему сыну. Это будет его первый байк)
Great first bike and when the throttle is buried in the ground revving its guts out and it does not blow you will realise what a great first bike you have purchased, been there a number of times through my kids and always amazed me how it just kept going, safe riding to you all, great days ahead....
Great Video, Thanks. Could you confirm if the bearings you specified were for the Honda 435 UMK or 425 UMK?
Hi, sorry i dont have the cutter anymore to check, but at a guess i would say it was the 425. 👍
Seem like a good idea. I have simlar 4x4 tower. My issue is heavy stone facing and cement. I probably need to modify a pallet. Only issue i can see if going up middle will interfere with diagonal poles. I'd like mine on the outstide. Should be fine if tower is secured to wall. Ill work something out.
Make a good set of these and dont let the youtube health and safety keyboard warriors see you kzread.info/dash/bejne/qHuKr5KbYpa6YdY.html
I've got a retractable towbar in my 2013 focus...one day the battery went flat and never worked since...every time I start the car I get 5 beeps and sometimes during driving.....any ideas what might be the problem
So I did this and the rivet snapped off and is stuck. Anything I can do?
My bike has fallen over while the steering was locked and the lock is broken inside. I can turn the key as usual but it stayes unlocked. I bought a replacement lock but I could not figure out how to remove bolt. Thank very much Sir!! Thank you.
Thanks for the positive comment 👍
Super Danke 👍
Hi, here is how to resolve beeping with forscan: 1. Start programming of BCM (main), then select engineering mode from dropdown list. 2. Search for towbar and change to „with towbar attachment” 3. Search for trailer module and select the correct module (in my case 13 pin) 4. Turn off the ignition, get out and get in the car, start forscan again and create new car profile. It will find the TRM Module now. If not then give it some time with ignition off 5. Start TRM (as build) programming and modify the last line 791-03-01 to x19x. In my case I modified from 009C to 019C - it was automatically changed to 019D. After this I was able to use the button and towbar was retracting. Thank you very much for this video. It helped me a lot with fitting towbar to Ford Escape 2018 and definitely saved some money. Thankfully CAN cables were the same color (which is not always the case with US), additionally I had to drill a hole for the wiring loom in the trunk. It is catching the bumper a little when opening but I guess I would have to release the bolts and move the towbar back or front a little.
Very nice job. 👍👍
Thank you! Cheers!
Hello @tinkerbod, I recently installed the same kit as you have, except that my car had a wiring harness ready in the trunk. I have a problem like yours, 24 minutes into the video, 2 beeps and no response. I have the cable and forscan, can you walk me through the process of activating the hook? I don't know where to find these options, the only thing I found and changed was the presence of a hook and the 13-pin harness.
Sorry, as in the video i took mine into a chap at the main dealers. He said he had trouble getting it to find the folding module but the lighting side was simple. How this was done i have no idea, sorry.
Hi, check my comment in case you still struggle with this issue.
Hello. Tell me, what kind of lubricant is used when assembling a gasoline crane on rubber bands?
Spot on for what I had to do to a old Honda, only thing is the rivit is bigger on the Honda and the one they gave was tiny.
I 'm looking one, the same. Briggs & Stratton V-Twin 18HP Vanguard, Petrol Engine. Quote me, please. Thanks.
You are using wrong thing at wrong place. This device is for resistive load not for inductive load
Fiber glass dust.
Dragging it on too long.
Apologies, i will try harder next time just for you 👍
I have watched loads of these set ups and even though this is 4 years old it is one of the best i have seen,
Wow thank you 👍
To get that axle out from the riser you push the roll pin into the axle then hit the axle out. You’ll be able to hit the roll pin out after you remove the axle.
Do you know it the trailer module is the same for a fixed towbar?
Been looking a tail light number plate bracket 2 years now can't find one anywhere part number is 84701124600B . Where did you find onr
Hi pal would you be interested in fitting another one of these mate
No sorry only jobs for myself 👍
How did you know what Cambus wires to cut that bit look confusing
And the wire you put in fuse box. Mate mine already has it pal
Really appreciate it if i could contact your mate help me in doing mine mate much appreciated please
There are four wires canbus where the instructions tell you to cut either pair is ok.
Hi, I've replaced my abs sensors but still no luck with the speedometer (RPM, fuel gage and temperature gauge all work), I bought the car from someone who said that it was working and all he did was remove the abs sensors to do some work on the front of the car and all I had to do was plug them back in so I ended up buying new ones as I didn't have the ones he took out and still no luck, my car is a 2008 ford mondeo 2.0 diesel with the converse+ clocks like yours
Have they damaged the wiring or plugs?
so you can withdraw the barrel if you have the key, is that correct? my bike has fallen over while the steering was locked and has jammed it in the locked position, I managed to unjam it but I don't trust the mechanism anymore and want to replace it.
nevermind, i managed to get it out without dremel or drilling, my 07 ktm 625 lock mechanism was a bit different though, it has a spring down inside the very bottom of the hole for the lock, the actual steel "bolt" that pushes into the steering column and had snapped away , I managed to get it out with needle nose players. thanks for uploading this video , I would have been fkd without it, cheers
Cheers, I'm glad it helped 👍
Now it's a brand new bike
Excellent
Thanks
thanks man!! totally useful video for my Kawasaki KLX300R 99
You're welcome!
Assume you don’t reinstall the original crash bar. Wish you had also included a bit about bolting the bar to the body. Any tips there?
Original slam panel goes on ebay. Bolting to the car is a simple task, if you have the bar then it can only go the one way. Use grease and waxoyl down the channels.
Nice video mate, out of interest is it still in working order?
Indeed it is, its a great little lift. Not as good as the large one i made in my past videos to pick up the fireblade mind you 👌
@@TinkerBod ah fest to hear bud! I have just bought one from 24mx I think the same just with a proworks sticker on it, I only have a exc350f so hopefully it's enough for that.. I'll have to watch that vid now boss
More than enough, just remember not to remove to much from one end of the bike without balancing it out, took the forks out of mine, luck i can move quick and catch well....
@@TinkerBod omg 🤣
Also can you share the info on the spokes for the rear wheel? I need one also.
The spoke was from ebay had to come from Germany for some reason.
Great video mate! I'm fixing up a clapped out PW80 myself. Could you please share where you got the little rubber straps that hold the side cover plastics from flapping around?
All the parts were either ebay or fowlers of bristol 👍
I'd buy that
Thank you so much! Have you a webside to buy the pieces please ? Gwen from France ! 🙂
Hi Gwen I just used ebay for the branded bearings, just took number/code off bearing. For the genuine honda parts i just went to a local agricultural/garden machine seller, worked out cheaper than the internet. Not a diy home gardener shop but professional place. 👍good luck....
Besides the risk to consumers, what I find shocking is how little it would take for the manufacturer to do it right. We're literally talking pennies!
Ok
Eu já tenho a dax st 70 Depois honda chaly cf 70 Eeee gorilla z50j😮😮😮😮😮😮