Harley Davidson bagger Road King road glide electric glide ultra glide classic Throttle by wire issues.
Жүктеу.....
Пікірлер: 113
@user-tr7fy4eg2f19 күн бұрын
Exactly what I needed! Thanks for taking the time to make the video!
@Cmfr19883 жыл бұрын
Didn't even think to look there... I didn't start having problems till I hooked up my lights and my seat been pushing down on it all making it open... your a hero lol
@watsonmotorsports8753
3 жыл бұрын
Glad I could help please subscribe to my channel!
@dalewvr11 ай бұрын
Good video! And info! Thank you!! And for those of you reading this , when you plug everything back up a little dielectric-grease won’t hurt either
@Gque_2 ай бұрын
Having the same issue. Bike just went into limp mode on the highway. Scared the shit put me. 😂. Pulled over and it started back up. Finally got it home after three more times. Found this video and going home today and try it.
@losgonzalez70343 жыл бұрын
Thank you, I had the same issue. I stalled on the freeway and couldn't clear the ECM code and rode the bike home with a rough idle. I watch your video, re-seated the emc connectors and was able to clear the codes. readjusting my connections under the seat now.
@harryfurman77182 ай бұрын
Just wanna say thank you you were thorough and you answer the question that I need to try to find out because I was having that limp mode on the 2009 and a couple other things that you brought to. My attention was really helpful. Thank you very much for making the video to help others.
@pmartinagejr2 жыл бұрын
I just want to say thank you, thank you, thank you! I was having trouble not being able to reset my TPS codes and one of your trouble spots was the problem! The ECM connector was not making a good connection. Evidently when I replaced my battery I must not have snapped the locking clamp fully and it loosened up. Great video for troubleshooting this issue
@watsonmotorsports8753
2 жыл бұрын
Glad you got it figured out!
@bobbyagee37963 жыл бұрын
So three points of possible issue. Voltage to the ECM caused by an aftermarket seat. Appreciate it
@gkase39792 жыл бұрын
That's a clean ride man. I disconnected and cleaned the ecu and cable by the air intake and the bus we went away and started right up
@dwaynehunter95104 жыл бұрын
Great help. My seat did the same thing. Thank you!
@billcovert271611 ай бұрын
Great video. Great info. It helped me with my 08 Electra Glide. Bike is pretty slick too.
@outlaw68494 жыл бұрын
Great Tip, Great looking Bike!
@MyllekeBas2 жыл бұрын
Thanks bro! You saved my tripp to Sweden ;-)
@davidfellows62502 жыл бұрын
thank you good sir. I've got a 2014 doing this and I have an amp under my seat so tomorrow...... thanks again.
@kentmclaughlin98852 жыл бұрын
On and off worked, awsome ! Thanks
@kenchan56243 жыл бұрын
Thank you dude great information,l got the same bike ,ride safe bro.
@buddyheph2 жыл бұрын
You just saved me…Appreciate you brotha!
@watsonmotorsports8753
2 жыл бұрын
Good deal!
@Tom-jw1pe Жыл бұрын
I’ma check this out on my bike… appreciate the video
@benjaminhurst82072 жыл бұрын
I was having an issue with the throttle by wire and it ended up being a issue with the throttle body/ entire fuel injection system. Was able to replace that whole unit behind the air filter there for $250 about oem from Harley and it fixed my problem.
@bubbyhardy61352 жыл бұрын
Having the issue on my 08 sg. Keeps going into limp mode all of a sudden. I found this video and gonna dig into the things u mentioned. Thanks for sharing brother.
@drtomasdds
2 жыл бұрын
Just had same issue on my 08 sg last week. I never thought to check KZread. It’s at dealer now $$$.
@bubbyhardy6135
Жыл бұрын
@@drtomasdds that was exactly what was wrong with mine. I took it apart and cleaned all the pins and havent had a issue since. Its a shame u didnt try yourself cause i know those dealer mechanics can really rack you. Good luck bro, hope u get her fixed.
@SonOfaBeatnik2 жыл бұрын
I’m gonna use this to hopefully solve my issue. Thank you for your research and helping with explaining all the related electrical connections for the throttle. Crossing fingers 🫰🏼
@rastroyfyah56303 жыл бұрын
Lots of info bro great video
@got2b9183 жыл бұрын
Good stuff! One thing I didn't check, so I might have the same issue as you. Thx
@davidsims8636 Жыл бұрын
Thank you sir. Exact problem I was having
@Jbainbridge55 ай бұрын
Awesome video. I'm having some codes being thrown close to Daytona Bikeweek. Now I'm in panic mode. Another key factor is making sure your battery is secured...
@thecommodity6957 Жыл бұрын
man you have a bad ass! bike, I have an 07' with throttle not responding after I ran it for a while doing some parking lot tight u-turn practice so dont think this will resolve my issue but it gets me looking in the right places.
@oscarsorto74524 ай бұрын
Thank bro ,this video is very helpful
@flintstone19832 жыл бұрын
Great video, thanks !
@stevendekold4579 Жыл бұрын
Great video. Thank you!
@gregrose69152 жыл бұрын
Had a p1510 & p2138 code that wouldn't clear on my 08 Ultra. Pulled the throttle body plug apart behind the air filter, put some die-electric grease on it, put it back together, codes and engine light cleared a went off.
@GenOakFab
2 жыл бұрын
Had the same issue with my 09 street glide. 👍🏽
@lancemedlin47123 жыл бұрын
Appreciate the video!!!
@AceXhole8118 Жыл бұрын
Thx !
@tomeyster33602 жыл бұрын
Great video!
@charlesmccormick44432 жыл бұрын
The connector in the bars also corrodes causing problems , the S E twist grip sensor does not have the connector and has longer wire , or you could cut the connector out and solder longer wire on insulated well . Some times you can unplug and plug in the throttle body connector 2-3 times and it gets better contact , if thats the problem . The ecm plugin , if you noticed has a bunch of pins , easy to bend , fold over and break , or bend over and short circuit . I used the S E twist grip sensor when I put LA chopper 10" twin peaks on 08 ultra the wire reached all the way to the plugin with just a little slack left . I also bought a spare throttle body off a 2010 wreck , they had a video of it running , out side of the injectors and map sensor , the electronic part of the throttle body is not repairable , its a throw away .
@ApolloGrewe10 ай бұрын
Nice Video Bro!!!
@robertnunn4973 жыл бұрын
just installed new 12 inch yaffes on my UC. Everything works except no throttle. Codes P1510 and P2138. Was wired by HCC, who do it for a living so, I really don't think it's an internal wire issue. I will certainly check those 2 recommendations when I get home today. Thanks
@zoltan-nandorbone4422 Жыл бұрын
Very nice bike!
@agbayani8083 жыл бұрын
great info!
@joshrivers58702 жыл бұрын
Beautiful bike
@richardrussell5007 ай бұрын
Great video... :-)
@ut1004bp6 ай бұрын
Yes, helpful
@usmcmpd7 ай бұрын
Bro great video! Very knowledgeable
@user-ew6dy6ex4c11 ай бұрын
Holmes can't thank you enough.....🤙
@cc-pl7tw Жыл бұрын
Thanks for sharing
@jasonusaf63264 жыл бұрын
That’s a beautiful bike man
@watsonmotorsports8753
4 жыл бұрын
Thanks!
@racex372110 ай бұрын
Thank you my low rider s loses power at 3,500 rpm when wide open hopefully it will be something easy to fix never had that problem until after it was tuned
@ronniemartin83918 ай бұрын
Helpful
@MisdemeanorMisdemeanor Жыл бұрын
Nice bike.
@billbermudez59743 жыл бұрын
like the bike
@safeeffective3853 жыл бұрын
Righteous scooter
@JohnVeeOfficial Жыл бұрын
Great thanks! I have to check that out…. Recently I changed a battery and my Harley is stalling…. It gives me an error p1511…
@MrNetnut3 ай бұрын
Damn Nice Bike/;-))) thanks
@chip9832Ай бұрын
💯
@Dawop10 ай бұрын
Great video brother very detailed thanks
@Sunroofs_unltd7133 жыл бұрын
When you had the issues what exactly what’s the problem I have a 09 road king , starts fine,idles fine, pull off mite make it a block seem like throttle response dies, bike never shuts off, just idles
@cnm6424 жыл бұрын
Thanks for the video! I believe what I am experiencing is due to the limp mode issue with eratic idling, losing throtle connection when I hit a bump, etc. Anyways, I have another issue where I turn on my ignition and I do not have power, intermittently. I may see the lights flicker and then no power. It seems that I don't have a complete circuit with the ignition. I do have a new battery and I have checked all fuses and relays. I'm wondering if the issue you are describing you are having with the ECM connection also had you not able to close the circuit when you turn on th ignition. I get it to close the circuit after I bounce on the seat a few times which is why I thought of the ECM connection, maybe not closing the loop. Thanks in advance!
@watsonmotorsports8753
4 жыл бұрын
Its in that large connector under the seat.
@cnm642
4 жыл бұрын
@@watsonmotorsports8753 but is that ECM connection causing no power when you turn on the ignition?
@Richard58732 жыл бұрын
IF I purchased a new ECM can I just plug it in and replace it ? Or does it have to be taken to a dealership??
@bansheebrown51154 жыл бұрын
What are some other common issues you would run into on the early road king? I’m about to purchase a 95 Road King
@watsonmotorsports8753
4 жыл бұрын
I would look for a twin cam which is a 2000 and newer model.
@AJV4L20073 жыл бұрын
How do you clear ecm
@jimwortham8634 Жыл бұрын
Amazing how some people spend thirty thousand and have a limp mode problem
@victorwest8041 Жыл бұрын
are all fuel injected bikes throttle by wire or do some still use a cable?
@leonelrodriguesrodrigues31039 ай бұрын
Dear, the code 2138 road king 2008 appeared. Do you have any tips for a solution?
@jeffeversole291 Жыл бұрын
Thanks for sharing brother. What type of seat?
@watsonmotorsports8753
Жыл бұрын
Factory oem
@michaeljoesmith39773 жыл бұрын
I'm wondering if my Ultra Classic has the same problem. What happens is I'll be riding down the road and suddely the engine goes to idle and the throttle will not increase rpm. So I pull over to the shoulder of the road ,restart my bike and it seems normal. But then it happens again in a few miles. Also I've noticed my engine light coming on for about 10 seconds when I start the bike. Thanks for the video. I'm going to check all the areas you mentioned here.
@waylonshrewsbury652
2 жыл бұрын
Hey Michael Joe Smith, I've got an 08 ultra classic doing the exact same thing you said yours is doing. What did you wind up doing to fix it?
@michaeljoesmith3977
2 жыл бұрын
@@waylonshrewsbury652 I ended up having a new throttle sensor installed. Cost about $300 including labor. Bike is doing fine now, knock wood.
@waylonshrewsbury652
2 жыл бұрын
Awesome. Thanks
@walteralvarado3640
Жыл бұрын
How you doing did you fix your problem on your bike having the same problem already change the connector plug all in the air filter and it's still doing the same thing do you have any ideas what can you do
@michaeljoesmith3977
Жыл бұрын
@@walteralvarado3640 I had a new throttle sensor installed by a mechanic friend. He charged me 300 dollars parts and labor. If you want to do it yourself you can find that part on Amazon, I think.
@Halfboxing3 жыл бұрын
Man I’m still wondering what happened to my bike. I try to open the throttle fast and it bogs out I have to take it easy or else it won’t go but once it catches it’s good just can’t fully open throttle fast
@morganW2012
3 жыл бұрын
2012 fltrx I'm having same issue, throttled it out and it died, I thought I blew the motor but.?. I'm searching if you get info pass along
@alanplambeck6608 Жыл бұрын
I have a 2010 road king classic and I had the same problem that throttle response I have none it will idle but it won’t have no throttle
@carlitosperez30924 жыл бұрын
How does the 2 into 1 shorter exhaust work for you?
@watsonmotorsports8753
4 жыл бұрын
I chose that exhaust for 2 reasons and either reason had to do with performance. I wanted something that looked good and sounds radical! And I think I got it with that pipe. LIKE SHARE SUBSCRIBE!!!
@aarsenalfan2 жыл бұрын
Nice pipes, if you don't mind what are those ? 👌👌
@watsonmotorsports8753
2 жыл бұрын
Covington
@Richard58732 жыл бұрын
How do you know if the ECM reset after turning on/off 4x ?
@watsonmotorsports8753
2 жыл бұрын
Codes are cleared.
@Richard5873
2 жыл бұрын
@@watsonmotorsports8753 Mines not showing any codes , trying to determine if mine is going Stupid
@mrvbaker4 жыл бұрын
What kit did you use for your 26
@watsonmotorsports8753
4 жыл бұрын
American Suspension
@mrvbaker
4 жыл бұрын
Ok thanks
@piqui394 жыл бұрын
what were the symptoms ?
@watsonmotorsports8753
4 жыл бұрын
Misfire and sputtering just not running right!
@chestypuller96142 жыл бұрын
What pipes are them nicccce
@watsonmotorsports8753
2 жыл бұрын
Covington
@DADDY04223 жыл бұрын
Thanks Bro! my bike will start and shut off 2 seconds later...moving the throttle dose not rev the engine at all. code P1512.. any help will be greatly appricated
@watsonmotorsports8753
3 жыл бұрын
Twist grip sensor could be bad. Check everything I showed in the video.
@DADDY0422
3 жыл бұрын
@@watsonmotorsports8753 Thanks Bro💯
@gemin_outlaw3 жыл бұрын
Is it getting reset if the key is not there?
@watsonmotorsports8753
3 жыл бұрын
I believe key fob must be present for ecm to read.
@gemin_outlaw
3 жыл бұрын
I have a 2008 Harley Davidson Fatboy, it's getting high rpm once it's start...it's a esp injection what should I need to check first?
@MrLhill12223 жыл бұрын
Shit that might be my issue
@Robbanks08054 жыл бұрын
Throttle by wire? Considering there are no wires on your throttle and the bike is fuel injected, I think you mean electronic throttle.
@watsonmotorsports8753
4 жыл бұрын
The wire is on the twist grip sensor and electronically sends signal
@larrycrow84313 жыл бұрын
Don't even know what your riding, called your road king, road guide 3 times
@watsonmotorsports8753
3 жыл бұрын
Lol!!! I got more toys than I can keep up with so can I hire you to keep things in perspective?
Пікірлер: 113
Exactly what I needed! Thanks for taking the time to make the video!
Didn't even think to look there... I didn't start having problems till I hooked up my lights and my seat been pushing down on it all making it open... your a hero lol
@watsonmotorsports8753
3 жыл бұрын
Glad I could help please subscribe to my channel!
Good video! And info! Thank you!! And for those of you reading this , when you plug everything back up a little dielectric-grease won’t hurt either
Having the same issue. Bike just went into limp mode on the highway. Scared the shit put me. 😂. Pulled over and it started back up. Finally got it home after three more times. Found this video and going home today and try it.
Thank you, I had the same issue. I stalled on the freeway and couldn't clear the ECM code and rode the bike home with a rough idle. I watch your video, re-seated the emc connectors and was able to clear the codes. readjusting my connections under the seat now.
Just wanna say thank you you were thorough and you answer the question that I need to try to find out because I was having that limp mode on the 2009 and a couple other things that you brought to. My attention was really helpful. Thank you very much for making the video to help others.
I just want to say thank you, thank you, thank you! I was having trouble not being able to reset my TPS codes and one of your trouble spots was the problem! The ECM connector was not making a good connection. Evidently when I replaced my battery I must not have snapped the locking clamp fully and it loosened up. Great video for troubleshooting this issue
@watsonmotorsports8753
2 жыл бұрын
Glad you got it figured out!
So three points of possible issue. Voltage to the ECM caused by an aftermarket seat. Appreciate it
That's a clean ride man. I disconnected and cleaned the ecu and cable by the air intake and the bus we went away and started right up
Great help. My seat did the same thing. Thank you!
Great video. Great info. It helped me with my 08 Electra Glide. Bike is pretty slick too.
Great Tip, Great looking Bike!
Thanks bro! You saved my tripp to Sweden ;-)
thank you good sir. I've got a 2014 doing this and I have an amp under my seat so tomorrow...... thanks again.
On and off worked, awsome ! Thanks
Thank you dude great information,l got the same bike ,ride safe bro.
You just saved me…Appreciate you brotha!
@watsonmotorsports8753
2 жыл бұрын
Good deal!
I’ma check this out on my bike… appreciate the video
I was having an issue with the throttle by wire and it ended up being a issue with the throttle body/ entire fuel injection system. Was able to replace that whole unit behind the air filter there for $250 about oem from Harley and it fixed my problem.
Having the issue on my 08 sg. Keeps going into limp mode all of a sudden. I found this video and gonna dig into the things u mentioned. Thanks for sharing brother.
@drtomasdds
2 жыл бұрын
Just had same issue on my 08 sg last week. I never thought to check KZread. It’s at dealer now $$$.
@bubbyhardy6135
Жыл бұрын
@@drtomasdds that was exactly what was wrong with mine. I took it apart and cleaned all the pins and havent had a issue since. Its a shame u didnt try yourself cause i know those dealer mechanics can really rack you. Good luck bro, hope u get her fixed.
I’m gonna use this to hopefully solve my issue. Thank you for your research and helping with explaining all the related electrical connections for the throttle. Crossing fingers 🫰🏼
Lots of info bro great video
Good stuff! One thing I didn't check, so I might have the same issue as you. Thx
Thank you sir. Exact problem I was having
Awesome video. I'm having some codes being thrown close to Daytona Bikeweek. Now I'm in panic mode. Another key factor is making sure your battery is secured...
man you have a bad ass! bike, I have an 07' with throttle not responding after I ran it for a while doing some parking lot tight u-turn practice so dont think this will resolve my issue but it gets me looking in the right places.
Thank bro ,this video is very helpful
Great video, thanks !
Great video. Thank you!
Had a p1510 & p2138 code that wouldn't clear on my 08 Ultra. Pulled the throttle body plug apart behind the air filter, put some die-electric grease on it, put it back together, codes and engine light cleared a went off.
@GenOakFab
2 жыл бұрын
Had the same issue with my 09 street glide. 👍🏽
Appreciate the video!!!
Thx !
Great video!
The connector in the bars also corrodes causing problems , the S E twist grip sensor does not have the connector and has longer wire , or you could cut the connector out and solder longer wire on insulated well . Some times you can unplug and plug in the throttle body connector 2-3 times and it gets better contact , if thats the problem . The ecm plugin , if you noticed has a bunch of pins , easy to bend , fold over and break , or bend over and short circuit . I used the S E twist grip sensor when I put LA chopper 10" twin peaks on 08 ultra the wire reached all the way to the plugin with just a little slack left . I also bought a spare throttle body off a 2010 wreck , they had a video of it running , out side of the injectors and map sensor , the electronic part of the throttle body is not repairable , its a throw away .
Nice Video Bro!!!
just installed new 12 inch yaffes on my UC. Everything works except no throttle. Codes P1510 and P2138. Was wired by HCC, who do it for a living so, I really don't think it's an internal wire issue. I will certainly check those 2 recommendations when I get home today. Thanks
Very nice bike!
great info!
Beautiful bike
Great video... :-)
Yes, helpful
Bro great video! Very knowledgeable
Holmes can't thank you enough.....🤙
Thanks for sharing
That’s a beautiful bike man
@watsonmotorsports8753
4 жыл бұрын
Thanks!
Thank you my low rider s loses power at 3,500 rpm when wide open hopefully it will be something easy to fix never had that problem until after it was tuned
Helpful
Nice bike.
like the bike
Righteous scooter
Great thanks! I have to check that out…. Recently I changed a battery and my Harley is stalling…. It gives me an error p1511…
Damn Nice Bike/;-))) thanks
💯
Great video brother very detailed thanks
When you had the issues what exactly what’s the problem I have a 09 road king , starts fine,idles fine, pull off mite make it a block seem like throttle response dies, bike never shuts off, just idles
Thanks for the video! I believe what I am experiencing is due to the limp mode issue with eratic idling, losing throtle connection when I hit a bump, etc. Anyways, I have another issue where I turn on my ignition and I do not have power, intermittently. I may see the lights flicker and then no power. It seems that I don't have a complete circuit with the ignition. I do have a new battery and I have checked all fuses and relays. I'm wondering if the issue you are describing you are having with the ECM connection also had you not able to close the circuit when you turn on th ignition. I get it to close the circuit after I bounce on the seat a few times which is why I thought of the ECM connection, maybe not closing the loop. Thanks in advance!
@watsonmotorsports8753
4 жыл бұрын
Its in that large connector under the seat.
@cnm642
4 жыл бұрын
@@watsonmotorsports8753 but is that ECM connection causing no power when you turn on the ignition?
IF I purchased a new ECM can I just plug it in and replace it ? Or does it have to be taken to a dealership??
What are some other common issues you would run into on the early road king? I’m about to purchase a 95 Road King
@watsonmotorsports8753
4 жыл бұрын
I would look for a twin cam which is a 2000 and newer model.
How do you clear ecm
Amazing how some people spend thirty thousand and have a limp mode problem
are all fuel injected bikes throttle by wire or do some still use a cable?
Dear, the code 2138 road king 2008 appeared. Do you have any tips for a solution?
Thanks for sharing brother. What type of seat?
@watsonmotorsports8753
Жыл бұрын
Factory oem
I'm wondering if my Ultra Classic has the same problem. What happens is I'll be riding down the road and suddely the engine goes to idle and the throttle will not increase rpm. So I pull over to the shoulder of the road ,restart my bike and it seems normal. But then it happens again in a few miles. Also I've noticed my engine light coming on for about 10 seconds when I start the bike. Thanks for the video. I'm going to check all the areas you mentioned here.
@waylonshrewsbury652
2 жыл бұрын
Hey Michael Joe Smith, I've got an 08 ultra classic doing the exact same thing you said yours is doing. What did you wind up doing to fix it?
@michaeljoesmith3977
2 жыл бұрын
@@waylonshrewsbury652 I ended up having a new throttle sensor installed. Cost about $300 including labor. Bike is doing fine now, knock wood.
@waylonshrewsbury652
2 жыл бұрын
Awesome. Thanks
@walteralvarado3640
Жыл бұрын
How you doing did you fix your problem on your bike having the same problem already change the connector plug all in the air filter and it's still doing the same thing do you have any ideas what can you do
@michaeljoesmith3977
Жыл бұрын
@@walteralvarado3640 I had a new throttle sensor installed by a mechanic friend. He charged me 300 dollars parts and labor. If you want to do it yourself you can find that part on Amazon, I think.
Man I’m still wondering what happened to my bike. I try to open the throttle fast and it bogs out I have to take it easy or else it won’t go but once it catches it’s good just can’t fully open throttle fast
@morganW2012
3 жыл бұрын
2012 fltrx I'm having same issue, throttled it out and it died, I thought I blew the motor but.?. I'm searching if you get info pass along
I have a 2010 road king classic and I had the same problem that throttle response I have none it will idle but it won’t have no throttle
How does the 2 into 1 shorter exhaust work for you?
@watsonmotorsports8753
4 жыл бұрын
I chose that exhaust for 2 reasons and either reason had to do with performance. I wanted something that looked good and sounds radical! And I think I got it with that pipe. LIKE SHARE SUBSCRIBE!!!
Nice pipes, if you don't mind what are those ? 👌👌
@watsonmotorsports8753
2 жыл бұрын
Covington
How do you know if the ECM reset after turning on/off 4x ?
@watsonmotorsports8753
2 жыл бұрын
Codes are cleared.
@Richard5873
2 жыл бұрын
@@watsonmotorsports8753 Mines not showing any codes , trying to determine if mine is going Stupid
What kit did you use for your 26
@watsonmotorsports8753
4 жыл бұрын
American Suspension
@mrvbaker
4 жыл бұрын
Ok thanks
what were the symptoms ?
@watsonmotorsports8753
4 жыл бұрын
Misfire and sputtering just not running right!
What pipes are them nicccce
@watsonmotorsports8753
2 жыл бұрын
Covington
Thanks Bro! my bike will start and shut off 2 seconds later...moving the throttle dose not rev the engine at all. code P1512.. any help will be greatly appricated
@watsonmotorsports8753
3 жыл бұрын
Twist grip sensor could be bad. Check everything I showed in the video.
@DADDY0422
3 жыл бұрын
@@watsonmotorsports8753 Thanks Bro💯
Is it getting reset if the key is not there?
@watsonmotorsports8753
3 жыл бұрын
I believe key fob must be present for ecm to read.
@gemin_outlaw
3 жыл бұрын
I have a 2008 Harley Davidson Fatboy, it's getting high rpm once it's start...it's a esp injection what should I need to check first?
Shit that might be my issue
Throttle by wire? Considering there are no wires on your throttle and the bike is fuel injected, I think you mean electronic throttle.
@watsonmotorsports8753
4 жыл бұрын
The wire is on the twist grip sensor and electronically sends signal
Don't even know what your riding, called your road king, road guide 3 times
@watsonmotorsports8753
3 жыл бұрын
Lol!!! I got more toys than I can keep up with so can I hire you to keep things in perspective?
💯