My name is Willy and welcome to my KZread channel. It's just me working on my cars, trucks and of course my minibikes. So sit back and enjoy the videos. Thanks for watching!! Please subscribe if you haven’t already.
Did the same thing when replacing my seal, used bulk hose ad you solved the case of the mystery part number. Thank you sir, God bless.
@DIYWillyКүн бұрын
Thanks for watching!!
@philroberts42313 күн бұрын
THD is not the sound level. It is the total harmonic distortion of the unit! Thanks for the video!
@Scion15023 күн бұрын
OMG THANK YOU THIS WAS INFORMATIVE AND SO HELPFUL THANK YOU SIR ... 😊 JUST SUBSCRIBED TO YOU
@DIYWilly3 күн бұрын
Hello, So glad you liked the video! Have a blessed 4th and stay safe! Thanks for watching!!!
@manuelramirezmagic4 күн бұрын
Thank you 👍👍
@DIYWilly3 күн бұрын
Thanks for watching!!
@maxmason1724 күн бұрын
Can u plzz tell me WHY my mm80 won't go when weight is put on it. I've cleaned the carb several times still won't go.
@DIYWilly4 күн бұрын
Hello maxmason, It’s hard for me to diagnose your problems just from what you described. Just because you cleaned the carb doesn’t mean it’s right. Is the float adjusted correctly? Are the gaskets still good or could they be damaged. Could be fuel delivery. Are the valves adjusted correctly. How old is the engine? Might need a rebuild. That’s all I can offer without seeing and hearing it. Good luck man! Thanks for watching!!!
@Spacecruizer2034 күн бұрын
I actually liked the silver with the diy willy sticker
@Spacecruizer2034 күн бұрын
Since 2015 briggs stop letting the chinese's touch their engines they make them here since 2015 so i know what im talkin bout not just jibber jabber ya know 🤙
@DIYWilly4 күн бұрын
I know nothing about them… couple bolts and a whole lot of paint and done! Rebuilt!!😂
@Spacecruizer2034 күн бұрын
Since 2015 briggs stop letting the chinese's touch their engines they make them here since 2015 so i know what im talkin bout not just jibber jabber ya know 🤙
@Spacecruizer2034 күн бұрын
When i take my cylinder head off its been 3 years should i get a new piston or just clean her up and can i sand lightly to get the black off cuz i put my olight in the spark plug hole and i can see its not silver no more she black 🕳lol
@DIYWilly4 күн бұрын
Definitely don’t sand it if your not removing the piston. You can take small wire brush or tooth brush and clean the top with carb cleaner. You will also need to change the oil afterwards because of the carb cleaner getting inside the block. Are you going to change head gasket also? Good time for all new gaskets.
@Spacecruizer2034 күн бұрын
Its lighter then a predator too and built in USA 💪🏼💯🔥🔥🔥🔥
@DIYWilly4 күн бұрын
I think it turned great. I put the little Briggs back on the MM80 frame today. New minibike video coming soon.
@KB_Joys6 күн бұрын
Whats the spring gasket washer for? And is it necessary?
@DIYWilly3 күн бұрын
Hello, If you’re referring to the white washer below the spring I would say it’s there to keep the spring from coming contact with the slide. Is it necessary probably not but is a nice added to a great carb. Maybe someone else will provide a better answer. Thanks for watching!!
@KB_Joys3 күн бұрын
@@DIYWilly nibbi have gotten back to me about this, they said what you said about protecting the inside of the throttle body from the spring, but they also said it was to help keep the cable from slipping. Apparently there were issues with the cable not making great contact. I was thinking maybe there should be an adjustment at the top of the carburetor, like all the others, lol Its a good carburetor for sure, but since i lost the plastic white washer, im using a black rubber washer that i found and it fits perfectly in there. Thanks for reaching out, i appreciate it 😊
@DIYWilly3 күн бұрын
Thanks for the clarification and sure it help someone with the same question. Happy 4th and stay safe!!
@ohio_thunder836 күн бұрын
I have the same code on my 2010 Nissan versa. I also have a hole in my exhaust near the upstream(air/fuel ratio) 02 sensor and have been getting a code for the o2 sensor as well. Could the O2 sensor issue be causing the misfire?
@DIYWilly6 күн бұрын
No wouldn’t think so. You should get the hole in the exhaust plug welded. That may correct the O2 sensor code. Try the simple troubleshooting for the misfire. Move the plug and coil to different cylinders and watch the code. My guess is you have a tired coil. Thanks for watching!!
@ozzman5308 күн бұрын
Thanks Willy. I went and grabbed this same scanner after watching this video. I couldn't find another cheap option to reset my alcohol content and the 3 or 4 scanners I have dont have this option. I think it's pretty cool you can update these but it's getting harder and harder to keep up with the best options to maintain a modern vehicle. Thanks again and I really appreciate you walking through where you found the setting.
@DIYWilly8 күн бұрын
Hello ozzman, Glad you liked the video. Good luck with the reset on your truck. Thanks for watching!!
@Yosser708 күн бұрын
Would it be safe or even possible to charge the ryobi battery, if you had 2 coils? Think it would need a rectifier to convert the current.
@DIYWilly8 күн бұрын
Hello Dave, It would be possible to charge with coils and rectifier but I don’t think it would be safe. Lithium batteries are very particular on how they’re charged. The charge from the coils is small and would take a long time. If you want to use charging coils than I would suggest a different battery. Thanks for watching!!
@Yosser708 күн бұрын
@@DIYWilly Yeah I kinda thought that but thanks for the clarification 👍🏻 Probably best sticking to a small motorbike battery.
@dougkubash86739 күн бұрын
Good job! Sounds good!
@DIYWilly9 күн бұрын
Hello Doug, Thanks for watching!!
@jeffadinolfi80239 күн бұрын
Thanks bro, but I can’t see it because it’s in the shade
@DIYWilly9 күн бұрын
Thanks for watching!!
@slikk-trent11 күн бұрын
What wheels are those?
@DIYWilly10 күн бұрын
Hello, These are the 10” modular wheels from GoPowerSports. Thanks for watching!!
@slikk-trent10 күн бұрын
@@DIYWilly thanks brotha
@wildlife521212 күн бұрын
You can hear the carburetor choking. Not getting enough gas!
@DIYWilly12 күн бұрын
I have thought about using a fuel pump on a couple of my engines. Thanks for watching!!
@KentuckyFriedFixes13 күн бұрын
Excellent work Willy! Love that new red and black color scheme. It looks fast just sitting on the bench!
@DIYWilly13 күн бұрын
I hope it runs as good as it looks. Really concerned about the kool bore and the honing. I’ll be putting it on the frame soon and seeing if things worked as they should. Getting hot over here in Cali and the heat makes it hard to work on the projects. Thanks for watching!!
@Spacecruizer2034 күн бұрын
@DIYWilly I always watch news from other states they say Texas and Cali has never seen heat like this coming up since the 1800s 🙏
@DIYWilly4 күн бұрын
@@Spacecruizer203Yep it’s definitely a hot one today. I did manage to get some work done on Biggs and the MM80 frame today.
@Spacecruizer2034 күн бұрын
@@DIYWilly watermelon is the key and some cold beer
@Spacecruizer2034 күн бұрын
@@DIYWilly can't wait to see u take her out for a cruize
@Lou-eye13 күн бұрын
Good job Willy! Looks good too!👍
@DIYWilly13 күн бұрын
Hope it runs as good as it looks. Haven’t tried to start it yet. Gotta get the bike out now and get some repairs done from the accident it had in Dec. Thanks for watching!!
@phoenixmojado52714 күн бұрын
Can I use mikuni jets with the nibbi carb
@DIYWilly14 күн бұрын
No I don’t believe they’re the same. These are the jets I used.. amzn.to/4bcsI8l Thanks for watching!!
@phoenixmojado52714 күн бұрын
Ty sir 🫡 the 115 it came with got me growing pretty smooth so far
@DIYWilly14 күн бұрын
Good luck, have fun and be safe!!
@224megamoto14 күн бұрын
did you need a mount to fit the motor on?
@DIYWilly14 күн бұрын
No I drilled new holes to match the engine in the mounting plate. I made template of the bottom of the engine and measured it out to align the chain. Marked the holes and drilled. Worked perfectly as long as you have a chain tensioner. Thanks for watching!!
@slurrbeats15 күн бұрын
How has it held up 3 years later ? I’d love to know im about to get mine in and installed on my 08 nismo frontier
@DIYWilly14 күн бұрын
Hello Slurrbeats, The Pedal Commander still going strong. The issues at all. Thanks for watching!!
@frankjago902018 күн бұрын
Thanks Willy! Gonna do this today. Thanks for the help!
@frankjago902018 күн бұрын
6/19/2024. Thanks again!!
@DIYWilly18 күн бұрын
Hello Frank, I hope the repair goes well for you. Thanks for watching!!
@DIYWilly16 күн бұрын
👍
@TGF00Buck19 күн бұрын
Quick follow up, did changing it at 170 cause any issues for you often time if you change atf that has never been changed you can introduce slipping and gear loss. Did you expereince any of that?
@DIYWilly19 күн бұрын
Hello, Great question!! We haven’t experienced any issues with the transmission. The truck drives amazingly well considering the mileage and abuse it gets. Thanks for watching!!
@TGF00Buck19 күн бұрын
@@DIYWilly thank you so much for the reply. My father requested I change the fluid on his 90k trans and it had not be changed before, so was doing some research.
@vicvasquez855419 күн бұрын
was it a fuel injector
@DIYWilly19 күн бұрын
Hello Vic, No it was the spark plugs. I’ve already changed the fuel injectors when I had the 219A code. Thanks for watching!!
@vicvasquez855419 күн бұрын
oh ok thank you yea i have that same code right now on a 2015 sierra denali 6.2 trying to figure it out
@DIYWilly19 күн бұрын
This is where it can get scary. We all know about the AFM/DOD problems with these engines. I hope this is not the problem you’re having. Thanks for watching!!
@bernyflores455719 күн бұрын
Hola a cuántas libras va el torque por favor gracias
@DIYWilly19 күн бұрын
The transmission pan bolts torque to 70 in-lbs. Thanks for watching!!
@andrewprosser999520 күн бұрын
Do you have a video on how to install the monitor?
@DIYWilly20 күн бұрын
Hello Andrew, No unfortunately I do not have a video for install the head unit. Both trucks already had them when installing the cameras. Thanks for watching.
@KentuckyFriedFixes20 күн бұрын
Big work ahead! If you can get that Ecotec shoehorned into the chassis, that thing is gonna be a rocket!
@DIYWilly20 күн бұрын
I ordered several different size shoe horns from Amazon. Should be able to get the Ecotec in there with some sawzall action! Just need to align the clutch and I’m golden. Thanks for checking it out!!
@Spacecruizer20321 күн бұрын
So its a one of a kind custom ecotec razor thats sick people need to start tuning I n 💪🏼💯💨💨💨
@DIYWilly21 күн бұрын
Dude it’s going to be crazy. Others have used the Ecotec in buggies and it’s pretty a good engine choice. Just need to make it all work in the stretched RZR 900 chassis.
@heathenprojects263921 күн бұрын
Pretty cool Willy im shopping for a wreaked smart car to drop the hybrid system into my old vw
@DIYWilly21 күн бұрын
That would be a great project! Thanks checking it out!!
@Spacecruizer2034 күн бұрын
That sounds sick
@Lou-eye21 күн бұрын
Now the technical geometry design fun begins, its an adventure Willy i know you enjoy👍. Im thinking(my 2cents) when you move that engine back closer to the Differential you might want to put a heatshield between there to keep some eng. heat off the diff.🤔. 👌
@DIYWilly21 күн бұрын
I kinda feels like a square peg in a round hole. It will fit but not till after some more fun with the sawzall. I will be installing a lot of heat shielding and a good firewall. Good to be working on the BAJA RZR Project again! Thanks for checking it out!!
@anthonyimperato816321 күн бұрын
Exactly what happened to mine...thank you
@DIYWilly21 күн бұрын
Hello Anthony, The replacement parts aren’t expensive but this is a good alternative fix for the broken part. Thanks for watching!!!
@dahatchery22 күн бұрын
Greatest explanation, you didn’t cover how to lower the glass if it’s stuck in the up position. So how do you do that now that all is disconnected?
@DIYWilly22 күн бұрын
Hello Bill, If I needed to do this job with the window up, I would still unbolt the glass first by either reaching inside or making new holes in the door to use a socket on the bolts. Thanks for watching!!
@elmeraperez22 күн бұрын
GREAT. THX FOR THE VIDEO
@DIYWilly22 күн бұрын
Thanks for watching!!
@certifiedgeek0523 күн бұрын
Hey Willy, I just got this kit for my Predator 224cc. Everything was good. They should have included 4 of those spaces. I got 4 nice spaces from Ace for the modified case cover. Pretty happy with everything so far. Thanks for the great video that helped me so much since my generic kit didn't include any instructions.
@DIYWilly23 күн бұрын
Hello David, So glad to hear you electric start conversion went well. What did you use as a battery? Have fun and stay safe! Thanks for watching!!
@certifiedgeek0520 күн бұрын
@@DIYWilly I meant spacers, geez. Where is grammar check when you need it? I ended up getting the MightyMax Model YB9A-A 12volt 9amp battery. It works perfect.
@DIYWilly20 күн бұрын
Hello David, So when you say case cover.. Are you referring to the blower housing and pull start? Good choice for a battery. I will probably change from the RYOBI to a regular battery. I plan on building this engine again and I don’t think the current battery will have enough juice. Do you have any pix posted anywhere to see your build? Have you done anything to the 224?
@krperry200723 күн бұрын
What is the purpose of the spacer?
@DIYWilly23 күн бұрын
The spacer is designed to improve horsepower and torque across the powerband where your truck needs it the most. Thanks for watching!!
@jimmyseitz500123 күн бұрын
Thank You but you didn't show how easy it was to reinstall the 8 mm nuts?? God Bless 🙏
@DIYWilly23 күн бұрын
Hello Jimmy, I believe I went through the complete process including reinstall of the nuts and covers on the inside. What I didn’t show was I actually dropped one inside the headliner and had to go find it..😂 Thanks for watching!!
@krperry200723 күн бұрын
I dropped my 3/8 extension at the same step! I haven’t been able to find it.
@DIYWilly23 күн бұрын
Hello Krperry, Hopefully the 3/8 extension will fall out on its own. Did you look down at the skid plate? The spacer is designed to improve horsepower and torque across the powerband where your truck needs it the most. Thanks for watching!!
@Junior-qe8gq24 күн бұрын
I have same code and chevy dealer says #3 too rich and they need to replace all... this video helped me to have an idea on how to DIY
@DIYWilly24 күн бұрын
Hello Junior, So glad the video helped you.. Thanks for watching!!
@donaldfennell97124 күн бұрын
Hi Willie, are there 1/4 inch saw blades for these porta bandsaws? I would be able to to make curved cuts.
@DIYWilly24 күн бұрын
Hello Donald, Harbor Fright does sell 1/4” blades however the a too long for this band saw. Thanks for watching!!
Пікірлер
Did the same thing when replacing my seal, used bulk hose ad you solved the case of the mystery part number. Thank you sir, God bless.
Thanks for watching!!
THD is not the sound level. It is the total harmonic distortion of the unit! Thanks for the video!
OMG THANK YOU THIS WAS INFORMATIVE AND SO HELPFUL THANK YOU SIR ... 😊 JUST SUBSCRIBED TO YOU
Hello, So glad you liked the video! Have a blessed 4th and stay safe! Thanks for watching!!!
Thank you 👍👍
Thanks for watching!!
Can u plzz tell me WHY my mm80 won't go when weight is put on it. I've cleaned the carb several times still won't go.
Hello maxmason, It’s hard for me to diagnose your problems just from what you described. Just because you cleaned the carb doesn’t mean it’s right. Is the float adjusted correctly? Are the gaskets still good or could they be damaged. Could be fuel delivery. Are the valves adjusted correctly. How old is the engine? Might need a rebuild. That’s all I can offer without seeing and hearing it. Good luck man! Thanks for watching!!!
I actually liked the silver with the diy willy sticker
Since 2015 briggs stop letting the chinese's touch their engines they make them here since 2015 so i know what im talkin bout not just jibber jabber ya know 🤙
I know nothing about them… couple bolts and a whole lot of paint and done! Rebuilt!!😂
Since 2015 briggs stop letting the chinese's touch their engines they make them here since 2015 so i know what im talkin bout not just jibber jabber ya know 🤙
When i take my cylinder head off its been 3 years should i get a new piston or just clean her up and can i sand lightly to get the black off cuz i put my olight in the spark plug hole and i can see its not silver no more she black 🕳lol
Definitely don’t sand it if your not removing the piston. You can take small wire brush or tooth brush and clean the top with carb cleaner. You will also need to change the oil afterwards because of the carb cleaner getting inside the block. Are you going to change head gasket also? Good time for all new gaskets.
Its lighter then a predator too and built in USA 💪🏼💯🔥🔥🔥🔥
I think it turned great. I put the little Briggs back on the MM80 frame today. New minibike video coming soon.
Whats the spring gasket washer for? And is it necessary?
Hello, If you’re referring to the white washer below the spring I would say it’s there to keep the spring from coming contact with the slide. Is it necessary probably not but is a nice added to a great carb. Maybe someone else will provide a better answer. Thanks for watching!!
@@DIYWilly nibbi have gotten back to me about this, they said what you said about protecting the inside of the throttle body from the spring, but they also said it was to help keep the cable from slipping. Apparently there were issues with the cable not making great contact. I was thinking maybe there should be an adjustment at the top of the carburetor, like all the others, lol Its a good carburetor for sure, but since i lost the plastic white washer, im using a black rubber washer that i found and it fits perfectly in there. Thanks for reaching out, i appreciate it 😊
Thanks for the clarification and sure it help someone with the same question. Happy 4th and stay safe!!
I have the same code on my 2010 Nissan versa. I also have a hole in my exhaust near the upstream(air/fuel ratio) 02 sensor and have been getting a code for the o2 sensor as well. Could the O2 sensor issue be causing the misfire?
No wouldn’t think so. You should get the hole in the exhaust plug welded. That may correct the O2 sensor code. Try the simple troubleshooting for the misfire. Move the plug and coil to different cylinders and watch the code. My guess is you have a tired coil. Thanks for watching!!
Thanks Willy. I went and grabbed this same scanner after watching this video. I couldn't find another cheap option to reset my alcohol content and the 3 or 4 scanners I have dont have this option. I think it's pretty cool you can update these but it's getting harder and harder to keep up with the best options to maintain a modern vehicle. Thanks again and I really appreciate you walking through where you found the setting.
Hello ozzman, Glad you liked the video. Good luck with the reset on your truck. Thanks for watching!!
Would it be safe or even possible to charge the ryobi battery, if you had 2 coils? Think it would need a rectifier to convert the current.
Hello Dave, It would be possible to charge with coils and rectifier but I don’t think it would be safe. Lithium batteries are very particular on how they’re charged. The charge from the coils is small and would take a long time. If you want to use charging coils than I would suggest a different battery. Thanks for watching!!
@@DIYWilly Yeah I kinda thought that but thanks for the clarification 👍🏻 Probably best sticking to a small motorbike battery.
Good job! Sounds good!
Hello Doug, Thanks for watching!!
Thanks bro, but I can’t see it because it’s in the shade
Thanks for watching!!
What wheels are those?
Hello, These are the 10” modular wheels from GoPowerSports. Thanks for watching!!
@@DIYWilly thanks brotha
You can hear the carburetor choking. Not getting enough gas!
I have thought about using a fuel pump on a couple of my engines. Thanks for watching!!
Excellent work Willy! Love that new red and black color scheme. It looks fast just sitting on the bench!
I hope it runs as good as it looks. Really concerned about the kool bore and the honing. I’ll be putting it on the frame soon and seeing if things worked as they should. Getting hot over here in Cali and the heat makes it hard to work on the projects. Thanks for watching!!
@DIYWilly I always watch news from other states they say Texas and Cali has never seen heat like this coming up since the 1800s 🙏
@@Spacecruizer203Yep it’s definitely a hot one today. I did manage to get some work done on Biggs and the MM80 frame today.
@@DIYWilly watermelon is the key and some cold beer
@@DIYWilly can't wait to see u take her out for a cruize
Good job Willy! Looks good too!👍
Hope it runs as good as it looks. Haven’t tried to start it yet. Gotta get the bike out now and get some repairs done from the accident it had in Dec. Thanks for watching!!
Can I use mikuni jets with the nibbi carb
No I don’t believe they’re the same. These are the jets I used.. amzn.to/4bcsI8l Thanks for watching!!
Ty sir 🫡 the 115 it came with got me growing pretty smooth so far
Good luck, have fun and be safe!!
did you need a mount to fit the motor on?
No I drilled new holes to match the engine in the mounting plate. I made template of the bottom of the engine and measured it out to align the chain. Marked the holes and drilled. Worked perfectly as long as you have a chain tensioner. Thanks for watching!!
How has it held up 3 years later ? I’d love to know im about to get mine in and installed on my 08 nismo frontier
Hello Slurrbeats, The Pedal Commander still going strong. The issues at all. Thanks for watching!!
Thanks Willy! Gonna do this today. Thanks for the help!
6/19/2024. Thanks again!!
Hello Frank, I hope the repair goes well for you. Thanks for watching!!
👍
Quick follow up, did changing it at 170 cause any issues for you often time if you change atf that has never been changed you can introduce slipping and gear loss. Did you expereince any of that?
Hello, Great question!! We haven’t experienced any issues with the transmission. The truck drives amazingly well considering the mileage and abuse it gets. Thanks for watching!!
@@DIYWilly thank you so much for the reply. My father requested I change the fluid on his 90k trans and it had not be changed before, so was doing some research.
was it a fuel injector
Hello Vic, No it was the spark plugs. I’ve already changed the fuel injectors when I had the 219A code. Thanks for watching!!
oh ok thank you yea i have that same code right now on a 2015 sierra denali 6.2 trying to figure it out
This is where it can get scary. We all know about the AFM/DOD problems with these engines. I hope this is not the problem you’re having. Thanks for watching!!
Hola a cuántas libras va el torque por favor gracias
The transmission pan bolts torque to 70 in-lbs. Thanks for watching!!
Do you have a video on how to install the monitor?
Hello Andrew, No unfortunately I do not have a video for install the head unit. Both trucks already had them when installing the cameras. Thanks for watching.
Big work ahead! If you can get that Ecotec shoehorned into the chassis, that thing is gonna be a rocket!
I ordered several different size shoe horns from Amazon. Should be able to get the Ecotec in there with some sawzall action! Just need to align the clutch and I’m golden. Thanks for checking it out!!
So its a one of a kind custom ecotec razor thats sick people need to start tuning I n 💪🏼💯💨💨💨
Dude it’s going to be crazy. Others have used the Ecotec in buggies and it’s pretty a good engine choice. Just need to make it all work in the stretched RZR 900 chassis.
Pretty cool Willy im shopping for a wreaked smart car to drop the hybrid system into my old vw
That would be a great project! Thanks checking it out!!
That sounds sick
Now the technical geometry design fun begins, its an adventure Willy i know you enjoy👍. Im thinking(my 2cents) when you move that engine back closer to the Differential you might want to put a heatshield between there to keep some eng. heat off the diff.🤔. 👌
I kinda feels like a square peg in a round hole. It will fit but not till after some more fun with the sawzall. I will be installing a lot of heat shielding and a good firewall. Good to be working on the BAJA RZR Project again! Thanks for checking it out!!
Exactly what happened to mine...thank you
Hello Anthony, The replacement parts aren’t expensive but this is a good alternative fix for the broken part. Thanks for watching!!!
Greatest explanation, you didn’t cover how to lower the glass if it’s stuck in the up position. So how do you do that now that all is disconnected?
Hello Bill, If I needed to do this job with the window up, I would still unbolt the glass first by either reaching inside or making new holes in the door to use a socket on the bolts. Thanks for watching!!
GREAT. THX FOR THE VIDEO
Thanks for watching!!
Hey Willy, I just got this kit for my Predator 224cc. Everything was good. They should have included 4 of those spaces. I got 4 nice spaces from Ace for the modified case cover. Pretty happy with everything so far. Thanks for the great video that helped me so much since my generic kit didn't include any instructions.
Hello David, So glad to hear you electric start conversion went well. What did you use as a battery? Have fun and stay safe! Thanks for watching!!
@@DIYWilly I meant spacers, geez. Where is grammar check when you need it? I ended up getting the MightyMax Model YB9A-A 12volt 9amp battery. It works perfect.
Hello David, So when you say case cover.. Are you referring to the blower housing and pull start? Good choice for a battery. I will probably change from the RYOBI to a regular battery. I plan on building this engine again and I don’t think the current battery will have enough juice. Do you have any pix posted anywhere to see your build? Have you done anything to the 224?
What is the purpose of the spacer?
The spacer is designed to improve horsepower and torque across the powerband where your truck needs it the most. Thanks for watching!!
Thank You but you didn't show how easy it was to reinstall the 8 mm nuts?? God Bless 🙏
Hello Jimmy, I believe I went through the complete process including reinstall of the nuts and covers on the inside. What I didn’t show was I actually dropped one inside the headliner and had to go find it..😂 Thanks for watching!!
I dropped my 3/8 extension at the same step! I haven’t been able to find it.
Hello Krperry, Hopefully the 3/8 extension will fall out on its own. Did you look down at the skid plate? The spacer is designed to improve horsepower and torque across the powerband where your truck needs it the most. Thanks for watching!!
I have same code and chevy dealer says #3 too rich and they need to replace all... this video helped me to have an idea on how to DIY
Hello Junior, So glad the video helped you.. Thanks for watching!!
Hi Willie, are there 1/4 inch saw blades for these porta bandsaws? I would be able to to make curved cuts.
Hello Donald, Harbor Fright does sell 1/4” blades however the a too long for this band saw. Thanks for watching!!