Пікірлер

• 
  @mynew402211 күн бұрын

  Thank you for the video! I want to know if it’s possible to wire an external sensor to detect the presence of something ?

• 
  @mynew402212 күн бұрын

  Can we add an external sensor to detect the presence of a block ?? Thank you

• 
  @mynew402212 күн бұрын

  Thank you for the demonstration, this robot is so good. It motivates to have one like this on the desktop.

• 
  @eddrm46852 ай бұрын

  How is everything? Hope all is well with you and yours. Looking foward to seeing your Fadal up and making chips.

• 
  @Cysei-oj4cw2 ай бұрын

  hola donde puedo conseguir el manual que estas usando si lo puedes compartir estaría muy agradecido Gracias

• 
  @markrobirds79843 ай бұрын

  My Fadals have a cabinet that houses a spindle chiller with its pump and reservoir for the Dow Frost where you mounted that skimmer. They are all 10,000 RPM spindles and maybe that is the difference. It just looked strange to me not to see one there.

• 
  @danielrogers60905 ай бұрын

  Your a badass buddy, thank u sooooo much for your fadal videos. I really love my machine but its tired and needs work. I cant afford a new machine but thanks to you're videos i dont think i have to

• 
  @vileCR9995 ай бұрын

  This was awesome. Man I really want an old Fadal! Work has an old vmc20 and it's just so damn reliable!

• 
  @jaredfaustino64935 ай бұрын

  question:: does the encoder need to be clocked?? i just purchased a new encoder this morning and should get it by the end of the week. thanks

• 
  @sto27796 ай бұрын

  5:59 - Where does the oil come from? When using flood coolant is oil used too when milling? Thanks.

• 
  @paulboon22856 ай бұрын

  Hi! Just subscribed! Thanks for the video. I’m liking to have a machine at home that needs a RPC. How many amps do you have going to the house/garage? Did you have to increase it?

• 
  @AviationAutomation6 ай бұрын

  Thanks for your hard work with the video...not sure if you're still doing your offsets this way as its a old video but there is a way less complicated way of doing it. Use the haimer to set your offsets directly and use a cheap 2" dial tool setter off the vice or table. Use your Haimer first to get your height with the 2" block off your vice and table and record those numbers...mine off the vice is -7.996" or something. Then when tool setting and it asks guage block just enter that -7.996". Fixture offset will be direct reading from your Haimer no need to mess around with Macros. I also never move the axis control knobs or step knobs...I always leave the rotary in Z and the steps at max. that way you have a bit of a safety buffer when you enter jog mode and have forgotten to move it back to Z...Just use x, y, z on your keyboard for axis control and H,M,L for step size...

• 
  @Freetheworldnow7 ай бұрын

  Good move!!! This is a real serius machine with way more capacity. Your production rate will be double if you machine steel. The biggest drawback is the spindle rpms not so high and the outdated electronics and control. But you will be able to make some improvements as you progress.

• 
  @alejandroleal228 ай бұрын

  I still don’t know how to add usb drive program into the panel

• 
  @user-jh7tk2fr3w8 ай бұрын

  requerimos el manual de una cnc, veo que tienes el original, a nosotros nos dieron unas mugrosas copias con imagenes ilegibles y una pesima traduccion al español, te pido por favor me digas cuanto cuesta un manual, la empresa de fadal en mexico ya no existe y no tenemos soporte tecnico

• 
  @kduzick9 ай бұрын

  When checking backlash you need to be checking along the travel of that axis to see the wear at different points along that ball screw. The way you appear to be checking Y is by moving X which is only going to show you the backlash at one point in the ball screw

• 
  @user-ch5zy5rm5r9 ай бұрын

  Thanks much for the great series of videos . . . it's been very helpful in setting up our 'new' VMC15. Any idea where we can get a pivoting table like the one you installed on the bottom of the control box in this video? I"ve been Googling around and don't even know what to call it.

• 
  @megacanam9 ай бұрын

  My X axis is vibrating badly like it cannot resolve where it is. The resolver has the correct 1.7vac at the bullet terminal, and is silky smooth bearings. I took the resolver apart and the insides look factory fresh. I'm stumped, guess Ill replace it.... but wondering what the next part I'll be throwing at it, as I dont think this one is malfunctioning.

• 
  @iexcedo69189 ай бұрын

  I cannot express how thankful I am for these videos. These prehistoric Dino machines. Have drove me crazy at work

• 
  @billshiff20609 ай бұрын

  Why do you think you need that expensive whizz bang contraption to do your work? Machinists have been doing ultra accurate and production work for 200 years without that thing.

• 
  @phil20829 ай бұрын

  Every Fadal Ive used has "Go to last home position? Y/N" and I have always hit N, because it goes somewhere random and sets that as the nrw machine zero. I figured out how to stop this. Go to the actual home position, hit N for this prompt, then type into the command line "SetCS" for setting the cold start. None of my machines prompt me for another home position when I start them now. Helps save some time.

• 
  @ScottHamilton-ys2cm9 ай бұрын

  Great video! But just for future reference, the springs you referred to as bevel springs, are actually called Belville Washers, and how they are stacked can vary from application to application.

• 
  @johntre76569 ай бұрын

  I'd be interested in a kit. Don't have a kill to help with parts so a fully off the shelf solution is definitely interesting!

• 
  @ScottHamilton-ys2cm10 ай бұрын

  If you bought your level from MSC, you're not a cheapskate!

• 
  @enriquenaranjo341210 ай бұрын

  Buen día buenos vídeos una pregunta tengo una Fadal 2216 1997. Al apretar el botón verde no se oye el chasquido al principio si se oía A veces si y a veces no podrías orientarme que puede ser ? Gracias

• 
  @RafaelHernandez-sp8gy9 ай бұрын

  revisaste los fusibles y demás?

• 
  @enriquenaranjo341210 ай бұрын

  Buen día buenos tus vídeos una pregunta tengo una Fadal 2216 año 1997 En el eje Z. Cómo que no responde muy bien el husillo cómo que no gira bien Me podrías orientar algo porfavor gracias

• 
  @TheMoody87611 ай бұрын

  Ive been looking at one localy how do you load a program? I currently use fusion 360 on a brand new machine at work but im wanting to get a fadal for home use

• 
  @bgwmachine11 ай бұрын

  I use an FTP server. You could also use USB or SD … both require a board install but I cover it all in another video I made: kzread.info/dash/bejne/e5mM1Lueoa7AoNY.html

• 
  @billyhickson163211 ай бұрын

  Hi, would a 5HP rotery Three Phase Converter be big enough for a 4.4 KVA EDM machine ? Thank you for any help.!!

• 
  @billb29511 ай бұрын

  what "clear" coolant are you running is it Blaser Synergy 735? Ive been running it in my Tormach and for the 1st year it was fine, now all the paint is pealing but I cant say I did not know the issues others have had with the 735 so I guess I'm now paying the price. I hate oil based coolants is yours non oil?

• 
  @dylanw6393 Жыл бұрын

  Very helpful videos, thank you. I just got 3 vmc15/xts. Same here, used to Haas, mori, even had a tormach. Fadals are just a little weird/older/different. Fyi fadal newbs..g54 is 'e1' . I was sooo confused when my g54 didn't show after post processing😊

• 
  @piotrsobczyk8691 Жыл бұрын

  Hello Mr thank you for this video. But i have problem. I push manual Then spacebar Then custom macro but i have diference manu only some opitions with programm (change program itc) and why? Sorry for my poor English i'm fadal from Poland;)

• 
  @pwnrar Жыл бұрын

  I've really appreciated your Fadal videos as I was getting my 15XT set up. I fired it up successfully for the first time a week or so ago and am getting close to making chips! I just wanted to say that your attitude in this video is really inspiring. It seems like you've had a lot of change in your life recently, some of it seems quite challenging, and you seem so upbeat and positive in the way you're approaching it all. I was very happy to see in the comments that you've still got the Fadal tucked away for when you've got the space again. Congrats on the new job!

• 
  @allanholm5968 Жыл бұрын

  Thank you, I am very happy with your videos. i just bought a fadal vmc15 so you help me thank you very much 💪👍

• 
  @jimd68 Жыл бұрын

  Thanks for the video, well done, this will help me a lot. I’m just getting started on a Fadal.

• 
  @auxpower13 Жыл бұрын

  Good stuff, Bro. At first, I thought this was like the Smithsonian Channel when I saw that mill. Just busting your chops. I subscribed so let's get it on with that Fadal. Thanks for making a video of getting that rotary converter going.

• 
  @drmutus Жыл бұрын

  I was actually pretty disappointed with my purchase from Elephant Robotics. I purchased the MechArm 270 M5. They didn't have as many resources to get things working.

• 
  @makerspace533 Жыл бұрын

  I think the answer would be to use a dedicated 3/4" end mill holder and calibrate the Haimer in that holder. Then never remove it from that holder. ER collets are good, but not perfect.

• 
  @georgehunter4023 Жыл бұрын

  Fadal would not ever be a candidate for me after 34 years in the business and running nearly ALL brands over the years. The worst boat anchor I've ever seen. First one I ever ran was complete pile and company called Fadal to come get their crap out of our building ASAP but there was no longer a company left to return it to. Kept it without making further payments for 5 years then scrapped it.

• 
  @ryankingston7733 Жыл бұрын

  Thank you for your comments and input, what brand of machinery would you recommend for a new shop owner's first machine?

• 
  @drewgraff7748 Жыл бұрын

  I just prefer to set toolheights off top of vise jaw. Then measure from top of part to top of vise jaw and boom, that’s your z offset. No need for anything fancy…

• 
  @naybortfm6531 Жыл бұрын

  You spend 20 minutes talking about your tools and then you speed up the important part? This guy is an idiot..

• 
  @keal4825 Жыл бұрын

  Thank you so much

• 
  @vinodgopivlogs6986 Жыл бұрын

  Nice nice job

• 
  @robertalbold751 Жыл бұрын

  Thank you, that was very helpful.

• 
  @varunnand6065 Жыл бұрын

  the robot arm hello world program 🤣

• 
  @fardinkarim Жыл бұрын

  thanks I am working with this for my final year project and this was really useful to get a basic understanding of how to use it!

• 
  @edgarcastaneda3945 Жыл бұрын

  Hermano muchas gracias por la información saludos desde México

• 
  @hieuhuynh842 Жыл бұрын

  I’ve got the same problem, my 3D Haimer taster drop from spindle twice 😢 due to assembled wrong pull stud, now it shy 0.12 mm ( around 0.005’’) error on X and Y axis with new needle. I saw your link forum and try but it not worked. I’m really appreciate if you help me with your experiment fixed your sensor, thanks

• 
  @marcgilbusquet1878 Жыл бұрын

  where did you buy the parallel rectangular blocks?

• 
  @LazuliteLol Жыл бұрын

  this isnt command and conquer...

• 
  @urielsanchez6279 Жыл бұрын

  Hello friend, I have an American rotary converter with a 5.5 hp motor capacity. I have a problem, I don't know what capacitors it has, since they were damaged, could you help me?

• 
  @urielsanchez6279 Жыл бұрын

  motor es de 7.5 hp