Chinese Diesel heater cleaning with oven cleaner after waste oil use.
I used oven cleaner to clean my burner tube to get the dirt I couldn’t with many other products.
Жүктеу.....
Пікірлер: 51
@englishrupe01 Жыл бұрын
Glad it worked fine, Storm. It was the other side/big chamber that i was worried about the reaction with the cleaner. Thanks for the video.
@DirectCurrent4u Жыл бұрын
Your burner chambers are all made out of Stainless Steel. Keep up the good work!👍
@MrKyled81 Жыл бұрын
Could just use gravity to filter the oil. Used oil container about table height, hose through the bottom of the container, with the filter below that and a filtered oil container at ground level. It’ll be slow filtering. But you won’t have to worry about charging batteries or pumps failing.
@dovydasvoinickis452 Жыл бұрын
Low temperature cause lots of black build up in your heater core. Im burning it on max temp and its help to prevent cloging. Burned 15 liters of 70/30 mix with gasoline and it works fine
@andyhermiz3075
Жыл бұрын
30 gasoline and 70 waste oil? What kind of waste oil do you use
@andyhermiz3075
Жыл бұрын
Isn't that to much gasoline??
@allenstratton5399 Жыл бұрын
I will be trying the oven cleaner on my next clean out. I got so frustrated with the Vevor that I purchased a whole spare unit off Ebay for $89.00 delivered :) That one works so much better, and when I look at the combustion chamber I noticed that the no name unit had bigger slots in the combustion chamber that the one that came with the Vevor. I am going to find a way to get more air into the unit some how as I think that is major issue with the fouling out and building up of the nasty carbon. Thank you for the video's and all your hard work.
@roastntoast7550 Жыл бұрын
Helpful Video. Thanks!
@danya822 Жыл бұрын
If I recall you cant adjust the factory settings in this setup. Guy burning hydraulic fluid found that it seemed to burn best (highest heat, most stable combustion chamber temp) at a setting towards max, and well above minimum. But it wasn't at max. Different fuels will likely find similar stability at different settings. kzread.info/dash/bejne/ZJ970Nqklcyth6w.html Also, "filter bags" for biodiesel manufacturing are relatively cheap and MUCH better micron (from 1 micron up) filtering than most all automotive oil filters. I expect getting as much crud as possible out of the waste oil will help prevent crud building up as it burns.
@oliver90owner Жыл бұрын
The burner tube is stainless steel. The oil filter, if automobile, will be about 5-10 microns, so won’t remove much more than the larger particles and not much of any carbon that has been carried in suspension by the detergent oil. In old engines, which used non-detergent oils, the larger particles often collected as sludge in the crank case etc. many engines relied on that separation, hoping that most sludge was removed at regular oil changes.
@BeeHiverson Жыл бұрын
Very interesting. Nice video sir!
@nitrosrt4 Жыл бұрын
wow thats really hot, and interesting what the controller says. just measured mine same way, only 350F, seems to be chooching along quite well though. takes a few tries to start when cold, im blocking the hot air outlet to try and keep some heat in the unit, then ill disconnect the power when the glow plug turns off and start fresh with a bit more heat in the unit, keep the outlet blocked til 200C then switch to waste all day, the mix right now is about 40/40/20 waste/diesel/gas. when time comes to take it apart i want to figure out a way to put a second glow plug i can manually control, or maybe the afterburner has that kind of control. also gonna dilute my diesel with gas, maybe up to 50/50, the gas does make a different noise because it burns different but i think itll help with viscosity/gelling. if it werent for the trying to get rid of all this waste oil i'd probably just run 50/50 gas/diesel, seems like it may be one of the cleaner burns.
@andyhermiz3075 Жыл бұрын
Hey why won't you put the Exhaust in a 55 gallon barrel to capture more heat before existing that out?
@johncollinsgrove1750 Жыл бұрын
Try to point the heater down. May help the contamination build up from collecting at lower section of burner and let it go out the end of the burner and out the exhaust.
@GordonTurnerr
Жыл бұрын
thats a good idea!
@nutec6034 Жыл бұрын
Would pre-heat the waste oil help cleaner burning? Suggest use a metalmesh protected fueltube, and let align it next to the exhaust-tube back and fort. this should heat it up to 60-80 degree.
@colinhamer6506 Жыл бұрын
for filtering the oil instead of using a pump put the oil into a old gas bottle or similar and use comprest air to push it through the filter
@Bioengineered_NanoTech Жыл бұрын
Loving the experimentation on this channel. Any idea yet what the Advanced Settings code is for the blue controller?
@moonface957 Жыл бұрын
after filtering ,with the oil in a centrifuge. then you can change the mixture to diesel 25/75 waste oil (Black Diesel)!!!😉
@mobiusx8117 Жыл бұрын
@15:05 Looking good. Keep it hot.
@99diesel250 Жыл бұрын
Any word yet on that 3 digit code to access pump and fan settings?
@randywashing298 Жыл бұрын
Hey Storm what if u added seaform to oil mix
@andrewcurtis8174 Жыл бұрын
Have you done any with veg oil mixture?
@englishrupe01 Жыл бұрын
My intention/hope is that i can run 25% waste oil with 75% kerosene as i have plenty of both free. Thanks for the testing.
I've always used brake or carb cleaner to clean the diesel heater.
@englishrupe01
Жыл бұрын
Do you burn waste oil, too?
@powernosgaragebobiras3107 Жыл бұрын
How you make it to burn that hot ? Mine doesn't pass 300F I see yours its pass 500F
@Storman77
Жыл бұрын
I actually think the temp sensor sends a lower temperature to the board and allows my unit to burn hotter. It only happens on one of my units . The regular diesel burn unit hardly gets over 425 F . My question to you is , what KW is your unit ?
@powernosgaragebobiras3107
Жыл бұрын
@Storm Norm Leduc it supposed to be 8kw
@lanceulbrich6249 Жыл бұрын
Filtering the oil will help but not as much as you would think most of the stuff you see in the burner is metals put into the oil to reduce engine wear and are so small they won't come out with standard filtration
@walleyeye10 ай бұрын
Where do u get spare parts for those?
@larshartaalauritzen7039 Жыл бұрын
Hvor kan man købe den del hvor du kan sætte oliefilter på? Og hvad kaldes den?
@Storman77
Жыл бұрын
Filter head . Local tractor store or industrial supply store.
@andyhermiz3075 Жыл бұрын
Does oil burn better when you heat it up also are you burning sythatic oil?
@Storman77
Жыл бұрын
Yes and yes
@andyhermiz3075 Жыл бұрын
Why don't you run it on full desiel to get it up to temp the switch to the black deseil you get less build up?
@Storman77
Жыл бұрын
You haven’t watched all my videos ? I do get it up to temp on diesel
@KD0LRG Жыл бұрын
Just get a water filter to polish the oil.
@bearupfarm1818 Жыл бұрын
Were did you buy the new parts
@Storman77
Жыл бұрын
Amazon and eBay
@tracymacdonald4598 Жыл бұрын
I bought a cheap fuel pump off eBay and ran it through a fuel filter like what you have to polish the fuel in my boat
@arthurfoyt6727 Жыл бұрын
The heater is basically a diesel engine. Why not just use Sea Foam in the fuel and let it clean itself as it runs?
@Storman77
Жыл бұрын
I will try even though I don’t have that much faith in Sea foam I am willing to try
@Storman77
Жыл бұрын
And Arthur, this engine isn’t a heat pump like a true diesel engine . There is no compression chamber ignition it’s only basically a flame torch with diesel poured through an atomizing screen. But I will try it anyway 👍
@arthurfoyt6727
Жыл бұрын
@@Storman77 It's passive; just have it in your fuel and it self-cleans. No mess, no fuss ;-)
Пікірлер: 51
Glad it worked fine, Storm. It was the other side/big chamber that i was worried about the reaction with the cleaner. Thanks for the video.
Your burner chambers are all made out of Stainless Steel. Keep up the good work!👍
Could just use gravity to filter the oil. Used oil container about table height, hose through the bottom of the container, with the filter below that and a filtered oil container at ground level. It’ll be slow filtering. But you won’t have to worry about charging batteries or pumps failing.
Low temperature cause lots of black build up in your heater core. Im burning it on max temp and its help to prevent cloging. Burned 15 liters of 70/30 mix with gasoline and it works fine
@andyhermiz3075
Жыл бұрын
30 gasoline and 70 waste oil? What kind of waste oil do you use
@andyhermiz3075
Жыл бұрын
Isn't that to much gasoline??
I will be trying the oven cleaner on my next clean out. I got so frustrated with the Vevor that I purchased a whole spare unit off Ebay for $89.00 delivered :) That one works so much better, and when I look at the combustion chamber I noticed that the no name unit had bigger slots in the combustion chamber that the one that came with the Vevor. I am going to find a way to get more air into the unit some how as I think that is major issue with the fouling out and building up of the nasty carbon. Thank you for the video's and all your hard work.
Helpful Video. Thanks!
If I recall you cant adjust the factory settings in this setup. Guy burning hydraulic fluid found that it seemed to burn best (highest heat, most stable combustion chamber temp) at a setting towards max, and well above minimum. But it wasn't at max. Different fuels will likely find similar stability at different settings. kzread.info/dash/bejne/ZJ970Nqklcyth6w.html Also, "filter bags" for biodiesel manufacturing are relatively cheap and MUCH better micron (from 1 micron up) filtering than most all automotive oil filters. I expect getting as much crud as possible out of the waste oil will help prevent crud building up as it burns.
The burner tube is stainless steel. The oil filter, if automobile, will be about 5-10 microns, so won’t remove much more than the larger particles and not much of any carbon that has been carried in suspension by the detergent oil. In old engines, which used non-detergent oils, the larger particles often collected as sludge in the crank case etc. many engines relied on that separation, hoping that most sludge was removed at regular oil changes.
Very interesting. Nice video sir!
wow thats really hot, and interesting what the controller says. just measured mine same way, only 350F, seems to be chooching along quite well though. takes a few tries to start when cold, im blocking the hot air outlet to try and keep some heat in the unit, then ill disconnect the power when the glow plug turns off and start fresh with a bit more heat in the unit, keep the outlet blocked til 200C then switch to waste all day, the mix right now is about 40/40/20 waste/diesel/gas. when time comes to take it apart i want to figure out a way to put a second glow plug i can manually control, or maybe the afterburner has that kind of control. also gonna dilute my diesel with gas, maybe up to 50/50, the gas does make a different noise because it burns different but i think itll help with viscosity/gelling. if it werent for the trying to get rid of all this waste oil i'd probably just run 50/50 gas/diesel, seems like it may be one of the cleaner burns.
Hey why won't you put the Exhaust in a 55 gallon barrel to capture more heat before existing that out?
Try to point the heater down. May help the contamination build up from collecting at lower section of burner and let it go out the end of the burner and out the exhaust.
@GordonTurnerr
Жыл бұрын
thats a good idea!
Would pre-heat the waste oil help cleaner burning? Suggest use a metalmesh protected fueltube, and let align it next to the exhaust-tube back and fort. this should heat it up to 60-80 degree.
for filtering the oil instead of using a pump put the oil into a old gas bottle or similar and use comprest air to push it through the filter
Loving the experimentation on this channel. Any idea yet what the Advanced Settings code is for the blue controller?
after filtering ,with the oil in a centrifuge. then you can change the mixture to diesel 25/75 waste oil (Black Diesel)!!!😉
@15:05 Looking good. Keep it hot.
Any word yet on that 3 digit code to access pump and fan settings?
Hey Storm what if u added seaform to oil mix
Have you done any with veg oil mixture?
My intention/hope is that i can run 25% waste oil with 75% kerosene as i have plenty of both free. Thanks for the testing.
@wallacegrommet9343
Жыл бұрын
Kerosene reportedly keeps these heaters clean internally. Lower heat energy, though.
Does this burn used synthetic oils??
I've always used brake or carb cleaner to clean the diesel heater.
@englishrupe01
Жыл бұрын
Do you burn waste oil, too?
How you make it to burn that hot ? Mine doesn't pass 300F I see yours its pass 500F
@Storman77
Жыл бұрын
I actually think the temp sensor sends a lower temperature to the board and allows my unit to burn hotter. It only happens on one of my units . The regular diesel burn unit hardly gets over 425 F . My question to you is , what KW is your unit ?
@powernosgaragebobiras3107
Жыл бұрын
@Storm Norm Leduc it supposed to be 8kw
Filtering the oil will help but not as much as you would think most of the stuff you see in the burner is metals put into the oil to reduce engine wear and are so small they won't come out with standard filtration
Where do u get spare parts for those?
Hvor kan man købe den del hvor du kan sætte oliefilter på? Og hvad kaldes den?
@Storman77
Жыл бұрын
Filter head . Local tractor store or industrial supply store.
Does oil burn better when you heat it up also are you burning sythatic oil?
@Storman77
Жыл бұрын
Yes and yes
Why don't you run it on full desiel to get it up to temp the switch to the black deseil you get less build up?
@Storman77
Жыл бұрын
You haven’t watched all my videos ? I do get it up to temp on diesel
Just get a water filter to polish the oil.
Were did you buy the new parts
@Storman77
Жыл бұрын
Amazon and eBay
I bought a cheap fuel pump off eBay and ran it through a fuel filter like what you have to polish the fuel in my boat
The heater is basically a diesel engine. Why not just use Sea Foam in the fuel and let it clean itself as it runs?
@Storman77
Жыл бұрын
I will try even though I don’t have that much faith in Sea foam I am willing to try
@Storman77
Жыл бұрын
And Arthur, this engine isn’t a heat pump like a true diesel engine . There is no compression chamber ignition it’s only basically a flame torch with diesel poured through an atomizing screen. But I will try it anyway 👍
@arthurfoyt6727
Жыл бұрын
@@Storman77 It's passive; just have it in your fuel and it self-cleans. No mess, no fuss ;-)