I'd put metal chafe bands over the hose where it is close to other components. Once you fill the line with fluid, and run the engine, the hose will vibrate some, and could chafe through if you don't.

@ThePaintPaperHustle

2 ай бұрын

Thanks for that tip. This video is alittle older and we never had an issue thankfully

Hell yeah. Closer and closer

@ThePaintPaperHustle

2 жыл бұрын

👊🏻

Been struggling with the -20. I’m going to try your boiling water suggestion. Thanks for the vid. 👍💪🤘

@ThePaintPaperHustle

3 ай бұрын

You’re welcome

tip - i found it wayyy easier if you put the hose in the vise and get a socket big enough for the hose end ... slips on super easy than cranking while you push in

@ThePaintPaperHustle

8 ай бұрын

Great tip thanks

Looks good and it's not going to leak

@ThePaintPaperHustle

2 жыл бұрын

Thanks Mr Scott

You can hear the female side n it will expand just enough so it will tighten all the way up. A lot of ppl leave it like that n it leaks or doesn't look as good. There was a video on here that I seen that only one guy did that like I did. But ya just use a reg propane torch n heat it n it will tighten all the way up. It might be just as hard since that is China I'm not for sure. But just keep heating it until you can turn it n it will eventually button up. Hope that helps, I'm in the middle of a build also n I have to even ask or look for some of the new stuff

@ThePaintPaperHustle

4 ай бұрын

Yea I’ve actually done that to some of the hoses. Idk why I didn’t do that to this one. Maybe this was before I learned that trick. It never did leak though.

Looks great, I would buy the hose the same place! keep them coming!

@ThePaintPaperHustle

2 жыл бұрын

Thanks. I was going to share listing but it’s been removed.

@NickHerAmerican

7 ай бұрын

Any new links?

@ThePaintPaperHustle

7 ай бұрын

@TheVloneGod no sorry they change all the time. You’ll just have to search eBay for -20an

Man im late!!!!🤘🤘🤘

@ThePaintPaperHustle

2 жыл бұрын

Lol never

i used to but alot of stuff off amazon and ive ran a bunch of nylon braided AN hose and hose ends. and i had the PTFE braided hose and hose ends on my truck and customer cars and ive never had one fail before. i buy local now just to support the people that support me . but when it come to alcohol i wouldnt use it but the amazon PTFE stuff ive never had a issue for 3 years on ignite E90. but for radiator hose its not gonna be corrosive nor will it see barely any pressure so i wouldnt worry about it

@ThePaintPaperHustle

2 жыл бұрын

Good to know. Thanks for that info

@NickHerAmerican

7 ай бұрын

Links?

That shit aint going to leak lol, i mounted the suction side of the pump directly to the radiator with a short piece of hose and T bolt clamps. Also have a bracket welded to the radiator to help hold the pump some although the hose from pump to engine holds it fine, just a little more security on drag n drive events so the radiator outlet doesnt crack.

@ThePaintPaperHustle

2 жыл бұрын

You’re smart. Always better to be safe than sorry right. And yea I don’t think it’ll leak either.

😎

@ThePaintPaperHustle

2 жыл бұрын

👊🏻

I purchased some of that Chinese A/N line and fittings and cursed that junk until the day I tossed that sh*t in the trash can. Admittedly I was using them on fuel and oil lines.

@ThePaintPaperHustle

2 жыл бұрын

Yea I haven’t purchased any for fuel I bought nice used ones for fuel to save money.

@gullreefclub

2 жыл бұрын

@@ThePaintPaperHustle Hopefully you will have much better luck than I did.

@ThePaintPaperHustle

2 жыл бұрын

We will see. Y’all know ima tell the truth and show everything good or bad

Where did you buy this kit?

@ThePaintPaperHustle

7 ай бұрын

eBay

The "American made" stuff is all Chinese... you're doing OK with this purchase bro

@ThePaintPaperHustle

2 ай бұрын

I 100% agree but a lot of people don’t so I choose my words carefully lol

😎

@ThePaintPaperHustle

2 жыл бұрын

👊🏻