Пікірлер

• 
  @saikakam13 күн бұрын

  that's pure over engineering . thanks anyway

• 
  @Selmer1430P14 күн бұрын

  That would have been nice to have a month ago as I was burning up boards on a disc sander. Do you have any brick and mortar( I'm in Denver area) or just online?

• 
  @maximumguitarworks14 күн бұрын

  We have a factory outside Denver…but not a retail store. Some people stop by to pick up orders…it to drop off guitars for Plek service. But this needs to be done by appointment. Call the number on our website if you need help. Thanks for watching.

• 
  @baimun15 күн бұрын

  When I put steel grommets into guitar necks, I just put the insert bit into my drill press and (obviously with the power off) use the perfectly vertical pressure from the press and I turn the chuck with my bare hand. The other fantastic feature of the steel grommets are if you use four recessed neck ferrules instead of a plate, it's much easier to find metric bolts of various lengths, or even cut a longer bolt down. It's much more difficult to find the short wood screws necessary for a tapered neck heel to keep the bolts from poking all the way through.

• 
  @apexclaimadjusters581617 күн бұрын

  Great vid process ect... did part 2 ever materialize

• 
  @inourvendetta117 күн бұрын

  Do the telecaster templates and the telemaster templates fit fender necks if i just want to build the body?

• 
  @inourvendetta117 күн бұрын

  Do your telecaster and telemaster templates fit fender necks if i just want to build the body? Great videos

• 
  @carlrockaway169618 күн бұрын

  Do you sell those guitar templates?

• 
  @maximumguitarworks18 күн бұрын

  Yes. Although it wasn’t my intention…it became a business. maximumguitarworks.com Call the number on the website if you need help.

• 
  @leonarddaneman81023 күн бұрын

  The adjustable pocket template can be accomplished with three pieces of mdf taped to the blank around the heel of your neck lined up to the center line to the line drawn for the scale length. The route (tweaked with tape) will match that particular neck. I use a cheap laser to line the neck up with the blank's center line.

• 
  @jamescopeland535824 күн бұрын

  Cool

• 
  @jamescopeland535825 күн бұрын

  Good video

• 
  @acusticsix27 күн бұрын

  great job! i need to do this to my strat with striped wood screws.... anyway you could ditch the nut driver and chuck your home made driver into the drill press, spin the chuck by hand while putting small amount of pressure on handle for leverage.... a little wax and they go in dead straight every time...

• 
  @AldowainАй бұрын

  I very, very much appreciate these videos for their expertise, however, anybody contemplating their very first guitar build would likely never set foot on that path having watched this series. Sometimes, you just have to have at it, and be damned with all the jigs. You just have to give it a go and learn from your mistakes.

• 
  @derekbascombe7731Ай бұрын

  At 22:00 Steve could use the special tool he says he doesn't like by setting it into the chuck of his drill press - the perfect perpendicularity of the alignment is still assured from drilling the original holes! - and then start turning the chuck by hand while gently pressing down on the plunge handle of the press. Most drill presses are designed to allow such hand-turning of the chuck...

• 
  @Cymbaline713Ай бұрын

  Question regarding planing the neck blank down to the desired thickness - I don't have a planer, but I do have a jointer. Would that also work to get it down to the thickness I want?

• 
  @maximumguitarworksАй бұрын

  Not ideal…but possible. You will have to pay attention to all four corners of the blank…and take light passes on the jointer. I have found that you can put more pressure with the push blocks over the thicker ends/sides…and slowly make adjustments to make the sides flat and parallel. It’s not easy…but possible.

• 
  @shanemichaels8289Ай бұрын

  I just did a belly cut and forearm bevel with an orbital sander Works really well

• 
  @Dreymann68Ай бұрын

  Great video 👍👍 do you sell this templates ?? Thanks Lars

• 
  @maximumguitarworksАй бұрын

  Yes. Go to the website…many different template sets available there. maximumguitarworks.com

• 
  @joeanzalone54362 ай бұрын

  Your video are so great! Thanks for sharing your expert knowledge!!

• 
  @tubephase2 ай бұрын

  Goodnight! I was wondering what this mold is for? I watched the whole video thinking I would have an answer, but I stayed the same. If it's not due to my lack of education, I can ask you and see how the mold is used more trade after it's ready. Thank you very much in advance for your attention and congratulations on the very good KZread channel.

• 
  @PierreAntoineRoiron6 күн бұрын

  Answer is at 42:03

• 
  @CMRWoodworks2 ай бұрын

  This is great! Looking forward to binge watching the rest of this series! Lots of great info already!

• 
  @CMRWoodworks2 ай бұрын

  Man, I‘m so glad I came across this video. I didn‘t know you had a KZread channel until today. I‘ve heard a lot about you through Todd‘s videos over at Sweet T Guitars. I have seen him do this and am planning on doing the same in my first electric build. Thanks for the detail! I appreciate it. I am now subscribed as well!

• 
  @barryminbiole61992 ай бұрын

  You don't really need perpendicular holes. You need co-linear holes. So drill a smaller pilot hole thru both the body and neck. Then drill at the needed diameters

• 
  @seanflynn8002 ай бұрын

  Great to see decent engineering principles being applied to an age old problem. I think Leo himself would've approved. Would be interesting to see if unplugged resonance could even result for the couch surfers amongst us.

• 
  @milesa-c38652 ай бұрын

  No mask?

• 
  @ryanmccabe78212 ай бұрын

  Great video, what thickness of aluminium are you using?

• 
  @ScheltemaBoutiqueGuitars2 ай бұрын

  Hey man. So nice to see your setup. Looks awesome. Thanks for the shout out

• 
  @feggymango2 ай бұрын

  What would be the best way to round over the edge after you make the cut? Would it done by hand?

• 
  @KleshGuitarsOfficial2 ай бұрын

  I like the clean-ness and uniformity of your templates. Mine all look terrible, (either baltic birch or MDF) but still work, but would be nice to have some of these. Great job

• 
  @KleshGuitarsOfficial2 ай бұрын

  Cool video! I just subscribed, gonna check out some of your other videos rn

• 
  @johnmicalizzi1262 ай бұрын

  I always said that using inserts the modern way !

• 
  @An2oine2 ай бұрын

  Lucky my neck I bought was a SCREW on neck. ;+)

• 
  @mauikrawalski10742 ай бұрын

  An equal length and geometry of the cross section is important when comparing the stifness. The titanium has a different dimensions, according to it´s cross section, than the maple and carbon rods.

• 
  @BurninSven12 ай бұрын

  Thanks for the good tips you provide. I made a cheap tool for positioning the tailpiece kzread.info/dash/bejne/Znuqyc2roL2fiLw.htmlsi=Kfd-SJYdX8KD308w

• 
  @chukka622 ай бұрын

  very interesting but the scale you are using came from aliexpress and is false i have 2 of them and they dtgive the same reading.

• 
  @bohs19842 ай бұрын

  Just grab it with both hands and head over to your belt sender. 30 seconds, DONE.

• 
  @tomsisson6603 ай бұрын

  Do you build and sell these guitar jigs? Tom Sisson

• 
  @eliyam273 ай бұрын

  Thanks! This is very helpful and fun ✌🏼

• 
  @aguitars3 ай бұрын

  Would love to see the same pressure test on finished necks since the wood and reinforcement make the total package.

• 
  @dr.wild53713 ай бұрын

  Perfect amount of time. If a person can't deal with important info to teach something that is very useful they shouldn't be watching in the 1st place. Let them learn the hardway and wishing they had watched this the 1st time and did it correctly. If they had want to watch short uninformative videos they deserve to get problems and they will with anything that requires attention span. They probably shouldn't even be playing guitar, it takes attention and time to learn.

• 
  @fabioribasdeoliveira72213 ай бұрын

  Eu tenho uma pergunta. Com essa máquina é possível cortarmos canos de latão de 1/4?

• 
  @Studio-ffft53 ай бұрын

  Great comparison and very informative. Technically, you are measuring load at a specific beam deflection. Since the cross-sections of the beams you are testing differ from sample to sample, it’s not quite a pure analysis of the strength of each material as much as it is a comparison of the beams with the predominant factor being the difference in strength of each material plus the geometric effects. One nit is that you are measuring load, which is in pounds and this is not a pressure but rather a force. Hope this helps and thanks for your analysis.

• 
  @kevinmackfurniture3 ай бұрын

  I watched the whole thing... Every minute. 🤘🏻

• 
  @jimw5443 ай бұрын

  This saw is no longer available. is there another you would suggest ?

• 
  @willieboy87983 ай бұрын

  i could find any mojo, so i settled for coffee instead....? edit is that the right joe???? jo now imconfused....

• 
  @KnottyBurlWoodworks3 ай бұрын

  Do you have project plans available for purchase so I can build one?

• 
  @claudenobles7793 ай бұрын

  I like the tool but don't want to sit there and pull it through the other side ... Is an "auto feed/advance" available? Subbed, Belled, thums up. Thanks

• 
  @rjhalsey3 ай бұрын

  Never mind, I just heard it on your video. My Bad! lol

• 
  @rjhalsey3 ай бұрын

  Where do you get the heat activated dry ink transfers made?

• 
  @maximumguitarworks3 ай бұрын

  ScaryCreative(.com)

• 
  @brianboudreau29663 ай бұрын

  You are the greatest example of how detail is so important, just watching this video shows your experience. Thanks!

• 
  @VinodJadavani3 ай бұрын

  good ok

• 
  @alexandermikoyan91713 ай бұрын

  Subscribed!