Quick Easy Cylinder Hone and Valve Job on My Briggs Snow Blower Engine - Biggs Refresh EP 3
Автокөліктер мен көлік құралдары
On today’s Episode of DIY Willy. I attempt to do a quick hone to remove the glaze and valve job to refresh Biggs my Briggs and Stratton snow blower engine
So follow along as we rebuild Biggs the snow blower monster..
**If you found this video helpful or entertaining, PLEASE consider donating by using the $Thanks-Tab$ located below the video, allowing me to continue making these types of videos. **
Your thanks is greatly appreciated!
Briggs and Stratton Build Playlist:
• Briggs and Stratton Bu...
Tools Used (Affiliate Links)
Kuntec Engine Cylinder Hone Tool….amzn.to/3WXTrSB
400 Grit Replacement stones….amzn.to/3WXxzqx
Flex Hone Oil 32oz….amzn.to/4bU5ftg
Other great small engine builders:
@KentuckyFriedFixes
Cameras / Gear Used In Filming (Affiliate Links)
GoPro HERO 9 Black….amzn.to/41Onhte
GoPro Hero 7 Silver….amzn.to/3RNmrsk
60” Tripod….amzn.to/3NPifHm
GoPro Shorty Hand held/Tripod….amzn.to/3tIsfLC
Thanks for watching and enjoy the video....
Hit that Subscribe Button....
Please consider subscribing if you haven’t already, Give it a thumb up, leave a comment and please share these videos.
You can reach me at: diywilliyprojects@gmail.com
Music (Royalty Free):
Song: Bass-Groovy-Beat
Website: sfx.productioncrate.com/
Filmed with a GoPro Hero 9 Black
Edited with DaVinci Resolve Studio 18.6
Disclaimer:
Please do not try to re-enact or recreate anything you see in my videos.
DIY Willy does not take any responsibility for injuries or equipment failure created by doing so.
These videos are intended for entertainment only.
#briggsandstratton #superclean #briggs #Predator #honda #snowblower #engine #minibike #megamoto #mm80 #diywilly
Пікірлер: 10
Good stuff! I can't wait for Biggs to be brought back to life. You may need an .010 oversize top ring for Biggs though.
@DIYWilly
Ай бұрын
Yes I measured it tonight and it’s bigger. My parts search continues. I might just send it..😂
Now that's some clean work willy lookin COleeeeN🧨
@DIYWilly
Ай бұрын
Thanks man I really love building these engines..
Glad you checked those cam lobes Willy👍. The only engines I've delt with had a steel sleeve or electroplating on alum. cylinder walls, didnt think solid alum.cylinders would hold up to the heat and wear? Briggs looking good👍
@DIYWilly
Ай бұрын
The new cam should be an improvement over the old. Thanks for the suggestion. The aluminum cylinders work I guess if you have the right rings. I’ve been trying to get new rings but having trouble with parts. I’ve bought two different ones and they both didn’t fit. These Briggs parts numbers…🤯🤯 I’ll put it back together with what I have and cross my fingers it works better. Thanks for watching!!
@WalkerSmallEnginePerformance
Ай бұрын
I think Briggs & Stratton called it Cool Bore? I know they made a boatload of them and they worked. I've seen aluminum bores on some exotic high performance car engines too.
@DIYWilly
Ай бұрын
Shouldn’t have got started with these old engines.. Parts are hard to find!
@WalkerSmallEnginePerformance
Ай бұрын
@@DIYWilly I went to Briggs training school 20 years ago and became a Master Service Tech. Then never worked on any. Go figure. I remember them telling us that they were going to slowly stop supporting the flathead stuff even then.
@DIYWilly
Ай бұрын
Desperately trying to find correct rings. It’s ashamed they stop the support on the flat head.