Checking and adjusting the throttle body sync on a Yamaha Super Tenere
Жүктеу.....
Пікірлер: 26
@jamesleitholf91194 жыл бұрын
Thank you for taking the time to make this video, Fred. Well done!
@BartSmaalders7 жыл бұрын
That's much much clearer than the manual. Thank you!
@Freddiez43
7 жыл бұрын
Hi Bart. I'm glad that you found it helpful.
@highwayman12183 жыл бұрын
Great video. Ill be doing this soon with a valve adj. Thanks for making it, very informative. 👍
@olliechristopher4674 жыл бұрын
Thank you Fred!! I was going nuts trying to do mine this morning. For the life of me I could not get my screwdriver on the adjuster. DUHH!! Too hard with the tank bolted down. I just did my first spark plug change and buttoned everything back up. I see you lifted your tank to do the sync!! Very good!!
@VPB19708 жыл бұрын
Thank you for sharing you knowledge. Very informative.
@bandit4464846 жыл бұрын
My friend made one out of air tube and a yardstick and transmission fluid to synchronize or Super Teneres. It transforms the throttle control so much better. It’s as smooth as silk now. No on offf with the throttle. What a transformation.
@Freddiez43
6 жыл бұрын
Yes, that will work. The Harmonizer just makes the process easier and is more accurate.
@Denvertubester2 жыл бұрын
Nice tips here, thanks for the video
@peterkaiser57722 жыл бұрын
Hello Fred, great Video! I've only one question, you connect the throttle Sensor at one Side of the T-piece and where ist the second point to connect?
@jollyrgr28547 жыл бұрын
Great job. Thanks.
@Freddiez43
7 жыл бұрын
I'm glad that you found it helpful. Thanks for the feedback.
@manflinflaification7 жыл бұрын
Thank you. Great video. Very clear and simple.
@TheWrate7 жыл бұрын
Thanks for your video. What are the velco pads side panels used for?
@Freddiez43
7 жыл бұрын
I have a velcro pad on the left panel only. I velcro the controller for my heated jacket liner there.
@anomie67884 жыл бұрын
Did it make a difference when you backed out the screw 3/4 of a turn, did it change your idol or anything. ??
@Freddiez43
4 жыл бұрын
It did not change the idle. Just seemed to have a slightly quicker throttle response off of idle.
@blindsquirrel48826 жыл бұрын
Hi Fred, Is it important to have the two tubes the same length, or did you just add the length of tube for the T fitting?
@smainbaba37733 жыл бұрын
Thank you for your video however I have a slow motion problem and can fix it with a synchronization
@Freddiez437 жыл бұрын
Of course that is a 12 mm wrench to loosen th tank pivot bolt. Sorry 'bout that. :-)
@yasinkose7 жыл бұрын
Hello boss. I think at first you unplug the Air pressure sensor hose. you should note it on the video that was wrong. I am right ha?
@Freddiez43
7 жыл бұрын
Greetings. Did I not mention removing that hose at 4:31?
@decaptt
7 жыл бұрын
is it a must to have the T tube to connect the vacuum and sensor? cause my kit comes with two long tubes for the vacuum only... so i have to go out and buy a t tubing?
@Freddiez43
7 жыл бұрын
Yes, it is a must so that the sensor is operational as normal while you are running the engine.
@decaptt
7 жыл бұрын
Fred Ziglar thx man, anyway the tubings are what size. gonna do it tmr
@gdoggydog Жыл бұрын
You should rather use equipment that is currently available to purchase.
Пікірлер: 26
Thank you for taking the time to make this video, Fred. Well done!
That's much much clearer than the manual. Thank you!
@Freddiez43
7 жыл бұрын
Hi Bart. I'm glad that you found it helpful.
Great video. Ill be doing this soon with a valve adj. Thanks for making it, very informative. 👍
Thank you Fred!! I was going nuts trying to do mine this morning. For the life of me I could not get my screwdriver on the adjuster. DUHH!! Too hard with the tank bolted down. I just did my first spark plug change and buttoned everything back up. I see you lifted your tank to do the sync!! Very good!!
Thank you for sharing you knowledge. Very informative.
My friend made one out of air tube and a yardstick and transmission fluid to synchronize or Super Teneres. It transforms the throttle control so much better. It’s as smooth as silk now. No on offf with the throttle. What a transformation.
@Freddiez43
6 жыл бұрын
Yes, that will work. The Harmonizer just makes the process easier and is more accurate.
Nice tips here, thanks for the video
Hello Fred, great Video! I've only one question, you connect the throttle Sensor at one Side of the T-piece and where ist the second point to connect?
Great job. Thanks.
@Freddiez43
7 жыл бұрын
I'm glad that you found it helpful. Thanks for the feedback.
Thank you. Great video. Very clear and simple.
Thanks for your video. What are the velco pads side panels used for?
@Freddiez43
7 жыл бұрын
I have a velcro pad on the left panel only. I velcro the controller for my heated jacket liner there.
Did it make a difference when you backed out the screw 3/4 of a turn, did it change your idol or anything. ??
@Freddiez43
4 жыл бұрын
It did not change the idle. Just seemed to have a slightly quicker throttle response off of idle.
Hi Fred, Is it important to have the two tubes the same length, or did you just add the length of tube for the T fitting?
Thank you for your video however I have a slow motion problem and can fix it with a synchronization
Of course that is a 12 mm wrench to loosen th tank pivot bolt. Sorry 'bout that. :-)
Hello boss. I think at first you unplug the Air pressure sensor hose. you should note it on the video that was wrong. I am right ha?
@Freddiez43
7 жыл бұрын
Greetings. Did I not mention removing that hose at 4:31?
@decaptt
7 жыл бұрын
is it a must to have the T tube to connect the vacuum and sensor? cause my kit comes with two long tubes for the vacuum only... so i have to go out and buy a t tubing?
@Freddiez43
7 жыл бұрын
Yes, it is a must so that the sensor is operational as normal while you are running the engine.
@decaptt
7 жыл бұрын
Fred Ziglar thx man, anyway the tubings are what size. gonna do it tmr
You should rather use equipment that is currently available to purchase.