Tenere 700 Throttle Body Sync
I found there wasn't really a good video covering the Tenere 700 throttle body synchronization procedure. I tried to keep this simple yet informative without spinning off into 17 different directions at once.
Before taking this job on definitely find a service manual online which I have no idea where to find...
motorcycle7usa...
Borrow a Manometer or get a few "trustworthy" vacuum gauges.
Let me know if there's anything in the future on the bike you would like to see. I'm due for fork seals about 7k ago and they're in the mail right now alongside new tires.
Oh yeah, check out www.theouterknobbies.com it's another project of mine as I gain momentum to try to make something of my life before the inevitable marching of time catches up to me.
Ride safe I guess?
Пікірлер: 16
Good, straight forward how to get it done, Cheers!
Great video. I need to check mine.
@cvbadv
2 жыл бұрын
It really does help. It's supposed to be checked as early as the 600km service!
@majormassenspektrometer
7 ай бұрын
Ivhave my tracer which ist identical to tenere for 6 years and never touched the throttle Body. As Long as your engine runs fine you dont need to do this. Before you sync you check and or replace valve clearance, Air Filter and Spark plugs anyway. You just dont only check syncing without all the other important parts for a well running engine.
@majormassenspektrometer
7 ай бұрын
Syncing is the Last step you do after all other important Parameters.
What is that beautiful song?
Amazing video, not the easiest access to the throttle body.
@cvbadv
2 жыл бұрын
Thank you. I tried my best to show everything. Once you have done it a few times it's pretty easy. Get yourself a 90⁰ screwdriver and you can do it without pulling the tank!
What is the maximum and minimum acceptable vacuum pressure? My two are at 12 mm, is this normal? Do I have to raise both to 10 mm? The idle is a little unstable
@cvbadv
Жыл бұрын
That's actually a great question! The amount of vacuum the engine produces depends on your idle speed in this case. Is your idle within specification? If it is the amount of vacuum produced isn't important. What is important is that the vacuum created on each is the same. There's a variance specification in the service manual. (See how I'm making sure you read the manual?) The reason being is the MAP sensor only reads cylinder #1. So cylinder #2 is based off the reading from #1. If they don't match it will be rich or lean and cause poor riding characteristics, which this aims to improve. I hope that explains it.
@Gecata80
Жыл бұрын
According to manual, intake vacuum should be 39.3-41.6 kPa (295-312 mmHg, 11.6-12.3 inHg)
just in 20.000 make this service??? or you first make the valves???
@cvbadv
2 жыл бұрын
This service is due every 7000km if I recall. Valves are due at 42000km.
@panagoskakatosis5314
2 жыл бұрын
@@cvbadv need sybchronize the calbulaor??? every 7000???? in service manual is ??? or you make ???? i have the 750 xtz and in manual is wehn make the valves service then need synchronize..
@cvbadv
2 жыл бұрын
@@panagoskakatosis5314 its a very different bike than the 750 and requires very different service. This bike also has throttle bodies with fuel injectors, not carburetors.
@panagoskakatosis5314
2 жыл бұрын
i will keep the 750 looks more easy for service i make allready the valves and calbutaror only wth calbulator settings spend many time to lern and tests..