I wished there was a video all about the transmission itself and all of the gears. How they all come apart and go back together again. Including the casings around them.

@802Projects

7 ай бұрын

I'd probably watch it too:) Maybe Chris from Revenge will do it

Superb video, thankyou for sharing that knowledge so thoroughly. Ive jsut had a 6 speed box rebuilt and a new Exedy clutch fitted, it feels way better but it crunches into second, unless I hold the clutch down for a little longer and pause before selecting the gear. I have a few places to start looking now, thank you! I am really hoping it is an adjustment or leaking slave or master cylinder rather than an issue with the rebuilt box.

Excellent video! Thank you. Lots of great info here.

Fantastic video loaded with information!

Awesome. Bursted my pressure plate and now I’m realizing I’m going to need to replace more than I thought…slave cylinder boot was full of fluid. Very educational video; makes it seem much more simple.

Very informative learnt 3 interesting things from this video that I will be checking. Thankyou for putting this up.

Thanks for the great video hard to find info on these cars .. I wanna know where did you get that book bc I want one

Can you please do a video on replacing crunchy synchro in the vr4 trans and your thoughts on rebuilding it?

You're a legend for making this. Getting to this point on my build soon. When you replace that output shaft seal do you remove the bellhousing?

@802Projects

Жыл бұрын

No. You can very carefully drive a pick, small screwdriver into it (make sure you don't scratch shaft or housing) and pry it out. The trans has to be out to do it. Even if you got the seal out with the trans in the car the teeth of the flywheel would prevent you from being able to slide it off.

Same here just put a Centric master an slave on mine, feeling pretty tight.

Nice video! You have already win a new subscriber 👍 What is the name or the ISBN of the book you are checking?

@802Projects

4 жыл бұрын

I don't have the IDBN number but it is the 1992-1996 Body - Chassis Service manual for the 3000gt. All of the OEM manuals are available for free on 3sx. www.3sx.com/tech-manuals-service-technical-reference. Page 545 of Volume 1 is the page I was looking at.

When I pump up my clutch adding fluid and hand pump the clutch to floor and hold it as I bled the slave. Close slave release pedal...repeat process till the lines are bleed of air. My pedal still feels easy to depress and about past half way down I start to feel some resistance where the throw out bearing is disengaging. It use to be at the top of pedal when clutch disengages. Now when I replaced the slave it's not at the same spot? Any idea what's going on?

What book are you using for the technical stuff?

Did only the Vr4 3000gt have a hydraulic clutch or did the Sl also have it?

🔥🔥

When you have a failed throw out bearing, did it make like a really loud squeal and like a weird sound when idling?

@802Projects

3 жыл бұрын

The TOB in my 93 vr4 makes a light chirping/squeel sound at idle. If I push in the clutch it goes away. Its been doing it for over a year now. Eventually I'm going to replace it but I've been holding off as I may just refreshen everything up seeing as its nearing 160k.

Really nice video. I will send it to the mechanic how put a new clutch on my 3000 GT VR4 1992. He replace my clutch but now after warming up the engine the clutch starts to be noise. Per happens if you get any suggestions it will be very appreciated!

@riscongo2010

Жыл бұрын

How much was the new clutch?

@besttourinrio9

Жыл бұрын

@@riscongo2010 U$120 US dollars

@riscongo2010

Жыл бұрын

For the mechanic to put it in?

@besttourinrio9

Жыл бұрын

@@riscongo2010 yes

Is it normal on the 3000gt to have to push the clutch pedal absolutely all the way down to the floor to shift?

@802Projects

2 жыл бұрын

Most clutches go to the floor to shift. Just go to a flat surface, take ebrake off and make sure car doesn't want to roll. Then put it in first gear, push clutch to the floor and rev it to 7k. Does the car want to creep forward? If so its dragging and you need to adjust something.

HOW DO YOU TAKE OUT THE SELECT LEVER SHOE???

@802Projects

3 жыл бұрын

You have to unbolt the bracket the linkage pivots on. 2x 12mm bolts if I recall.

What Wheels are those? And Size

@802Projects

Жыл бұрын

They are 18x9 +40mm offset enkei rp03s. I think they are discontinued now.

@antoniobrown5002

Жыл бұрын

@@802Projects Thanks Man and we all appreciate the info about ours transmissions! 👍

Are you on 3si?

@802Projects

2 жыл бұрын

Yes. Fastfalcon94