Building Three Inch Stainless Exhaust For My LS1 Swapped S10
I'm EXHAUSTED!!! But I'm pretty happy with how everything turned out. Can't wait to hear this thing! Links to all the parts I used listed below
X-Pipe Kit:
www.speed-engineering.com/uni...
Black Widow Mufflers:
blackwidowexhaust.com/muffler...
Mandrel Bent 45s:
www.summitracing.com/parts/su...
Straight Pipe:
www.summitracing.com/parts/su...
Clamps:
www.summitracing.com/parts/wl...
O2 Sensor Bungs:
www.summitracing.com/parts/vp...
Exhaust Hangers:
www.summitracing.com/parts/wl...
Floor/Tunnel Shield:
www.summitracing.com/parts/de...
Muffler Shield:
www.summitracing.com/parts/de...
Cool Tape:
www.summitracing.com/parts/de...
Пікірлер: 27
Awesome to hear you're in atlanta, I'm in auburn alabama and about done with most of the big money purchases for my build which is also a s-10 including freshly build motor completely gone through by me and hoping for the best. If you still have gumby and have free time ever, I'd love to check it out
@bradleyyates8415
Жыл бұрын
I also saw in a newer video that you may go to smaller exhaust. If that were to happen or happened already, I'm interested in the 3".
Right on. Looking good. Battery box is a good idea.
@CheekyGarage
4 жыл бұрын
Thanks! I think it should work alright
Nice build thks for the video
Exhaust came out great. Coming along nicely.
@CheekyGarage
4 жыл бұрын
Thank you sir! Wish I was a little further along, but I'm happy with it so far
just "finished" my ls1t56 94 s10 2 days ago love the videos ....need to do a gas tank relocation may look into the blazer tank need to move weight around
Art work is a thing of beauty.
That thing is going to be one killer truck when your done. Keep up the awesome work.
@CheekyGarage
4 жыл бұрын
Thanks! I'm trying!
Great job, making better progress than I am on my s10.
@CheekyGarage
4 жыл бұрын
Thanks! It's a marathon, not a sprint!
Good stuff.
What fuel cell is that? Stock? I’m in the middle of an ls swap on my 01 ext cab and want to do my exhaust the same way. Great job btw
nice job so am planning to build the exhaust system in my chevy 1952 with s10 chassis so i notice you do not install any Cat Converter. would you tell me if install them or not makes more or less HP or more or less louder? and a cat converter are not required for the law?
Check you out with your ZQ8 added support on your frame
@CheekyGarage
3 жыл бұрын
It makes a great exhaust hanger mount
how did you remove the wire harness from the firewall so that you could paint the cab
A question please? "Back purging" is what exactly?
@CheekyGarage
4 жыл бұрын
It's simply filling the pipe with argon. Without a purge, stainless will "sugar" or oxidize the back side of the weld. It happens when a weld is exposed to oxygen in the air. Back purging allows you to get full joint penetration without defects
I’m swapping my s10 with a 5.3 what rear end and drive shaft are you running?
@CheekyGarage
4 жыл бұрын
I'm running an 8.8 from an Explorer that I narrowed, and I had a driveshaft made to my dimensions with solid Spicer 1330 joints
@ryanflores8309
4 жыл бұрын
Cheeky Garage thank yu! Siccc ride love how it’s coming together can’t wait to see yu finish it
What are you doing for the clutch.
@CheekyGarage
4 жыл бұрын
I went with the Tick Performance LS7 clutch kit
Speed engineering clamps suck I’m general