At Home Vlog - by Jani Voutilainen
At Home Vlog - by Jani Voutilainen
Welcome to my KZread-Channel!
My purpose is to encourage people to do things themselves!
Plus, this is a nice hobby for myself.
Doing it yourself and editing videos is a nice pastime and hobby. And especially for cars and motorcycles you can save comfortably on maintenance costs.
Although sometimes it may go a little over maintenance 😉
I’m not a professional with cars or motorcycles, I just want to learn how to do things myself.
Hopefully these videos will be useful to others as well.
If you do these services yourself, always check the repair instructions for how to do it.
This is just my way of doing it!
Subscribe channel:
kzread.info
Social media:
instagram.com/voutilainenjani/
facebook.com/jani.voutilainen
vm.tiktok.com/ZMLosk5o3/
Best Regards,
Jani Voutilainen
#BMW #E91 #N43 #F20 #N13 #R1150R #CATIO
Пікірлер
My 116i is overheating it says coolant level low and drivetrain full performance not available I tried changing the waterpump is it likely it’s the thermostat?
Bonjour ma bmw ne demarre plus ou tres tres mal et me donne en code defaut 2af2 2af4 2af6 en court circuit vous pensez que sa vient de la sonde nox?les bobines allumage et bougie sont neuve
Where did you get the ista on tablet that will be great to have thanks
Ich habe nach gemacht aber gerüsche nicht wig nur wing geworden muss mann die mutter vorne mit richtig NM tziehn Verschwendung arbeit ich muss nochmal machen beim exbert
It's a bit of a glorified zoo cage, but it must be a treat for an indoor kitty.
Hey Jani. I have a VERY slow clutch fluid (DOT4) leak on my 2003 K1200GT. One drop evert couple of hours. What are the part numbers for the clutch slave cylinder SEALS for the rebuild? I thought that my DOT4 leak was coming from the hydraulic line crush washers that I gently disturbed when replacing my broken/cracked/deteriorated gear shift indicator switch. So I replaced the crush washers and I still have a very gentle drip.
What are the part numbers for the replacement seals?
We don't need the music.
Thank you! I did exactly how you did and it worked ❤
What to do when the car wont keep on and runs for a few seconds and dies?
Проверяются эти форсунки легко. По нику можно посмотреть проблеммы.
Hello! Thanks! for a very good Video. I have a Bmw 318i Petrol With Automatic gearbox. When I back the car out of the garage, the automatic transmission wants to drive the car very much, backwards. I feel like it's way too high Idling then. I have to press the brake pedal when reversing so they don't reverse too fast. Do you know anything about what could be wrong with this. They are Year Model 2006 on the Car. Thanks! From Tommy Bertilsson from Sweden
How do you maintane the grass in their area?
wow awesome catio
Your opinion?
Love your video!!!
Hello, I am thinking of installing this variant in a standard chassis, the plans may include lower springs. BILSTEIN 19-218014. maybe they are shorter than the standard shock absorber?
How did you lock the crank for torque the crankshaft bolt? Only by fly wheel lock pin?
Your cat is so cute and happy.❤
Love this catio . Great job. Have fun kitty's. Enjoy❤ .
Bro, do I need to code the injectors after replacing them? I see no option in my Foxwell.
Quick question when doing this test one by one do you hand tighten they spark plug just abit or torque them to spec as you do one by one or you do that once all test is done.
hey good work how to adjust the Crank position with the camshaft ,
Wenn man jetzt nicht selber einleiten würde. Wir sehen die Werte dann aus wenn man über 110 kmh fährt und temperatur auch über 590 Grad ist geht der nox Wert nicht runter? Also wenn man ganz normal auf der Autobahn fährt
How did you get the deck so clean? was it skimmed? or sanded, great vid, doing the same process, total rebuild, 👍👍
"For motor N43: Cam of release bearing (A = 12mm) is on sliding surface of release lever" And for the n46b20 engines?
Kann man den auch mit inpa codieren?
That is so helpful video could you please tell us how much it cost? And can u do it for me mine has same issue too I have bmw 116i 2005
Im about to replace my timing chain 250t km, the crank seal has no leaks, is there any reason to change it ?
Moro, onko järkeä tehdä vaihtoa vielä jos ääntä ei tosiaan vielä kuulu?
My chickens and cats would fight over it!
Hi Jani, did you find the fault? I also have a fault indicating the CCV in the rocker cover but I am not convinced the cover has a CCV! I say that as there is no resistance when blowing or sucking on the outlet. I tried this on the old cover and 2 new covers
Fixed. Thank you!
did you have the block and head skimmed?
Very good job on showing all the steps you need to take it apart and fix the problem.
Does anyone know about non return valves for the Vanos on a 2008 N43 318i engine? I've previously cleaned the Vanos solenoids at the front of the engine. But I've heard about non return valves having blocked filters causing hesitation, stalling and check engine light on other engines, and suspect I have this problem? Where are they and how to access? Any advice appreciated.
Good Job. Info please: the Gasket Rings and the Caps for all, MOtor, Gear and Drive, can you provide the size?. The ones you mentioned Ithink are BMW parts Number....
hi. there Does BMW F20 (N13), HIGH OIL CONSUMPTION the key factor is the piston oil scrape rings design issue, not only just replace the valve stem seals?
kiitos etukäteen ja hienosta videosta. Kertoisitko? Saisiko lainattua jostakin BMW N13 ajoitus , lukitus työkalut? vai onko pakko ostaa?
By the way how is this diff holding uo after rebuild ?
You dont change this green cable ? From mass
Ich habe es noch nie gemacht. aber wenn er es kann, kann ich es bestimmt auch.
Voiko ajaa pikku vaihteella ja hitaammin? Kun ei nyt voi motarilla ajaa 120kmh......
Have you found out what oil consumption was due to?
Hey great video. Does it matter if one shock is oil pressure and the other gas?
Thank you your video was a very helpful
Kiitos videosta! Tilaan tuon työkalun ja mittaan N47D20C koneen tilanteen. Kilsoja on 344tkm ja merkintöjä ketjun vaihdosta ei ole, joten vähän jännittää :D
Спасибо друг начну делать свой мотор буду пользоваться видео как инструкция руководство
Thank you.
Everybody waiting answers but the guy doesn’t reply...i heve the same oil consumption problem. The replacement of valve stem seals didn’t solve the oil consumption problem. Sorry to not be able to help you...