No video
Adjusting Andis T-Outliner Armiture For Precise Haircuts | Maximize Power and Performance
This video will describe how to adjust the armiture of you outliner trimmers so you can get the most power and best performance from your trimmers.
Snapchat: ayedeezy03
Twitter: realadthebarber
Instagram: realadthebarber
Periscope: realadthebarber
Пікірлер: 214
Maaaaan! I've been looking all over KZread and the Internet for this fix! Thank you for being straight forward and getting right into the fix too! I'm now a subscriber!
Suggestion. Use a feeler gauge in determining your optimum gap between the armature and the coil base. That way, when you have already determined your optimum gap (minimum noise and max cutting power), then when it's time you have to re-adjust your armature gap again, you already have your baseline/optimum distance as basis using a feeler gauge to set the proper gap fast and accurate. Hope this helps.
@victorcarr8055
Жыл бұрын
If you get the measurement for feeler gauge please post that'd be great
bro aint gonna lie, I was just about to throw my Andis in the garbage until I scroll through here and found your video and it helps so much now my machine is cutting brand new...thank you so much for making this video...
I have to break out the Denzel voice for this one ... "My Man!!" This video finally has my trimmers working the way they should be. I've had 5 sets of trimmers throughout my life. EIther they wouldn't cut close or they would cut too close or one side would be too sharp while the other was dull. I would take the trimmers apart and adjust the blades over and over and I would encounter the same problems. I saw your video and did what you said. I then preceded to give myself the best tape up I've ever had, including barbershops. They worked just as you said and how I Knew they should, with minimal effort. I had resorted to razors but now I can finally rely on my trimmers thanks to you. Thanks for the video!
@AdrinTheBarber
8 жыл бұрын
+DynamoDeniro Im glad that I could help you get them working correctly! Any questions you have let me know!
@CruiserzProductions
8 жыл бұрын
I know the feeling bro, I had to learn how to do it myself but i've just learned about the power screw, I thought it had to be tigtened to the brink lol
@nathannevaeh2323
7 жыл бұрын
ADTheBarber how do you adjust the arm if my hitters don't have the two black screws??
@RDTSMOOTH
7 жыл бұрын
Do you adjust clippers? If so how much and can I mail it?
@Crappie_Day
6 жыл бұрын
Yeaaa now you hooking people up reaaal good. Just don't start hitting up your eyebrows with it haha
Thank You! for your posts. The last couple months I've been fighting with my T-Outliner thinking it was blade alignment..nope..had that correct and down over the years of using it almost bought ne blades. DING DING my friend! Blade tension setting. Got that good! buzz back after watching and resetting. Thanks Again! Good Vids and only had to watch 2 both yours.
the two screws that you have to remove on the inside first . mine are more of a circular looking screw inside of two black screws , i can't figure out how to take it off
@chiefxx5250
3 ай бұрын
any chance you can share info on this? I got the same kind
You don't know how much this video helped me. Thanks AD.
i dont have the model with the screws :(((( please help
@JoseGarcia-ki4hn
3 жыл бұрын
???
@EFdee9
3 жыл бұрын
@@JoseGarcia-ki4hn there's a model that comes with two rivets, they usually are black or silver, i have the same one
Awesome video. Necessary information for a barber who wants the best out of his tools
@AdrinTheBarber
8 жыл бұрын
+CleanCutz Thanks! All about helping everyone succeed!
Oh no they arent the Wahls that i hear a lot about they are the Andis Slimline Pros that i hear a lot of people like. I got confused cuz i found a cordless Wahl trimmer that looks almost identical to the Slimline Pros n i get confused easily now after my brain surgury.Thanks for responding n for the vid on how to quiet down my t-outliners. I cant wait to fix them when i get back home from this trip. Keep up the good work man 👍🏽
@broadwaybarbershopjonmerin9248
8 жыл бұрын
the wahls r better anyway
Oh ok yea you know what it wasnt the Wahl i meant the Andis Slimline pro. I keep hearing great things about them. I just got them confused cuz they look similar but out of all the cordless trimmers ive seen or heard of the most common one ive been hearing about that everyone seems to like is the Andis Slimline Pro. Thanks for the help AD if you do end up piking one up please do a review im have a few questions like on run time, if they get hot quik and how loud they are.. Dunno if ill zerogap them cuz i wanted them mainly for kids but might just have to get 2 pairs to adjust to get that crisp line. Thank you for these vids really heping us aALL out
AD 👍🏽👍🏽👍🏽👍🏽THANKS BRUH I CUT MY OWN HAIR AND I WAS JUST ABOUT TO TRASH MY T OUTLINERS.... THANKS FOR THE INFO. I JUST SAVED ME 80 BUCKS....
Thanks definitely help my liners were dead before this video...🙏🏽
thanks for the video. i just adjusted my clippers and they work great! If you encounter clattering after adjusting, try loosening nut again, push up on the arm from where the triangle piece is where the screws go. lock the nut then put the two screws back on.
NEW MODEL HAS 2 ROUND HEAD STUDS & HEX SCREW NOW. 1/2023.
My new T outliner only has a center nut on the arm... the screws /attachments on either side are there but can’t be loosened anymore.
Thanks AD!! Im so glad that you did both the new and older t-outliner! The one that was giving me problems is the one i got from barber school 12 yrs ago so it helps that you did both. I appreciate you takin the time to make these vids to help us all out. Now im just looking into getting some battery powered clippers incase of a major blackout . Bout 3 years ago here in SD we had a major blackout that lasted almost 2 days n just so happened to be that i was just starting a HIGH skin taper wen the power shut off haha. Poor guy. But anyway thank you for this vid deffinately is gon help me fix my clipps wen i get home. Oh last thing- im most likely gon get either the cordless designers or the magic clips. But need a cordless trimer n most likely get the lithium ion by Wahl. Do you know if those can be adjusted? Not looking for a zero gap cus i wanna b able ta use them ine kids n itd just be safer but wud like to see if i can get them to cut a lil closer although i havent even used them
@AdrinTheBarber
8 жыл бұрын
+Louie Garza I really dont have to much knowledge on the cordless clippers since ive never really used them much. But after your experience you have me wanting to go and purchase some just to be on the safe side. But i do plan on reviewing cordless clippers in the future. Sorry
@louiegarza9689
8 жыл бұрын
+ADTheBarber Thanks!! Yea im just looking ta get a pair of pro cordless outliners. If you see or hear of any good ones please lemmee know :). Only ones i been hearing about lately are the Wahl lithium ions but dunno if they can be adjusted n i dunno how long they run off a single charge.Thanks for takin the time to respond. I deffinately appreciate it. Keep up the good work i was actually just watching another vid you posted on some other cordless clippers that wer kinda like the Oster 76s i think... Thanks AD
@Deancutit
8 жыл бұрын
+Louie Garza get the cordless magic clip and the slim line pro,great cordless combo
@louiegarza9689
8 жыл бұрын
+Donnie Dean thanks! Yea i just did actually.... I got a pair of the cordless magic clips and the slimline pro li's they work great! Love them already
Good job man. Saved my clippers
Tried this and it worked like a charm. Thanks!
Great tutorial Adrin! This was just what i need to see. My blades are off to the left. Thank you !
The cordless wahl magic clip is a beast. I can knock out 4 to 5 heads with it before t slows down, but so far it's never ran out in me.
@AdrinTheBarber
8 жыл бұрын
+magic7207 Yes thats great Ill definantly have to try it!
+adthebarber yooo bro, I went to try this and my trimmers don't have the Philips or star screw! it looks like a rivet! any suggestions
ur the only person I've seen mess with that arm thanks mqn
Hi,I have a problem. Instead you have the two black screws, I have two rivets.. The machine is noisy and I cant correct it because it has rivets.. What do you suggest I do?
@cavoreo
5 жыл бұрын
Fake trimmers
@geolocx
5 жыл бұрын
@@cavoreo stfu
Well I had my GTX cutting real nice, I saw this video and noticed my blade is off to the left and I thought I need to fix it. I adjusted it to the centered and I’m getting nothing but clacking sound now. If your trimmers are running fine leave them alone. This is not necessary.
Thanks a lot for the video, no one ever showed this too me, real one
Great video! Knowledge is power!
Do the flathead screws by the blade serve a purpose? Or the two screws for the housing? I adjusted mine and ever since I feel like they don’t hit the same especially when balding
Man I've always wondered why my blades kept cutting uneven I went through 3-4 outliners thinking mines was defects well I had the same problem with my current one but now I'm gonna fix it
Question bruh i opened mines just to take a look but in both your t-trims there were crews in mine though they have bolts & there's no way to take them out without breaking them so is my shit a knock off bootleg or what they still get the job done & I wish I could say I didn't feel shitted on
@FaLauren
8 жыл бұрын
bro you have a newer model.. they took the screws out of the newer ones so they cant be adjusted
Thanks bro nice and clear. Great tutorial. 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥
Dude this was so helpful. Thank you very much.
In this video I hear you saying one is old model and the other a new model and they both have armature plates with screws, the older one tightened with Phillip screws and the newer one with star screws,honestly I don't know which planet where mine is manufactured although it says Andis on it and it looks exactly the same like these two here because they have the same power switch but unfortunately the armature plate is riveted down so there is nothing that I can do to adjust the armature should anything goes wrong with it. The model number is Andis T Outliner Trimmer Gray Model GTO 04710. I just hope that it is manufactured in planet earth .
Mine is totally different the screw you have mine came with no screws or heads it's rather round.. the only thing it does have is the center screw
Any thoughts on those rivets yet? Mine has them as well. The arm seems off in comparison to this video, but not sure how to fix it. It makes me feel like I should return it.
I have a black t outliner and it has no black screws it just has 2 flat headed metal circles that you can't unscrew? The middle one to adjust the arm is still similar but why is mine different? Please respond as fast as you can...
@AdrinTheBarber
8 жыл бұрын
I will have to open mine and see, I think i know what you mean
@ivanrivas3464
8 жыл бұрын
+ADTheBarber thank you
@ogrewease
8 жыл бұрын
+ADTheBarber yea I got the same two rivets also. is there anyway to adjust them with those in place? and anyway one can tell how to not buy the ones with rivets?
@StevenSoto
7 жыл бұрын
yea my gtx is just like that idk how to adjust those
@jcuts831
7 жыл бұрын
Same problem is there anyway to adjust it ?
I was just about to to ask how to fix that noise, thanks.
Great video...I am trying to decide amongst the following machines: 1. Andis T-Outliner 2. Andis Outliner II 3. Andis GTX Can the T-Outliner blade be used on the Outliner II? What is the difference between the Outliner II and the T-Outliner? Is the GTX the best? Which one should I buy to give me the sharpest cut? Any advice?
@StevenSoto
7 жыл бұрын
I just got the Gtx today it is good
@thesuccessfulbarber
7 жыл бұрын
Mark Bromley the only difference between the outliner and the outliner 2 is the blade...( outliner 2 has narrower blade not a t blade) the only difference between the t outliner and the gtx is the color and the teeth on the blade
6.5mm socket and ratchet works best for that bolt
Good video How do you adjust for 220 voltage
great info. I would have never resolve that clattering noise or the uneven of the blades
So the factory off position is fixed to the left side. And the goal is to make the new off position fixed to the center.
@dominickalo6803
7 жыл бұрын
supa dupa I just got a pair a few days ago, it was set to the left side as well, so does that mean it's off?
@supadupa6891
7 жыл бұрын
dominick alo...... No. Thats the natural factory setting. Out the box, its to the left.
@dominickalo6803
7 жыл бұрын
supa dupa oh ok, so is it wise to set it in the center, like what's going on in this video?
This helped a bunch. Thank you.
My Andis maintains two studs oppose two black screws. Thus I'm unable to reposition the arm.
Mine don't have the two black screws. They have some sort of pins in the space
Thanks BigDogg well explained✊✌
Hey,bro I opened up my t outlines to clean them and in the process a part that look like a metal oval shape with a stem on it lol,I watched this video because you opened them up.i didn't see the piece..aby suggestions?
I dont have screws there just flat plates..........
@cavoreo
5 жыл бұрын
Fake trimmers
@dannyfarr106
5 жыл бұрын
Mine are the same I don’t have screws, is there anything you can do?
@asuas3115
4 жыл бұрын
Same I got the andis gtx & you can't unscrew them they really fucked up on those
@anthonyharris5928
3 жыл бұрын
Lol not fake. Model G has rivets instead of screws. I guess andis caught on to people extending the life of their product instead of buying a new one lol. 🤷♂️
Great tutorial thanks
Mine doesn’t have the two screws and it’s in a fixed position
Lol damn, mine has rivets (Model G). I guess andis caught on to people extending the life of their product instead of buying a new one
How do I adjust the armature on the new outliners? The old outliners had phillips head screws, and the new outliners looks like they have flush/rivets screws.
I have a set an the armature is actually touching the motor. It has really no room to play with as far as moving over. When I move over an it's not touching the motor then it's so far off that the blade is out of line with the tension arm. What could be the problem
Mi andis gtx t outliner aveces muerde el cabello y llega a arrancarlos, es nueva y no se si sea la cuchilla.
On the Motor Assembly why does the red cord break off on the grey side? You can get a New Andis Motor.
I knew my liner wasnt fried. My god i put my black GTX in the graveyard in my bottom metal rollingtool box years ago. Haha i just put a blade on it after i moved the arm a bit and now its HITTING without that loud noise. I used to turn it off QUICK thinking if i let that noise continue that it would fry my shit, i was trippen
What u do to make straight lines ? When I shape up a client hair line? Or zero gap it on the T outliners.
Why do ppl say to take out the bottom screw on the Andis t trimmers they sax it makes it stronger is that a fact ???
How you put the piece [on and off] back cus now i can make again..😔 color vino
What would cause the blade to no move at all? It’s as if the guard blade is pressed too tight and won’t allow movement. But if I adjust the tension any less the blades fall off. It’s driving me crazy. Any idea?
I got a pair of masters that stopped working. I plugged em in & they made loud clanging then stopped. Now they don't even power on. Any ideas? You think moving this arm could help in any way?
Is this considered over tuning the clipper or no
My bolts are flat? like with no grove for a phillips, it just has the hexagon screw in the middle, I got that out, but how do I take the other two out? it won't move and I don't want to mess it up, and I can't find a video to help, thanks if yall reply before I can figure it out
Can you do a tutorial on adjusting Andis masters so that they don't rattle as much, and are quiet?
Dropped my brothers liners and this video saved me $ 🤦🏽♂️😅
I purchased a new shell, installed all the pieces & it operates. I need some fine tuning, but can’t figure it out. I’m local to DC, any suggestions on where I can bring it to have it tuned?
hey on andis clippers,can you use any blade it dont have to be the t-outliner,can you just swap them out,with a different blade?
Mine doesn't have screws it's pressed in just flat.what do I do
Reduce, reuse, recycle… being n the game for 9 yeah anything that gets broken. You gotta crate a graveyard. I have so many screws, bodies, all kinda hardware, etc
My andis m3 styliner is super loud. Doesn't matter how much I play with that screw it didn't quiet it. It pushes the cutting blade to one side and stops it from moving. How can I fix this?
It’s weird mine have rivets instead of black screws
Mines don't have neither of those screws, they are flat on the top how do I get them out?
what is the purpose of the top 2 screws in the motor under the blade used for?
What does having the silver plate unscrewed do? I see you don't have those on your liners.
does the the two cover screws affect operation of the blades?
mine has two rivets instead of black screws. How do i adjust those ?
Thank you
How can I adjust my gtx model ,there is no screws, just a flat neither ph nor t15
I done adjusted mines like 8 times they still want cut... what now, do I need a new blade?
Nice video AD👍
good video bruh I appreciated you.
how can I make my clipper(whal super taper cordless) more stronger???????? REPLY
Excelente video
My shit still pulls but I cant do that since I have the newer kind I’ve only had these for a year I have sharpened blades and tension right and I have adjusted it 30 times if I press down on the blade it will just stop someone help this sucks
I have the new gtx and the blade is too far left when off
thanks barber brotha
My t outliers don't have 2 screws there rivits so I can't ajust my tension!!!! Is there something I don't know???? Someone pls help me😔
i just bought my first t outliner and i dont know what is wrong with them because i cant adjust the arm because it has no screws that i can unscrew because there is no spot for a screw driver to go into what do i do please help should I send them back or am i out of luck thanks
@FaLauren
8 жыл бұрын
sorry bro... they took the screw outta the newer ones so you really cant even adjust em
can i do this to any clipper i wanna do all mind.
Yo bro thank u so much I kept messing with the tension bar n my trimmers were still clattering. I adjusted the arm bar n I worked. Yo good looks😊
I tried to adjust and now my outliner wont cut... Any help???
I made a gauge to set the armature, no fuss, set it correct ervry time.
@bL3dbL4k
7 жыл бұрын
That's a good idea. What did you make it out of?
How do you clean your blades ?
Ok I have no two side screws they are rivets
thanks for the knowledge
🤔 I'll have to have a look. Nice work.
@AdrinTheBarber
8 жыл бұрын
+Mathieu Riesling Thanks!
@ryh4n890
8 жыл бұрын
I have a problem, I dropped the t-outliner and then the thing that holds the tension spring is kind of crooked how do I fix that?
yo AD, in the even newer model they took those screws out completely! >:| so u cant adjust them
@Drifter212
8 жыл бұрын
seriously?
@89sGift
8 жыл бұрын
+JEFF WILLIAMS yup !! Sucks.
@Drifter212
8 жыл бұрын
that sucks, I have a brand new set of the GTX model, and I'm going to check that out now!
These trimmers keep clogging on me with coarse hair, it’s so annoying cause it make my haircuts take longer
had a circular key looking piece that fell out as soon as I opened my clippers and I don't want to close it until i put it back where it was... do you know where it fell from??
@ldsams1
8 жыл бұрын
It goes in the slot where the thick piece from the power cord goes.. It's to hang the trimmers
@gabriel713281
8 жыл бұрын
+It's MULE thank you!
@ldsams1
8 жыл бұрын
+gabriel713281 no problem
the GTX is v5000 or v9000 ??