Пікірлер

• 
  @nvidiasniper5 күн бұрын

  Thanks for the hard work you'll put out to create this documentary

• 
  @TheAndicard11 күн бұрын

  Does anyone know how to turn the screen off to preserve power?? Thanks in advance

• 
  @susannordstrom5065Ай бұрын

  I managed to get the heater onto lo by pressing the OK twice, I find it confusing to operate, I just want it to tick over quietly, like my old heater used to do

• 
  @robertsimard735Ай бұрын

  Great saw and tutorial on them reed valves. May look into that for my saw.

• 
  @michaelh39942 ай бұрын

  Crap controller

• 
  @Vincegould2 ай бұрын

  Anyone got a good link to these donuts?

• 
  @josephpronovost91624 ай бұрын

  I'm installing mine tomorrow. I ordered an extra 3M of exhaust pipe and I'm going to take more heat out of the exhaust.

• 
  @PainterD544 ай бұрын

  Lets see, I'm going to get a diesel heater and burn waste oil in it. Why not just get a waste oil heater? It's a diesel heater. Why are so many people using waste oil when it does not work long term? How many videos are on here showing that it does not work? Why?

• 
  @jamiewall97894 ай бұрын

  How do you pair the black remote?

• 
  @jimschaffroth56524 ай бұрын

  Mine has the gold controller. It's slightly different. Anyone used it before?

• 
  @andykeen32094 ай бұрын

  It’s so wild how complicated this is. I think I’m terms of User interface usability, I’d prefer an entire keypad with many buttons, instead of the press-and-hold 2 buttons simultaneously. You almost need a masters degree for this, and I can’t just attribute that to the language barrier between Chinese and English either. Woosh, thanks for explaining it and sharing! I’ve spent 25 years as a software engineer, almost exclusively on User interfaces (“front end”) and I’m not a “user experience” expert, but this would be such an excellent interview challenge for UX designers. A gold mine, really. How would you design it better? What would you take away? What buttons would you add? Apple would do it nicely I’m sure. Steve Jobs, we need ya man!

• 
  @condell19564 ай бұрын

  Thank you you taught me a couple things that I didn't know.😊

• 
  @billfox64915 ай бұрын

  How far away will the remote work ?

• 
  @Krb01225 ай бұрын

  Did the reeds hold up? I had an old builder tell me if im gonna use the saw as a work saw, to leave the reed stop in so i dont get a snapped reed. He said if its gonna be a hot rod show runner, it was ok to leave the reed stop out. Just wondering how yours has held up over time. He explained how to tune the reeds as well, but mine gave such a huge boost in power that i was pleased enough to leave them as is with the reed stop in place. Mine is a 655BP with other mods as well.

• 
  @Storman775 ай бұрын

  Held up fine but I remember it’s a bit of a hot rod.

• 
  @d.j.robinson94245 ай бұрын

  I appreciate your tenacity, but it won't burn hit enough, but keep trying different ratios; however, you might wanna try a better math aye.😂👍🔥

• 
  @Storman775 ай бұрын

  It don’t run without constant cleaning

• 
  @SuperCyril25 ай бұрын

  What size line is the short black pieces?

• 
  @kennethwers5 ай бұрын

  The pump is a metering device(and pump). The heater uses a drip feed. The fuel is not sprayed into the heater. The type and length of the pipe does not make any different.

• 
  @jameshan74985 ай бұрын

  Great idea, best i've seen

• 
  @willf57685 ай бұрын

  You should run your fresh air intake outside becouse your useing air from inside the garage which if its air tight may be a problem.

• 
  @Storman775 ай бұрын

  I agree but I can 100% guarantee that the garage is not air tight. I can see little light here and there on main door.

• 
  @leviscott85195 ай бұрын

  Good tips on heat pump cleaning and small engine carbs! I need one of those ultrasonic cleaners! 😎🤙

• 
  @beverlyan5 ай бұрын

  I am a PR from Amazon brand and have been following your channel. I really enjoy your content and would like to collaborate with you. How can I get in touch with you?

• 
  @Storman775 ай бұрын

  If I want I can use affiliate link with Amazon if I choose. What you proposing

• 
  @beverlyan4 ай бұрын

  ​@@Storman77 If you want to use your affiliate link, I can apply to our company. Could you provide your email address or suggest another way to contact you so we can discuss the details.

• 
  @beverlyan4 ай бұрын

  @@Storman77 I can apply to the company if you could help us shoot a video🥰

• 
  @Storman774 ай бұрын

  @@beverlyan what do you need

• 
  @beverlyan4 ай бұрын

  @@Storman77 Could you please share your email address so that I can contact you with details? Thank you.

• 
  @davirtrucking90235 ай бұрын

  Hi everyone. I get a code that the fuel pump is not working. A completely new unit. Is it possible that the wires are mixed up + - or does it not matter for this pump?

• 
  @Storman775 ай бұрын

  Yes it’s possible. Does the panel light up? What’s the exact code number ?

• 
  @sorebackula90875 ай бұрын

  I have the same display and remote. Put it into OC1, press up arrow on the remote and never leaves “waiting”. Maybe I have a defective remote.

• 
  @neilbaker31515 ай бұрын

  Hi there, Thanks for your video, it’s helped me get to grips with setting the timer. Can you tell me how to choose between manual and auto when it starts up on the timer. Thank you ☺️ EDIT Also, after many attempts of going through the timer setting process, I find I have to press ok after setting the first timer for switching on, otherwise it reverts back to the previous time I had set. The biggest problem I’m finding though, is that the heater isn’t turning off using the second timer. When I go out to my garage, the timer is no longer showing and the heater is still running. The only time it shuts off with the timer, is if I set the timer while it’s running!

• 
  @Storman775 ай бұрын

  That’s weird . I would have to test on mine. I don’t use that feature

• 
  @PainterD545 ай бұрын

  You haven't learned by now that those heaters are not made to burn waste oil. They're diesel heaters, made to burn diesel! Waste oil is dirty, it even says "waste", so why do you think it should burn clean enough for that heater? Are you filtering it? Also, those heaters are NOT 8KW, they are barely 5KW so that's why they are all the same size. They lied about them being 8KW that's all.

• 
  @PainterD545 ай бұрын

  By all the videos on here it looks like if you filter your fuel, the heater will run longer without having it to be cleaned so often. Best thing to do is to replace the cheap green fuel line with some better quality line and install a filter between the tank and pump and you'll be good to go.

• 
  @TwoUpTourer5 ай бұрын

  Sound is poor, could not understand a lot of what's said.

• 
  @conceptsken15 ай бұрын

  Great video! My first day using it, I ran it for 10 hours, no problems. I never smelt anything till the shut down. This is a lot of bang for the buck. See how long it lasts?

• 
  @curtwuollet29125 ай бұрын

  To test. Plug into the unit and hit go. If it glows, its ok.

• 
  @Storman775 ай бұрын

  Well that’s not really scientific lol. But that would work

• 
  @hobbyguy796 ай бұрын

  Does anyone know how to confirm 12v or 24v function with this controller?

• 
  @Storman775 ай бұрын

  They usually work on both

• 
  @user-fe9bd7ec2r6 ай бұрын

  Sun of bti#$$#sht i got it now ! I forgot how much good old plumbing works ! Hey thanks for the info and videos 😊

• 
  @user-fe9bd7ec2r6 ай бұрын

  Where did you get that exhaust port through the garage door ? I want to do the same except through a wall of the garage ! I want to be safe !

• 
  @gbear10056 ай бұрын

  Recommendations 3of4 .. run unit completely inside the trailer with the ONLY exception the exhaust pipe. Sleeve the pipe where it exits the unit.. have a fan blowing on exhaust the whole time. Mount high enough that the exhaust is ALWAYS sloping or straight down. Never have a U or dead spot in the pipe.

• 
  @gbear10056 ай бұрын

  Reccomendations 2of4 mixture is very well filtered waste motor or veggie oil 40 percent, pure diesel 50 percent, 10 percent petrol. Start w pure, run on mixture, shut down on pure at HIGH for several minutes.

• 
  @gbear10056 ай бұрын

  Recommendations... part 1 of 4 two fuel sources, one pure diesel/heating oil/kerosene and the other your waste oil mix. Manifold together .. use pure to start and shut down.. mixture while running.

• 
  @hans-joergbecker39046 ай бұрын

  Hello ... My name is Hans i come from Germany , i have buyed me a brand new Diesel heater with te same display and have seen that i can not take the service code for the same old display my display shows similar that in your yideo . if You can help me with the service code , please send me them it is not four digits there are tree lines and i think it is an tree digit code . Best Regards Hans God bless you Please forgive me my english , i think thats not tooo good.

• 
  @matzstrom32236 ай бұрын

  i read that "short press ok and power button at same time, then put 3 digits code, not sure if it is 678 or 987, then you should be in fine tuning, let me know if it works . . .

• 
  @hans-joergbecker39046 ай бұрын

  Hello Good Man , i thank you for this fast Answer , but i have not make a test yet , But after the lunch i go into my garage , will make a test , when i have done Testrun then i Tell you , I hope the Codes are fine and i can adjust or make finetuning . Have a nice Day . Regards Hans

• 
  @matzstrom32236 ай бұрын

  @@hans-joergbecker3904 It looks like you can only see error codes (by use one of those codes) that have shown on screen before . . . . a video from Germany ( i do not speak the language) tells all codes, i try to post a link, and see if you can understand him

• 
  @matzstrom32236 ай бұрын

  @@hans-joergbecker3904 if they did nit let me post the link, search: 2023 Alle Displays alle neuen pins Matherbord mit 8 Kabel ? China Heizung Diesel Standheizung

• 
  @hans-joergbecker39046 ай бұрын

  @@matzstrom3223 Hello and thx for your quick help, I have now been to the workshop and tried both codes, but without success, it seems that the Chinese has once again changed the codes ,,,,,Now I am at a loss, is there another way to reduce the pump cycle (about 1.5 Hz) to less than 1 Hz ? 0.9 Hz would be ideal and completely sufficient for the required heat energy that the heating should supply

• 
  @johndoe52476 ай бұрын

  Do they make one of these with 80000 BTU and an exhaust pipe ?

• 
  @daledoherty88196 ай бұрын

  Does it smell?

• 
  @Storman775 ай бұрын

  Not one bit except on start up

• 
  @3genac6 ай бұрын

  Other controllers can set range for pump rate in Hz and fan RPM to accommodate incremental elevation change. Can this controller act similarly? How if so? What does Alpine mode do exactly? Unless it senses specific elevation, I can't see how a single alpine setting could accommodate elevation changes over hundreds of meters. I hear pump slow, but a fixed setting can't suit 1500 AND 3000 meters. I'm getting white stinky smoke at 1500m elevation with new 2km unit, which had worked fine here for a few weeks. Alpine mode doesn't help. Consensus: mix is the problem, so advice is to alter pump Hz and fan RPM. HELP thx and hny.

• 
  @matzstrom32236 ай бұрын

  i read that "short press ok and power button at same time, then put 3 digits code, not sure if it is 678 or 987, then you should be in fine tuning, let me know if it works . . .

• 
  @3genac6 ай бұрын

  I believe other have corroborated the procedure you describe; sadly the menu displayed subsequently reveals superficial data and not fuel-air mix control. Thanks anyway!

• 
  @Storman775 ай бұрын

  No

• 
  @3genac5 ай бұрын

  My new VEVOR comes with an actual elevation mode that senses barometric pressure. Wish me luck.

• 
  @herschelgant6486 ай бұрын

  Looking to do this. Right now I use a humongous diesel salamander. It kicks off and on as needed. I use about 7 gallons of diesel fuel per week to keep an uninsulated 20 x 20 garage 65 to 70. That’s with it getting cold outside. Do you think something this small would keep up with that?

• 
  @Storman775 ай бұрын

  You’d be burning same amount but way quieter. You’d have to run full out

• 
  @crankshaft0076 ай бұрын

  Anyone else know if you can use HZ mode ?

• 
  @matzstrom32236 ай бұрын

  I read that "short press ok and power button at same time, then put 3 digits code, not sure if it is 678 or 987, then you should be in fine tuning, let me know if it works . . .

• 
  @Storman775 ай бұрын

  Not this model

• 
  @curtwuollet29126 ай бұрын

  Interesting, but there are a lot of things in used motor oil that simply won't burn at normal temperatures. Even without the soot, there is a lot of residue.

• 
  @gizmo12520006 ай бұрын

  12 months later ,and im watching this video again norm ,thinking ,would Electrolysis work ??????

• 
  @Storman775 ай бұрын

  Ummmmm interesting. I’ll do some research

• 
  @jackhandyy6 ай бұрын

  Are you starting it on this oil mix??

• 
  @aceonp66006 ай бұрын

  All that crap and shit you done to it lol

• 
  @clem956277 ай бұрын

  Good video showing the Timber Tough. I have one and use it in combination with my Granberg mill. Its much quicker on the set up for the slab cuts.

• 
  @jamesward57217 ай бұрын

  Meh - easy way is to grab a hoover, stick the nozzzle onto the exhaust & let it suck.It will clean out the combustion chamber enough that if you wisely refilled the tank with fresh diesel, the heater will refire - it may take a few goes. Then learn & only fill these delicate machines with fresh diesel - they are NOT waste oil burners, It not verk. For 10 minutes after it finally refires, you will have ALL the smoke btw - it clears eventually. These run for c.a 30 hours on any old muck - then they crap the bed. Use fresh fuel & run it on setting 1 - thank me later.

• 
  @chrisbradley94337 ай бұрын

  I burn old engine oil and a third old oil is the best mix I found .tried 50 ,50 and maintenance is high .take heater apart every two days of use.

• 
  @TheAllSeeingAye7 ай бұрын

  Can you set the fuel to air ration with this controller? If you hold the OK and Power button you get a setting that starts at 000 - what is that?

• 
  @matzstrom32236 ай бұрын

  you need to put the code then you get in to tune the fan/fuel

• 
  @DanFisher25 ай бұрын

  Anyone know this code? Not looking forward to going through 999 digits

• 
  @matzstrom32235 ай бұрын

  @@DanFisher2 They have already get through the 999 digits, only 678 and 987 get you in but then we do not know witch button combination code, you need to press or . . , my User manual for this controller is s....t, look like it missing some pages . . . 😞 I give up on that for now . . .

• 
  @conradcoolerfiend7 ай бұрын

  To prime the pump hold both arrow buttons down. When you let go it will stop priming. Also, for anyone curious, the timer can be set and engaged in the on and off modes. If you engage it when it’s in the on mode, the off timer will engage. And vice versa. You cannot get it to say, turn off and then turn back on without touching it. It will only do the one timer action before you have to turn the timer function back on to get it to do another.