Пікірлер

• 
  @socalob7 күн бұрын

  Was your harness that clean when you pulled it off or did you wash it? If you did what did you wash it with? My truck harness is full of grease, oil and a ton of dirt. Not to mention the wires feel as if they are stuck together lol. Great video, I really appreciate it!

• 
  @ronniecarroll2028 күн бұрын

  What fuel cell is that? Stock? I’m in the middle of an ls swap on my 01 ext cab and want to do my exhaust the same way. Great job btw

• 
  @motherloverjones600815 күн бұрын

  great job, Clarence !!

• 
  @DaInfamous0ne19 күн бұрын

  Is the 4wd frame the same as a 2wd?

• 
  @Philhanak25 күн бұрын

  A light would be nice

• 
  @MrJackson66Ай бұрын

  Did you ever finish the "stand alone harness" ? To be a stand alone harness it needs a fuse box and some relays hooked up... Its a nice start .

• 
  @Chicagomoney862 ай бұрын

  Thank you 1 million you have gave me more confidence to proceed on my LS swap and do it myself.

• 
  @wingrider10042 ай бұрын

  I'm restoring a 72 Ford right now and I can appreciate all of the hard work you put into that frame. Good job.

• 
  @Dboyquicks102 ай бұрын

  That t56 is going to be awesome. I've been thinking about putting one in mine. Definitely feel more confident about it now. Thanks brother.

• 
  @centralscrutinizer763 ай бұрын

  I got a 4.3 , the harness and pcm came with the motor and was cut in pieces , i rewired it with wire I bought off ebay . After a couple or months the motor wouldn`t start , i had been using the wire on other projects ,they were failing too . The cheap ebay wire the copper conductor turned to green dust not just the connections ,but the entire length of the wire .

• 
  @jbonzmcgee3 ай бұрын

  "..I live in a constant state of unfinished projects. " .. you and all of us brother.

• 
  @p.b.sHUNTING3 ай бұрын

  Pretty neat setup, but not having access to all the shop equipment…. I think I’ll stick to the plan of swapping to 98+ Blazer spindles.

• 
  @Jamestfarrell4 ай бұрын

  So, I understand that this harness mod makes it possible for the LS engine to be dropped into, say, a bare-bones 1949 Studebaker truck which has been converted to 12V Negative ground? Help me out here!

• 
  @Jamestfarrell4 ай бұрын

  And as soon as you label them, BEFORE you unplug them-take a cell phone photo!

• 
  @bradleyyates84154 ай бұрын

  Any chance of you changing out the 3" exhaust yet, would be interested if you have.

• 
  @internallycombusted14 ай бұрын

  I am swapping to blazer rear disc and c5 front brakes. I'm trying to figure out what master cylinder to use. what master and prop valve did you end up using?

• 
  @mnice594 ай бұрын

  I might be treating this like a redit page but honestly what did he do here? He referenced the web page that told him to remove these wires but I dont get why. I incorrectly thought he was going to create a NEW wiring harness with new (non brittle) wire.Its obvious that if he was putting it in a same vehicle hed need the same wires so I assume its other than that. How would this website know he didnt need these wires?

• 
  @MikeY77z284 ай бұрын

  Hi Tommy,I'm new to your channel.I really like the content.Very cool s10 Sorry about the accident.

• 
  @Countrytimesgarage4 ай бұрын

  What throw out did you use?

• 
  @billyrector35784 ай бұрын

  Great Job sir I Like your work

• 
  @_BaguetteDoggo5 ай бұрын

  my 93 2.8 5 spd has this same plastic fender kit, but its like i cant find out where it comes from..was it a factory option or what?

• 
  @samrapheal18285 ай бұрын

  Mucho gracias...Thank You💯

• 
  @p.b.sHUNTING5 ай бұрын

  What state are you in? I’m in SC and just purchased a 96 s10 2.2/5spd for my son and I to tinker with. I have a complete drivetrain/harness/computer from a 96 full-size (5.7/4l60e) but I’d rather have manual trans in the s10. I have no problem with the mechanical side but the electrical blows my mind.

• 
  @3TLM6 ай бұрын

  Question where can I find a shop that would do this a lot of us garage mechanics don't have this type of equipment or y'all manufacturing the hubs

• 
  @alvarovillalobos39586 ай бұрын

  What year Camaro rotor is that

• 
  @terranceh53446 ай бұрын

  Dude thank you so much for this video. I’m building a very similar setup and the parts list was a godsend.

• 
  @user-qz7vt3xq7g7 ай бұрын

  What type of motor mounts are you running?

• 
  @tommyhajimoto69687 ай бұрын

  Can that section be cut completely off and replaced with something removable? I don't feel like taking the whole motor out to replace a oil pan gasket Any links would be great. Also would it be safe to do?

• 
  @efrainsantos81887 ай бұрын

  Greetings.. I am in a project for a 1984 S10, I will be installing an Ls 5.3 and I would like to know what engine mounts I should use for this project.

• 
  @Vile_908 ай бұрын

  im not sure if its been asked before, but what seats are in your truck with what mount? those look nice

• 
  @darrenporsch8 ай бұрын

  I'm kind of confused why couldn't you use the two wheel drive Blazer spindles that all the guys from the g-body is used to swap in bigger brakes

• 
  @NotaRobot_gif8 ай бұрын

  How's it held up?

• 
  @zepa08409 ай бұрын

  How did you get the stock motor mounts off? How did you get access to the nuts on the end of the motor mount bolts that are under the frame?

• 
  @user-kd6dv4iy7z9 ай бұрын

  What kind of big break kit is in the front of your s10, i cant find a kit to fit in the spindles

• 
  @robertapplegate60469 ай бұрын

  Do u have a pdf file for the brakets you cut out on the plasma table

• 
  @user-ki4go4oq7m9 ай бұрын

  They make a kit for the S10 now. I bought 1 but havent installed it.

• 
  @GIITW.5OKC9 ай бұрын

  Are you at all worried about the displacement of the master when running a different slave?

• 
  @ricksteelcustoms31969 ай бұрын

  Don't take this as an insult but you look a lot like my favorite "Stooge" Jerome Lester Horwitz, known professionally as Curly Howard. Thumbs up for that alone! 👍

• 
  @626foo9 ай бұрын

  Hey cheeky what kind of lathe setup did you use for the hub? With my lathe machine I feel like it’ll take me days before its cuts it to size! Please sum insight i knows its been awhile

• 
  @chrisholden295210 ай бұрын

  Just kinda curious did you get it finished yet? I'm new to your page. Just bought a 84 myself. Looking for inspiration.

• 
  @jaivette10 ай бұрын

  Nice job

• 
  @jaivette10 ай бұрын

  Nice clean shop, Lov the floor coating

• 
  @PeterHatch-mx7zc10 ай бұрын

  May be i missed it how many gallons please

• 
  @PeterHatch-mx7zc10 ай бұрын

  How many gallons is the tank please

• 
  @CHUYITOMCFLY11 ай бұрын

  Hello brother, how do I get the headers, do you know part number?

• 
  @jessemitchell36493 ай бұрын

  they discontinued them now

• 
  @raystevens68711 ай бұрын

  What year is your Corvette engine. Because it seems to me that the aircondioning compresser should be on top of the engine. My good friend had a C4 Corvette and that's where his aircondioning compresser was.

• 
  @jessemitchell36493 ай бұрын

  That's because C4 Corvettes still used a Gen 2 small block, not the new style LS small block. Most LS engines use a low mount AC compressor

• 
  @raystevens68711 ай бұрын

  Hay don't forget about the cast Iron headers.

• 
  @user-kn5wz5gu3t11 ай бұрын

  As an experienced builder of these lil baby trucks w/ over 1000hp .sorry about your crash ! Might I suggest more frame structure, I've twisted 6 of these S10's .Nice craftsmanship

• 
  @carsnstuff192911 ай бұрын

  Very helpful. Subscribed

• 
  @s.encode11 ай бұрын

  Buddy, We would like to arrange to have our LED lighting shipped to for doing a product review. Is there a way to reach out to you?