Your videos are fantastic. Those handle covers look great, too!

That looks very impressive. Thanks for the good how to- guide!

That surface finish is incredible!

love the improved steps like the vacuum bag inclusion and doing the layers much faster i would also recommend use of either a heat gun, blow torch, or a spray bottle of acetone to help prevent as many bubbles on the surface in the future :)

Professional work ❤

I really need to admire your dedication to this. The amount of work you put in to every part is mind boggling. And the results look nothing short of amazing! Respect!

@yourmother9246

Жыл бұрын

Agreed. A stellar presentation indeed👏 Super helpful for sure. Definitely clears up alot of wonders.

One tip for the vacuum bag: get it to around 70% of the air out and start to use a squeegee to remove any air pockets above the carbon to get a mirror smooth finish. Than suck more air out -> squeegee air pockets -> and repeat till there are no more air pockets on the carbon surface. Also Mylar sheets over the last layer of carbon can give you a really glossy molding finish. After the vacuum, just peel the Mylar away.

@teoyota

Жыл бұрын

He is not infusing carbon with vacuum, just used it to push the weave neatly to the handles while the base cures.

대박..영상이 금새 또 올리셧다니 좋습니다 너무 좋습니다

Looks good. Nice and simple too.

Perfection as always 👍

Как обычно КРУТО !!! И формат видео класс-без слов, без лица и ВСЁ понятно при этом ! Круто! Красавчик !

You made this look way too easy! good job buddy

FLAWLESS VICTORY!

Amazing!!! What a finish!! Great to see such craftsmanship!!! Do you do this for a living???

Awesome !

This makes me want to order some carbon fiber wrap from Amazon now!!😂😂😂😂

nice job buddy as always

Incredible good job ! Nice !

seen other videos where torch is placed to the epoxy after coating to pull the bubbles, will help with the extra sanding

와..진짜 신의손이시네요ㄷㄷ;;;

Wow! Amazing results.

Excuse me, where did you buy your epoxy resin?

woooow!! thank you short and sweet. no family intro, no meet the dog,

THE KING HAS GIFTED HIS SERVANTS WITH CONTENT!!! ALL HAIL THE KING

Super résultats, la finition est magnifique...🙏

Gran trabajo como siempre amigo . Muy bonito acabado . Un saludo desde España .

Super Dope Vid SUBBED! Make me wanna try some of my old BEnz Interior Parts

That’s how it’s done 🔥🔥🔥

I would love to see you try a custom carbon or alcantara/suede airbag cover to complete the steering wheel look. Great work!

덱스형 필수시청 영상이다ㅋ

Excellent instructional video! I've been putting off a carbon fiber wrapping project for a long time, because it will be my first one and I've a bit of uncertainty how it may turn out. But your video just gave me the 'push' I needed to finally give it a shot! Mine will be the inside area of a headlight housing. It definitely has some curves that I'll need to workout but I have a spare/damaged one to practice on. There are a lot of bad things about the internet, this is one of the great things about the internet! Thanks for taking the time to share your knowledge with us. #subscribed

@walterheisenberg1013

Күн бұрын

I enjoy watching the manufacturing and conversion of parts to carbon fiber e.g. for weight reduction but what’s the point of wrapping beyond the visual effect? (Not to mention that it also adds weight) You could just buy carbon fiber wrap and get the same look with less effort

Mine are made of textured aluminium, how do you suggest preparing them before skinning?

우리나라 분이시군요 ㅎㅎ구독 하고 가요

Good work BTW

작업과정중 진공을 생략하고 진행하면 어떻게 되나요?

can you tell what kind of epoxy b are using? epoxy can withstand high temperatures or any type of epoxy. thank you.

So quick question would this method Work even though I have a different brand of epoxy resin

Eres un presumido y arrogante, pero sabes que te lo mereces, eres un maestro 🧑🏻‍🎨 en lo qué haces. Me encanta tu trabajo.

Question, is the vacuum bag necessary? I see some people leave the parts in the open and some in a vacuum bag. Are results different? Thanks in advance!

bro, can we use the resin as the glue instead the gelcoat?

Good job 👍

how much thickness gets added to the part this way? I'd really like to skin my interior trims on my e63, but I am kinda scared if it will add too much height to the part and imbalances the optic of the parts. is it more than 1mm?

새해복 많이 받아 형

저도 몇년전 자전거에 미쳐있을때 카본류를 정말 많이 봤는데 혹시 UD카본도 만들 수 있나요?? UD카본도 보고싶어요!!

Where did you get that vacum bag for just a vacumcleaner rather than the full vacumpump setup.?

Will this still work if I substitute the monster cans for red bull cans?

what can I use to replace the vacuum sealant thing?

Good job

Hello! Could you make a video on how you made your vaccum system? And also the container where you put the hand pump system! It would be great

excellent 👍👍

Can I ask you where you buy the carbon fiber locked wet lay ? Not the prepreg

초반에 에폭시 겔코트 바르는 이유는 카본에 점착이 없어서인가요?

Love it! Going to be doing my walnut interior on my G-Wagon this same way! Thanks for the video!!!

Somebody has been watching street bandito! Cool videos! Looks good!

In the end, the handles are heavier than the original ones. Very clever!

8 ай бұрын

That was for aesthetics only, bro.

@reygarcia3058

22 күн бұрын

Yeah only a few grams. Nothing noticeable.

This is Carbon fiber ASMR

허리는 많이 괜찮아지셨나요?새해복 많이 받으세요🙂

오랫만입니다!!

Hey ecolap why don't you make a forged carbon fiber trunk for your bmw?

This DIY video looks good but inside the car temperatures get 220 degrees or more on the hot summers days and the bond may fail ? So I would try a test piece 1st or get technical data.

really cool

카본 DIY에 도전해 보고 싶어서 알아보는데 레진이나 카본 원단은 어디서 구하는게 좋을까요...? 처음부터 대용량 구매하기도 어렵고 이지컴포짓보니 이건 배송비가 25만원이나되서 국내에서 구입해야 할 것 같은데 추천해 주실만한 곳 없을까요?

멋집니다

what wipes do you use?

I ran into a deep problem so I do all coats. It gets to the sanding part and it looks like I have pin holes , with sanding doesn’t seem to go away .. what should I do ?? I used heat gun to get rid of bubbles .

구독한지 몇년 됬는데 처음 댓글남깁니다 카본작업은 취미신지 직업으로 하시는건지 너무나도 궁금하네요~

Nice👍

Można wiedzieć skąd zamawiasz włokno w rolce ?

What epoxy do you use ?

유익한 영상 잘 보았습니다~^^ 영상에 사용되는 에폭시,카본 등 구매 사이트 알려주시면 감사 하겠습니다~^^ 압축 작업 할때 어떤 재료를 구매해야 하는지도 알려주시면 정말 감사 하겠습니다~^^

finally new videoo

Как всегда в своем духе 👍👍👍👋👋

Hey, amazing work, Im really impressed of how perfect your crafts are. Can You tell, what type of carbon fibre did You use for that product? I mean the thickness and g/m2. Also would be nice if there would be info about that for each video. Probably would help many amateurs trying to make something watching Your work step by step. 😁 Great work again!

@Marakeshh

11 ай бұрын

just use 200 or 245g/m2

Would you be able to do trim for my Mercedes?

I wrapped mine with 3d vinyl in under 40 mins and result looks the same :D

Bro what was the wizardry with pulling the fibers out before cutting. That was slick. I would probably f%^* that up lol and end up with a tangled mess

Esa resina es como la que se usa para hacer cuadros fotos y todo eso o es otra resina

chegou ao nível de perfeicao da peça

금손 ㄷㄷㄷㄷ

Hello how to do mix quantity ,epoxi resin and hardener persantage ,1 qt epoxi and 0.5 hardener ? Please say to us😊

Can you Bumper from car..?

Can i use redbull ?

Great! How about the plastic surrounding of the door handle? This could be next...😊

진짜 디지네요

4:56 Three coats of resin every two hours? So every two hours you apply 3 coats totaling 6 coats? Or 1 coat every 2 hours totaling 3 coats??

차가 주인을 잘만나서 호강하네요 ㅋㅋ

How much do u sell them made already

where to buy in europe all that need for?

What is the grammage of the carbonfiber material?

Why did you put gel coat, not a resin?

Prepreg?

You should use a good 2k glue for the bond to the plastic. Epoxy doesnt stick to Plastic all that well and the Deltas in CTE will have your parts settling and coming loose in the summer. Regards

@6stringer301

Жыл бұрын

Do you have a suggestion for the glue?

@morthskarampouzouklis8561

Жыл бұрын

@@6stringer301 Try spray adhesive

@6stringer301

Жыл бұрын

@@morthskarampouzouklis8561 thanks. I've tried 3m super 77 and 90. Both do not last long in Florida summers and the carbon layer delaminates from 3D printed ABS.

다음꺼는 언제 나오나요

Anyword on how its holding up?

Do you know turksıh language?

When is the next video release!?

ASM for BMW enthusiast 💪🏾👍🏾

Hi, any advice on not being confident with my own pieces ?, I always try to make them perfect, but always have minor details and that frustrates me a lot

@nikolamaric588

Жыл бұрын

dude this is normal, i love to do my stuff perfect but i know where i do the mistake. then i look at other how they do it and its more shit then mines. donth bother you cannot do everything 100% good

@ECOLAPStudio

Жыл бұрын

Hello friend The most important tip when skinning carbon fiber is not to apply a lot of epoxy resin at once, but to apply thinly several times. You don't have to worry about air bubbles when you apply epoxy resin thinly and sparingly. Also, it is easy to level for smooth surfaces.

Vous la trouvez où votre fibre de carbone?

I have one question, do you use the gelcoat as the first layer because you are part of plastic for better adhesion?

@ECOLAPStudio

Жыл бұрын

Hello friend Gelcoat has a higher viscosity than resin, so it does not flow. Due to its high viscosity, the carbon fiber adheres well if an appropriate amount of gel coat is used. Also, if the base parts are not black, the original color can be covered with gel coat.

@mitshylebrun2205

6 ай бұрын

@@ECOLAPStudiothat black stuff you used what’s the name?