This video is SO much more helpful than the one Litter Robot sent me because you show close-ups of all the areas you're working on. Thank you!

@Catevolution1

2 жыл бұрын

Nathan does a wonderful job ! Feel free to subscribe and share 😻

I couldn't have done it without his instructions. Thank you so much.

@Catevolution1

27 күн бұрын

A purrleasure to assist!

Fantastic instructions! This is clear and easy to follow. I replaced my DFI sensors and pinch detectors following this video step by step…the result, a fully operational Litter Robot Thanks Nathan and Cat Evolution!

@salescatevolution9977

2 жыл бұрын

Thank you so much for the feedback Malcolm. Nathan does a wonderful job for us with such easy to follow instructions. Great to have you hands on and now back to no scooping, with the Robot designed for DIY!

This video is a lifesaver. We tried everything to get the DFI sensor working, and this finally did the trick!

@Catevolution1

5 ай бұрын

great to hear it's helpful!

@hateterrorists

Ай бұрын

real pity that it even came to that. I've found this litter robot to be the cheapest, most poorly engineered thing I've ever wasted $800 AUD on. Mother of god what a piece of garbage. It was less fuss to just scoop litter then by this thing that faults out every day with some new nonsense.

This video was so helpful. The instructions that came with the sensors were blurry and unclear. Replaced sensors while watching the video and my litter robot is good as new. Thank you!

@salescatevolution9977

Жыл бұрын

Great to hear! Well done as replacing the DFI is the longer of repairs as you access both base and motorwell. You can now be confident of self installing if you need any parts on the Litter-Robot for great longevity!

@helter-skelter2650

Жыл бұрын

What were the symptoms of your robot? Mine is flashing ready but will not cycle.

Thank you!! The kit I received from litter robot did not come with any instructions. Your step by step instructions made it clear and easy to follow.

@Catevolution1

Жыл бұрын

A purrleasure! FYI installing the DFI is the longer of Robot repairs as you access both base and motorwell. You can now be confident to self install if needed for good longevity!

Thank you! You made replacing my DFI sensors for the 1st time not so difficult. My 2 Sphynx cats told me to thank you as well. I found out this a very common issue with these sensors going bad.

@Catevolution1

6 ай бұрын

Great to hear you have self installed, with the Litter-Robot 3 designed to DIY providing good longevity. The DFI Has been redesigned so the green boards are fully encased to provide durability with varied quality litters, as Whisker.com are excellent in continuing to make improvements if reasonable, even with a new version released. Its a big uptick for the LR3 ;o)

Thank you 🙏🏽 so much for this tutorial ! it was step by step and really easy to follow

@Catevolution1

7 ай бұрын

Great to hear! Nathan does a wonderful job, and its a purrleasure to help keep your Litter-Robot 3 in good working order ;o)

Blaring music > quiet narration > repeat. Besides that, very helpful video.

@Catevolution1

Жыл бұрын

Noted, thank you.

Well made video. Very easy to follow. Thank you.

@salescatevolution9977

2 жыл бұрын

Thank you for the comment. Nathan does a great job!

You’re a legend

@Catevolution1

Жыл бұрын

Good to know its helpful!

Soooo helpful! Thanks!

@Catevolution1

Жыл бұрын

A purrleasure to assist!

you are amazing!

@Catevolution1

Ай бұрын

A purrleasure to assist. Nathan did a great job shooting for Cat Evolution ❤

Better than the whiskers video ive just done this but it wont power on now . Great video though

@Catevolution1

10 ай бұрын

Thank you, purrleased to hear the video is helpful. For no power, check you have the plugs plugged in still in the motorwell, sometimes they can come loose when refitting the cover. You can also test if you open the motorwell, if you add the bonnet to complete the circuit. It can be helpful to unplug each plug to see if you can isolate the sensor that maybe the issue. Also check your power supply is correct. If needed you can send photos to support@catevolution.com.au and I can take a look. DFI, pinch, motorwell, underside are all good photos for review if needed.

Very clear instructions and video amazingly done. I loved the guest appearance of your kitty through the video :) - quick question, at minute 16.14 you said you can check if the DFI sensors are working by placing your phone on video mode. Do you put your phone where the tray would be? meaning the tray would not be inserted in the unit? Thank you

@salescatevolution9977

Жыл бұрын

Hi Marisa, yes, you put your mobile phone into the cavity in the base after removing the waste drawer. Point camera at the left hand side DFI green board, and with the Robot on and your phone in camera mode, you should be able to see the infa read beams flashing as 4 blinking reddish lights, along the left side board. They are not visible to the naked eye. Thank you for your video comment, Nathan does a great job and his cats are devine!

Awesome video.

@Catevolution1

5 ай бұрын

Thank you, glad it's helpful!

Amazing vid. I had replaced the DFI couple of years ago but now it failed. I had this time bought the DFI sensors version 2 . An improved version, the cards are shorter and insulated. Do you happen to have the v2 installation video? Tks.

@salescatevolution9977

Жыл бұрын

sadly not released overseas yet, but coming.... my understanding is the installation is the same. Check your pinch detectors too!

@sbsani

Жыл бұрын

@@salescatevolution9977 l 'm from Singapore, just got it from Robot shop Japan. Its so much better from v1. Installation is a breeze and works perfectly. v2 is abt 1/3 the original size. The sensor card housing/bracket is slightly different. The pinch detector was totally rusted and got it replaced. I'm trying to fabricate a brass detector instead.

@salescatevolution9977

Жыл бұрын

@@sbsani good to hear. Maybe we will have it available sooner than expected!

@salescatevolution9977

Жыл бұрын

@@sbsani great to hear as we are looking to get these in for Australia and NZ. for the pinch detectors, I think they maybe brass under the silver metal coating. Brass oxidises which may slow the power tranfer. The best thing is to use good quality clumping clay litter that locks in the uric acid in cat pee, and keeps the odour and base cleaner.

@sbsani

Жыл бұрын

@@salescatevolution9977 I agree. Thanks for the advice. Then I may try and use a stainless steel strips instead.

Thank you for this amazing video! You showed so much detail, and that made all the difference in the world. Trying to figure out how to install the DFI would have been a nightmare without this video. Charlotte, Dutchess, Bittle and Tigger thank you a million times over for saving the day!😊

@Catevolution1

2 ай бұрын

A purrleasure! Nathan did a wonderful job shooting the video and it helps to see more detail when installing. Its not that its too hard, but it needs to be done step by step and takes a little while. Well done on your installation and you can now be confident on self installing if needed for good longevity, as the DFI is the longer of repairs due to accessing both motorwell and base. Well done YOU!!

My LR3 starts to have flashing blue lights, when pressed the reset it changed to flashing yellow light rapidly. Do you think my DFI sensor is also bad? I checked the left side of the IR led with phone camera they are not flashing. Thanks!

@Catevolution1

Жыл бұрын

Yes, DFI and pinch detectors need attention, most likely replacing.

Your instructions were easy to follow, but alas, when I attempted to turn on the unit there was no power. What might I have disconnected? Thank your assistance.

@Catevolution1

Жыл бұрын

Check your power supply for damage. Also turn on (no power) and feel the control buttons. If they are warm, there is power coming to the board ok. Check you have the DFI still plugged in the motorwell, as sometimes it comes out when you put the cover back on. Do ensure you add the tape to keep the wires clear of the black gear wheel.

@veronicagandaradvm1635

Жыл бұрын

@@Catevolution1 My bad. I looked at the circuit board and saw a plug was detached. I reconnected the plug and the unit was powered, all is fantastic. Your video was spectacular! I was extremely reluctant to replace the DFI sensor but you made a dauting task easy. Thank you so very much.

@Catevolution1

Жыл бұрын

AWESOME!! Well done. And fyi, installing DFI is the longer of repairs, due to accessing motorwell and base, so you can be confident to do self installation for great longevity!

The LR Cat Sensor DIY kit I received just has a wheel, a spring, a rectangular metal cover and a long screw. It is not what you are installing. What did I really get and how do I install this? My problem is the LR doesn't register the weight of lighter cats l. I've tried tightening the screw in the top is the drawer space but it won't go any tighter so they sent me this. Should they have sent me what you installed? Help!! Thanks!

@Catevolution1

Жыл бұрын

You have a cat sensor kit.

@Catevolution1

Жыл бұрын

kzread.info/dash/bejne/qYCrydxsmLrNfco.html

I could really really use some advice please . I'm honestly starting to get so cross and frustrated . I finally received my replacement dfi and pinch sensors..sat yesterday and replace both the pinch brackets and the dfi . The pinch sensors are touching as they should be and the wires connecting to them are secure . As is the one to the control panel . My litter robot is still not working .. Still a constant flashing blue light as if the waste drawer is full . I don't proclaim to be a expert but I've stripped down xbox and switch controllers and rebuilt with no issues so I have a bit of experiencing with electronics. I can't work this out and I'm about to throw this thing into a dump . Please help

@Catevolution1

Жыл бұрын

Do make sure you have the DFI plugged into the mainboard the right way. The dark wires should be uppermost with the brighter wires close to the wide bottom of the mainboard. There is a channel and groove that line up on plug and socket if you look closely to help. If not sure, unplug and turn upside down and replug to test.

@christinebrookes4586

Жыл бұрын

@@Catevolution1 not sure if my comment posted as j can't see jt . Just wanted to thank you for taking the time to reply. I had actually managed to get it workimg I squeezed the pinch sensors together with pliers . Disconnected a couple bunches of wires from a black plastic piece by accent and couldn't get the tabs back I'm but I'm not sure they actually do anything lol, for now it's working

@Catevolution1

Жыл бұрын

@@christinebrookes4586 good to hear you are back in working order. Not sure what you have disconnected. I would suggest you get in touch with the company you purchased from by email and provide photos for further assistance as there are some parts that are safety features and need to be in place. Thanks for the update !

I did install the parts and the blue light is still flashing. What else could I do? Also my robot is not connecting online.

@salescatevolution9977

2 жыл бұрын

You are welcome to send photos to customer support to see if the installation is correct. Is your Robot a Connect? Provide serial number for review.

@samuellarsen3355

20 күн бұрын

did you ever figure this out? Same issue. Replaced DFI, everything looks good, still slow blinking blue light when i power on

after following this video step by step I replaced the dfi kit put it all back together. plugged it in and yellow cycle light stays lit. it will not reset, cycle or power on/off nothing happens just stays on yellow light. on the app it says robot is off. please help

@Catevolution1

Жыл бұрын

do you have blue and yellow solid or just yellow? if just yellow check you have the dfi plugged into main board right way up. if 2 solid lights you are in sleep mode. Press and hold CYCLE 3-5 seconds until 1 light goes out.

@peterc6197

Жыл бұрын

@@Catevolution1 just solid yellow, dfi is plugged in correctly as it only fits one way. It is a newer updated model dfi as the circuit board is different. Much more short not as long. Controls do not work, app does not work saying robot is off

@salescatevolution9977

Жыл бұрын

@@peterc6197 Do check the DFI plug, the ones I see have 4 pins, so square and are sometimes put in upside down. Otherwise, maybe motor or main circuit board issue. I suggest you reach out to the company you purchased from as its little difficult to do this on youtube without photos to review. Where are you located? (country). We are Australia and NZ only.

Flashing blue light solution, parts installation

First, the instructions on any video related to this are off because the wires and even the plastics pieces shown are not what’s in the newer versions of the LR3. So that took time figuring out. They need to update the videos. Second, I went through all of this to have the same issue; nothing has changed. At this point, I am highly dissatisfied with this product I’ve had less than 8 months.

@Catevolution1

4 ай бұрын

Thank you for your feedback. I suggest you contact where you purchased the Litter-Robot as this video was created in Australia in 2021, with the process for the DFI version 1 similar but not the same for the revised (new version ) of DFI v2. Whisker.com is the manufacturer and can assist you further if you are not able to contact the company you purchased from (it appears you are USA based). If nothing has changed following installing the new DFI successfully, and you still have a flashing blue light, check you installed the DFI mainboard plug the correct way up. There is channel and groove to assist that need to be checked when installing. WE trust this assists.

@ms.ashley

4 ай бұрын

@@Catevolution1 yes I called them and they are sending a new base, free under warranty

@Catevolution1

4 ай бұрын

Good to hear. Whisker is a great company who fully support their products@@ms.ashley

I think it will be much easier and less work if you remove the bottom part first, then work on the top part, removing the wires, dfi etc.

@Catevolution1

Жыл бұрын

I actually do that, but you do need to squeeze and pop out the cable clip where the wires go up into the motorwell

@TeleeFONE

Жыл бұрын

@@Catevolution1 I take off the bottom first just now, still less work. Great video though and guide for me install new dfi, now my LR is working again. FYI now it is v2 dfi it is different and the sensor is 70% smaller and completely covered up with silicone or something, much better.

@Catevolution1

Жыл бұрын

@TeleeFONE yes, new version DFI is big uptick for LR3 😻

@TeleeFONE

Жыл бұрын

@@Catevolution1 yup saw the new version and impressed, hope this will last a long time coz my LR been giving me so many issues lately 🥲, breakdown every other month and something need replacement. 5 year owner of LR3.

@Catevolution1

Жыл бұрын

@@TeleeFONE use good clumping litter (solid clumps) if dusty, use brush end on vacuum to suck clean base area when deep cleaning. New DFI should be pretty much proof against poor quality litter.

This better work or iam throwing it in the bin

@Catevolution1

Жыл бұрын

Oh, dont do that! just ask support for help. Its a great appliance and designed for self installation, with support available. If you do decide its not for you, put a message out and Im sure it will be rehomed !