ECO-LAP Studio is KZread channel dealing with carbon fiber and epoxy resin.
I am gonna make various things, using these material.
Let's go for DIY with me!
Please Subscribe!! and Like!!
If you have any question, please e-mail to me.
e-mail : [email protected]
Пікірлер
Enabling ironing with a 25% flow would have given you flat top surfaces. This would just leave the vertical faces needing sanding.
And a Legend was born.
Fantastic!
It would have been easier just to carbon fiber wrap the original part if that's what you wanted but looks because you're not saving any weight
How did you not use any peel ply or breather cloth?
Love the well timed gifs 😆
Ни чего не понятно, но очень интересно! 😅
pressurize the tube, ditch the bag
Azimle sıçan mermeri deler 😂 tebrik ederim 🥳
use a good vacuum I use bike tubes no vacuum
I have an Audi I would be interested in buying one of these if you are interested in making another
So you started just from a old unprepped wooden countertop?
You failed a lot of time’s but you keep counting !! That’s all that matters
Thumbs Down for not showing the measurements of the resin and epoxy
bu çalışma kesinlikle amatör değil. Bravo çok güzel iş çıkarmışsın. Birçok emek sonunda güzel bir final olmuş
Has un video de como hacer un casco de soldar 💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀💀
열에 의한 수축또는 변형에 대한 부분이 궁금합니다
You had the pipe what is reason to scan it? A mood could have been made from the actual pipe. I’m sure I’m not only one who thought that.
If you only had one part and you would like to make a mirrored copy, how would you do it (without a CAD model)?
Vacuum pumps are not that expensive....
Its cost 700usd
Действительно перехотелось делать это своими руками
XD bez sensu
Neden 3d yazıcıdan spoileri yazdırıp üzerini karbon fiber kaplamıyorsun😂?
Nice work. +1
Sehr geiles Video...unterhaltsam und informativ! Vielen Dank dafür!
how many CC's is that Freshield vacuum?
日本語ですいません、質問させて下さい。カーボンを切った時肌に刺さらないのですか?
여름에 외장 파츠 스키닝 만들때 레진 으로만 마무리후 장착 하면 안되죠 ? 1k 2k 클리어 페인팅 차이점은 뭔가요 ?
超費勁…….
This is Carbon fiber ASMR
great video,but where is my Mpower
sucksess ;)
Cara membuat itu semua bagaimana? Dan alat apa saja yang harus diperlukan?
Hi eco lap big fan of your work. I wanna ask where do you get the pcb board in this video? And can you share your 3D file for 3D printed mounting base? Thanks!
What about the 2 transponders on the oem board?
4:56 Three coats of resin every two hours? So every two hours you apply 3 coats totaling 6 coats? Or 1 coat every 2 hours totaling 3 coats??
Why so many layers (legit question)?
nice job, thanks for sharing :-)
Most annoying video I've ever watched
No mames compro un laboratorio ….😂
*Dude is flexing how rich he is by overcutting that piece. I'm poor, it would have been about 4 in wide and 1/4" longer than the piece, lol.*
Transponder? How put?
Чуть чуть портит вид перепад толщин между карбоном и алькантарой
kzread.info/dash/bejne/q56kxMiOnK6bY84.htmlsi=AGgbHN2K89xK7kXY
Amazing work! I do wonder is this what you do for a living?
еще одно бесполезное вмдео где ничего не обьясняется, видимо кто то украл голос у автора
Very impressive workmanship 😎👍
I work for Motorieep I give you our secret technique : use PVA 3d filament, lay the carbon on the printed part, put the part in water. PVA filament disolves, then you get the carbon fiber part 5min later. Of course you need to accurately determine the offset!
카본직물은구하겠는대 저 접착식카본을 못구하겠어..누구아시는분있나요..?