It all started as a joke. And now its a reality and something I'm truly passionate about. I love sharing knowledge in the electrical field. Providing some insight to the electrical side of jobsites. Every once in a while I throw some jokes in so everyone knows life is about having fun! Enjoy what you do. I appreciate the support I continually receive!
Пікірлер
I miss the days when these guys used to hate this music 😢
I thought we were gonna get a “so I became an electrician”
All open shop guys are pussssssss
Gray pipe for wire. I think it has to be deeper in the ground
I just use snap in bushings. Cheaper and faster
This is exactly what I needed, thank you!
Where is the faceplate cable??
The neutrals and grounds are bonded at transformers🤣😅
Bro its 2024. You should have a lot more AFI in there.
Can you use 8/2 romex over 50 feet?
takes more than tools. peace, trust
maybe to hinder tampering?
SNL, timothy chalomet. pete.
Believable. Seen IRL: Some people respect. They don't do messy work and they don't leave a mess.
Show us how bad the crimp is.
Bring on the stripper vid 😸
I learned this in kindergarten with those plastic chairs 😂
Instead of those shit metal romex connectors can we use either plastic buttons/T&B connectors
Do not do this you cannot modify fittings like that.
Awful instructions.
I've done the same shit, but I wouldn't post it. Kind of like posting about getting a bad test score and acting like it was good
What would we do without the reciprocating saw and the accurate measurement of close enough .
most panels i’ve worked on just have a main right in the panel. Honestly wish they had separate disconnects like this. Would make doing a panel swap without a permit as an apprentice a lot easier… Wouldn’t need to pull the mains out of the panel while they’re still hot.
😮 you're a pro with those nuts 😂
Like the spreadsheet.
Well I have used that bender, a few times, even at my size it can be rather difficult. I’m 6’7. After a while, you just say, they hell with it and get the 555 out, and you’re done.
I did all of this and still the lights aren’t working
Yep definitely how electrician’s do it.
Good 👍
Jack-leg install
That looks really good. Been doing electrical work for 30 years and this is my first tape light install for under cabinet lights. lol my situation is a new home build so luckily no drywall. lol
What size wire do you run for the tape light. 18 gauge? I was gonna use 16 but I think that may be larger than I actually need. Short run... less than 25 ft of tape light. Thanks
where do those wires coming into goto
That staple gun is junk. It died out internally after doing one rough in.
What laser are you using for this?
Yo dude I started an apprenticeship with a small shop recently. They are using scrap romex jackets as straps when roughing, what’s your thoughts on that lol? As a green apprentice it’s one of the first things I was like uhhh wtf is this?
I wana see the pipe how it came out
With your sense of humor and informative insight..... You earned another subscriber
start with your hands higher it's not hard at all
Little more detail maybe next time please it was fast but good video
Wow very helpful thank you so much
The difference between a worker and a professional
How it looks is everything perfect
Is that a 1 inch K/O?
Bro slid on a lot of pipes in life before finally achieving his dream.
19:40 dude is capital Lame! Her business is her business dudes like him deserve to be dogged! Because they pass those signs
None of that worked for me
So close
Thank you 🙏😭I put taquitos in the microwave and chicken in the toaster (oven) and it overloaded 😂
There are far more than 2 types of wire connectors. Basically you want a good mechanical and a good electrical connection. Evaluate alternatives accordingly.