Awesome video! About to do my Kodiak, thank you very much
@mikenike7764 жыл бұрын
when you check the oil level it says in the manual to not screw it in but to set it in the hole and pull it out this is how ive always done it and tightening the camshaft gear can be tricky also i hate that part i worry about ruining the brand new one
@AgricultureINDIA-915 жыл бұрын
Super film!!!:-)
@joepalmer24043 жыл бұрын
Super thanks for posting
@AdrenalineRushMX4 жыл бұрын
that drain bolt lol
@Smalltechguy3 жыл бұрын
You are the MAN, I have been looking for videos just like yours. Nobody else has done one. I believe this 2004 bruin is off time. The lines do not match up on the cam or the crank. When I see the T on the cam, I don't see the tick mark on the crank. It's so hard to pull like its going to rip my arm out of socket. Plus this ignition is weird. I've ordered a new start switch in hopes that it will work. Do you have a video going over the wiring harness by chance??? Thanks
@awdman6214
3 жыл бұрын
Hey Paul, did you find out why your machine was pulling so hard? I have a big bear 400 timed correct but can barley pull it over.
@sukedk2001
Жыл бұрын
i just find the error on my kodiak ... the key for flywheel where broken i cant pull the line-pull and the starter strugle with driving it
@israelzerpa9844 жыл бұрын
Good Video, where do I can get the manual
@urabura96904 жыл бұрын
Hej. Proszę Cię o pomoc. Jak ustawiłem rozrząd? Na walku na znakach to wiem a dolne koło? Tam jest w 350 znak I i H (w poziomie?) na który znak ustawiłem? Pozdrawiam
@martinflashgordon
4 жыл бұрын
1:11 miałem znak "T"
@urabura9690
4 жыл бұрын
@@martinflashgordon w instrukcji opisane jako T ale fizycznie nabite na kole I??
@martinflashgordon
4 жыл бұрын
@@urabura9690 chyba tak jak mówisz, musiałbyś oglądnąć tą część filmu i może następną dokładnie w jakości 4k, bo o ile sobie przypominam to wkładam tam kamerę blisko i dobrze widać, ale ni mam czasu szukać, sam musisz poszukać
@tylerstaten4518 Жыл бұрын
Can you put a link of the papers you had in the comments
@JorgeMartinez-zc5fk Жыл бұрын
How can I get the service manual
@izaiaspedro19462 жыл бұрын
Oi moro no Brasil tenho um yamaha grizzly, aqui não tem mão de obra qualificada pra fazer o serviço, tem como disponibilizar esse pdf manual de serviço no Brasil não tem e meu grizzly está com mal funcionamento.
@samsungcoreprime48445 жыл бұрын
czy mógłbyś mówić po polsku bo w tym języku masz najwięcej widzów
@martinflashgordon
5 жыл бұрын
Chciałbym także trochę widzów zza oceanów i mórz. Wy także poznacie trochę angielskiego technicznego. Wszyscy na tym skorzystamy.
@mjshuja19482 жыл бұрын
Why don’t you DROPED CHAINE TENSIONER OK
@richwilliams97702 жыл бұрын
Is briun 350 done same way
@champton4260
Ай бұрын
Buddy imo the feds have removed all info on the bruin 350 from the net 😂😭😭😭
Пікірлер: 22
Awesome video! About to do my Kodiak, thank you very much
when you check the oil level it says in the manual to not screw it in but to set it in the hole and pull it out this is how ive always done it and tightening the camshaft gear can be tricky also i hate that part i worry about ruining the brand new one
Super film!!!:-)
Super thanks for posting
that drain bolt lol
You are the MAN, I have been looking for videos just like yours. Nobody else has done one. I believe this 2004 bruin is off time. The lines do not match up on the cam or the crank. When I see the T on the cam, I don't see the tick mark on the crank. It's so hard to pull like its going to rip my arm out of socket. Plus this ignition is weird. I've ordered a new start switch in hopes that it will work. Do you have a video going over the wiring harness by chance??? Thanks
@awdman6214
3 жыл бұрын
Hey Paul, did you find out why your machine was pulling so hard? I have a big bear 400 timed correct but can barley pull it over.
@sukedk2001
Жыл бұрын
i just find the error on my kodiak ... the key for flywheel where broken i cant pull the line-pull and the starter strugle with driving it
Good Video, where do I can get the manual
Hej. Proszę Cię o pomoc. Jak ustawiłem rozrząd? Na walku na znakach to wiem a dolne koło? Tam jest w 350 znak I i H (w poziomie?) na który znak ustawiłem? Pozdrawiam
@martinflashgordon
4 жыл бұрын
1:11 miałem znak "T"
@urabura9690
4 жыл бұрын
@@martinflashgordon w instrukcji opisane jako T ale fizycznie nabite na kole I??
@martinflashgordon
4 жыл бұрын
@@urabura9690 chyba tak jak mówisz, musiałbyś oglądnąć tą część filmu i może następną dokładnie w jakości 4k, bo o ile sobie przypominam to wkładam tam kamerę blisko i dobrze widać, ale ni mam czasu szukać, sam musisz poszukać
Can you put a link of the papers you had in the comments
How can I get the service manual
Oi moro no Brasil tenho um yamaha grizzly, aqui não tem mão de obra qualificada pra fazer o serviço, tem como disponibilizar esse pdf manual de serviço no Brasil não tem e meu grizzly está com mal funcionamento.
czy mógłbyś mówić po polsku bo w tym języku masz najwięcej widzów
@martinflashgordon
5 жыл бұрын
Chciałbym także trochę widzów zza oceanów i mórz. Wy także poznacie trochę angielskiego technicznego. Wszyscy na tym skorzystamy.
Why don’t you DROPED CHAINE TENSIONER OK
Is briun 350 done same way
@champton4260
Ай бұрын
Buddy imo the feds have removed all info on the bruin 350 from the net 😂😭😭😭
Skip dads