Пікірлер

• 
  @isaacvelasquez772 күн бұрын

  What is that connector on the ac line? 1:24 I have a loose connector not connected to anything

• 
  @JCTFIXITКүн бұрын

  Low pressure cutoff

• 
  @ItzMarcoz8 күн бұрын

  does it have a be a 20a add-a-fuse or can it be 10a?

• 
  @JCTFIXIT8 күн бұрын

  Ideally you would match the fuse that's already there and then the actual add a fuse circuit can be way less.

• 
  @ItzMarcoz8 күн бұрын

  @@JCTFIXIT does it have to be the ignition fuse or can it be another?

• 
  @JCTFIXIT8 күн бұрын

  It needs to be a slot that is only on when the car is on or you will drain your battery.

• 
  @ItzMarcoz7 күн бұрын

  @@JCTFIXITmy local auto parts stores only sell up to 10 amps. is there another fuse i can tap into that’s not the ignition

• 
  @noahkottmyer90998 күн бұрын

  What if my ign switch is a 2 amp fuse? Im sorry if this is a stupid question. Im really new to electrical and im just throwing myself into this job?

• 
  @noahkottmyer90998 күн бұрын

  I just looked and my cigarette lighter is a 20 amp would that work?

• 
  @JCTFIXIT8 күн бұрын

  The add a circuit has its own fuse. It doesn't need much as it's just the signal to tell the amp to turn on.

• 
  @JCTFIXIT8 күн бұрын

  You want to go off something that is powered only when your car is on. Otherwise your amp will stay on all the time and drain your battery.

• 
  @roncogan960415 күн бұрын

  My broiler works but oven (bake) doesn’t and gives error F-09. What is the issue in this case ?

• 
  @JCTFIXIT15 күн бұрын

  Did you watch the video?

• 
  @roncogan960415 күн бұрын

  @@JCTFIXIT yes, here is the problem: I ca “force” my bake function to work if I turn on the top gas burners, but I get F-09 if I try the bake function without the top burners. Can this be circuit board issue as well ?

• 
  @JCTFIXIT15 күн бұрын

  Sounds like you need to replace your ignitor.

• 
  @roncogan960415 күн бұрын

  @@JCTFIXIT ok thanks for the help. Much appreciated. I will try the igniter first and if that doesn’t work I will replace the circuit board.

• 
  @Snceday116 күн бұрын

  Big 3 upgrade is definitely needed and 2 gage or even 0

• 
  @JCTFIXIT16 күн бұрын

  Big 3 upgrade?

• 
  @Snceday116 күн бұрын

  @@JCTFIXIT KZread it.. you add a large o gage or big wire from your alternator to your positive on battery. Then you run a negative from your battery to the frame of vehicle and then you run a cable from engine block to frame of vehicle and by doing that you updated your vehicles electrical system which at that point you can have great safe power for running a audio system including subwoofers and amp... Because it's takes a lot of amps and it could kill your battery.

• 
  @johnjones-zq2uf20 күн бұрын

  No gasket

• 
  @JCTFIXIT20 күн бұрын

  Yes. That's is correct. I award you 10 points.

• 
  @johne671621 күн бұрын

  Great vid man, hope the baby is Okay?.

• 
  @JCTFIXIT20 күн бұрын

  She was fine just upset that mommy wasn't around.

• 
  @DannyGarrett23 күн бұрын

  Thanks I’ve been trying to figure this out so simple to fix.

• 
  @ClaraSilva-el3yrАй бұрын

  I have a factory sub in my trunk as well. I just tap the speaker wires between the amp and the factory sub? I would love to not have to open my dash. On my amps manual it says to connect speaker outputs from receiver to high level input connector of amplifier. I could go into my dash and do that?

• 
  @JCTFIXIT22 күн бұрын

  You could.....

• 
  @izh6421Ай бұрын

  Thanks for the video, I just installed a 75 inch tv with this mount and I noticed I can turn it left or right to make it level almost as if something was loose, do you know how I can tighten it so it stays level all the time?

• 
  @JCTFIXIT22 күн бұрын

  There are nuts that need to be tightened to ensure this. I would recommend some medium strength threadlocker on this nuts. When you get a big tv and you move it, it kinda acts as a lever on the pilot point making it harder to lock the pivot point down since very little force from the edge of your TV equals a lot of force at the central pivot.

• 
  @simonmears1726Ай бұрын

  Don't really need rtv on tranny should have gasket can use dab of rtv on corner s just too keep gasket from moving did my corolla no leaks 😂

• 
  @nolan3184Ай бұрын

  How did you find out which wire was negative and positive for the stock subwoofer in the trunk to connect the amp

• 
  @JCTFIXITАй бұрын

  Lookup your vehicles stock speaker wiring diagram.

• 
  @nolan3184Ай бұрын

  @@JCTFIXITI’ve looked everywhere and couldn’t find it so should I get a wire negative and positive tester?

• 
  @JCTFIXITАй бұрын

  You could What colors are the wires?

• 
  @nolan3184Ай бұрын

  @@JCTFIXIT the left side of the stock subwoofer has a black wire and a green with red stripes wire. On the right side of the subwoofer there is a yellow wire with red stripes and a red wire with blue stripes.

• 
  @JCTFIXITАй бұрын

  Year make & model?

• 
  @derickd2385Ай бұрын

  The key is hand tighten the screw until see the bead squish out just a teeny, after 1 hour then torque the screw.

• 
  @rackyshakАй бұрын

  Yooo, thank you! Helping my parents troubleshoot theirs and this seems to be the issue.

• 
  @ashleyhobby1070Ай бұрын

  Looks like spaghetti

• 
  @JCTFIXITАй бұрын

  I love italian food

• 
  @zachdent9112Ай бұрын

  😊

• 
  @baileegatton7767Ай бұрын

  Will my system work with rca to the rca converter to the rear left speakers wires? And what wire do you use to run the add a circuit? Speaker?

• 
  @JCTFIXITАй бұрын

  Your wording is a little confusing. Without knowing your setup, it's hard to say. Generally though on an amp, the rca inputs are for signals that are low and not being driven already. High level inputs are called such because they can handle a higher watt load incoming into the amp.

• 
  @skmmiranda1Ай бұрын

  Caution taking out the circular trap to the right of the drain hose can release A LOT OF WATER!!!

• 
  @JCTFIXITАй бұрын

  That's why you drain it first silly

• 
  @govolsfightvolsfight2908Ай бұрын

  Good high quality is subjective in this case. Please tidy it us, it's making my ocd act up.

• 
  @JCTFIXITАй бұрын

  Haha. I feel you.

• 
  @jeep198713 күн бұрын

  No one cares about your ocd

• 
  @KevinPratt-sg4ydАй бұрын

  Will this two battery setup provide enough power to run a fifth wheel?

• 
  @JCTFIXITАй бұрын

  If it is based on 12V battery architecture then yes

• 
  @TalkingHands308Ай бұрын

  I already replaced the front door speakers. Kind of torn if I should replace the tweeters first or the rear speakers... Which makes a bigger difference in your opinion?

• 
  @JCTFIXITАй бұрын

  Rear speakers IMO

• 
  @TalkingHands308Ай бұрын

  @@JCTFIXIT Ok, thanks!

• 
  @MOBU76Ай бұрын

  What if the screw is not there?

• 
  @JCTFIXITАй бұрын

  Then it is a different model or is missing the screw.

• 
  @CodyPexton1Ай бұрын

  Thank you!!!! Such a big help man. And good video. To the point yet thorough explanation. Thanks again!

• 
  @JCTFIXITАй бұрын

  Glad it helped you!

• 
  @JimmyLima715Ай бұрын

  Pretty sure all powered subwoofers automatically turn on and off when tied into the high level inputs to just one rear speaker needed. Why all these other devices and remote wires needed?

• 
  @JCTFIXITАй бұрын

  Some newer models do that. Many do not. Also you want both so that you get tunes from L & R channels

• 
  @ourv9603Ай бұрын

  I found my 6" GARMIN GPS fits PERFECTLY into the sunglass holder. I just need to tap that purp wire for key on power. !

• 
  @ourv9603Ай бұрын

  What that sticky stuff is is, FRICTION TAPE. 100 years ago when man first discovered electricity friction tape was developed to act as an electrical tape. Unlike the PVC electrical tape of today, friction tape has no adhesive it is just a little sticky to stick to itself. This is what our great great grandads used. I am amazed it is still around but I guess for whatever reason, Ford finds it necessary to use it here & there. !

• 
  @lesliegarneauАй бұрын

  Connector would not have a “shirt” in it. It would be an “open”.

• 
  @simonmears1726Ай бұрын

  Nice and clean both surfaces with razor nice bead around bolt holes mate together and nip up then tighten stop using gaskets on alloy sump s bit of a pain 😢

• 
  @wlightmanАй бұрын

  I thank you very much for taking your time to make this video, it helped tremendously, I couldn’t have done it without this video

• 
  @JCTFIXITАй бұрын

  Thanks for taking the time to let me know. It makes me happy to help others!

• 
  @andyhernandez9154Ай бұрын

  Wats that extra cable ?

• 
  @andyhernandez9154Ай бұрын

  Or plug I should say

• 
  @JCTFIXITАй бұрын

  The little red jumper?

• 
  @brandonconners66062 ай бұрын

  Amazing...had the code today, had no idea what it meant...stumbled onto your clip and it was a easy fix. Clogged pump! Very much appreciated, thank YOU

• 
  @JCTFIXIT2 ай бұрын

  I am so glad it helped you out!

• 
  @ashtonharvey57232 ай бұрын

  If your car has a factory amp wouldn’t that be playing low end from your cars amp into the amp your adding? Someone told me I shouldn’t do this but I don’t see really why not when I’ve seen others do stuff like this. My car has a factory amp that uses the rear 6x9’s for bass. Would it be ok if I do this on my car like you did yours? I’m guessing your car has a factory amp which means you tapped into the low end speaker in your car to give your amp an input from your factory stereo.

• 
  @JCTFIXIT2 ай бұрын

  People recommend not doing this because your amp can prefilter the frequencies for your stock sub that may or may not allow your new aftermarket sub to reproduce to its full capability.

• 
  @jaskarandhaliwal82 ай бұрын

  Where to hook the power wire if you don't have under the hood battery? Should I hook it to jump start connecter?

• 
  @JCTFIXIT2 ай бұрын

  If your battery is located somewhere else like trunk or under rear seat, just run it from there.

• 
  @Maddanju16322 ай бұрын

  Excellent tutorial and expertly explained. You were lucky that a speaker in the boot was accessible as mine are in the rear doors…

• 
  @JCTFIXIT2 ай бұрын

  Agreed. Good luck with your install!

• 
  @plus25792 ай бұрын

  dude this video was exactly what i needed.

• 
  @JCTFIXIT2 ай бұрын

  Love to hear that!

• 
  @seyuueueerenityahhhh2 ай бұрын

  So what if your vehicle is originally 24v

• 
  @JCTFIXIT2 ай бұрын

  Find a battery that suits you. 20v max from some applications should work.

• 
  @gtrance35672 ай бұрын

  I’m thinking about adding a powered subwoofer to my car trunk. I take it i’d follow similar steps you did? Also, it looks like you tapped twice into your speaker? Is that right?

• 
  @JCTFIXIT2 ай бұрын

  Yeah just to grab left and right channels you could also use rear speakers if you don't have a sub stock

• 
  @gtrance35672 ай бұрын

  @@JCTFIXIT thank you!

• 
  @natevalverde22212 ай бұрын

  Do the t taps allow the rear speaks to continue to play. I tapped in directly and now they don’t work is that why?

• 
  @JCTFIXIT2 ай бұрын

  You need to leave the lines running to rear speakers in place and tap into them to piggyback the signal.

• 
  @BarbaraBelcher-tn7cy2 ай бұрын

  thanks for the video Iam going to try this I will let you know if this is my problem thank you again.

• 
  @JCTFIXIT2 ай бұрын

  Good luck!

• 
  @user-sw5gz4to8n2 ай бұрын

  Thanks !!

• 
  @JCTFIXIT2 ай бұрын

  You are welcome!

• 
  @rebelalfa962 ай бұрын

  Homie ruins a fire wall seal not realising you can pop them out with a screw driver 🤦‍♂️

• 
  @JCTFIXIT2 ай бұрын

  Still gotta be able to fit a fat wire in there even if you pop it out.

• 
  @Igh862 ай бұрын

  On your amp speaker inputs you got 5 wires the center one is color black did you connect that one or left it alone

• 
  @JCTFIXIT2 ай бұрын

  Ground

• 
  @fatdannyboy2 ай бұрын

  Stupid question but i have to ask since I searched and searched and got nothing. The wires you used in the speaker input to tap into the factory sub, are they normal run of the mill speaker wires or is it a special adapter of some kind?

• 
  @JCTFIXIT2 ай бұрын

  Normal speaker wirewith speaker tab connectors cramped on.

• 
  @jacobwilliams82032 ай бұрын

  What if your amp doesn’t have the speaker input and only has rcas?

• 
  @JCTFIXIT2 ай бұрын

  Then use a line out converter like this: amzn.to/3JaYwPr

• 
  @stevenapperson10163 ай бұрын

  You're amazing. Thank you for the mod. If you ever figure out if I can add power mirrors to my '22 hybrid maverick XL, I'll be over the moon!

• 
  @JCTFIXIT3 ай бұрын

  When you say power, do you mean power fold or just power adjusting?

• 
  @stevenapperson10163 ай бұрын

  @@JCTFIXIT I'm just wanting to add movement up and down, left and right, but I don't need the luxury of folding mirrors. I just don't want manual mirrors if I don't have to live in the stone age 😂

• 
  @JCTFIXIT3 ай бұрын

  I see. Unfortunately I don't have an access to an XL you won't see this video come from me but thanks for watching my man.

• 
  @stevenapperson10163 ай бұрын

  @@JCTFIXIT No problem, I will continue scouring the Earth in my quest! Unless trade in comes first 😂

• 
  @BeyondBlessed693 ай бұрын

  Thanks brother

• 
  @JCTFIXIT3 ай бұрын

  Hopefully you tool advantage of the sweet costco deal!

• 
  @user-hq4nd4ls9k3 ай бұрын

  Any way to do it without that wire

• 
  @JCTFIXIT3 ай бұрын

  Without what wire?

• 
  @LostinTimeYT3 ай бұрын

  Super helpful. Thank you.

• 
  @malabarspyder3 ай бұрын

  I despise interior trim pieces they never seem to look and fit the same .. I wish all MFG just put a removable grille over each speaker but that would be too easy! Love the 4x6 upgrade sorta shocking they fit!

• 
  @JCTFIXIT3 ай бұрын

  Agreed! Haha

• 
  @scottburton42363 ай бұрын

  This seems loud for an inverter generator. What running watt generator is this?

• 
  @JCTFIXIT3 ай бұрын

  Many inverter generators have enclosures around them and thus are much quieter. This model is not enclosed like many inverters are.

• 
  @scottburton42363 ай бұрын

  @@JCTFIXITGotcha. I understand now. Great video, BTW.

• 
  @JCTFIXIT3 ай бұрын

  Thanks! Thanks for reaching out.

• 
  @josephcabiles22953 ай бұрын

  I plan on going with this setup. Couple questions. Does adjusting the bass level from the head unit work on the sub? Will it change the levels for the speakers and the sub simultaneously?

• 
  @JCTFIXIT3 ай бұрын

  Adjusting the amplitude will impact both yes. This is where sub amp tuning comes into play.