2003 kodiak 400 top end rebuild. Part 2. Engine timing.
Жүктеу.....
Пікірлер: 18
@CarverMacleodАй бұрын
Thanks for the help! BTW The kid is hilarious :)
@williamhawkins88016 ай бұрын
Good job letting your little one help. I miss those days with my son. He is all grown up and working on helicopters in the Marine corps now.
@bengrosser8722 Жыл бұрын
Nice video got the timing right the first time on my 01
@rolandsgarage8640
Жыл бұрын
Good deal I could help.
@jackedwards21292 жыл бұрын
You got a young Mechanic there...~Listen ~how he says My Turn that's it ,, he is serious,,
@rolandsgarage8640
2 жыл бұрын
Yes sir. I've told my wife that he will be my gear head
@joeschutze44753 жыл бұрын
hey, I just got my 2003 Kodiak back together after rebuild. It runs great but there is still a loud clicking in the head. I set the valve clearances. any idea what it could be?
@rolandsgarage8640
3 жыл бұрын
It's probably the valves. Make sure you get the motor warm and put it on top dead center and adjust them again
@jamespatterson7292 жыл бұрын
after finding top dead center and setting up the timeing chain on marks flywheel and top end on mark . when trying to crank it , pops or back fires out the intake ?? am i 180 out ?
@rolandsgarage8640
2 жыл бұрын
Yea it pops through the carb your 180 out
@jamespatterson729
2 жыл бұрын
@@rolandsgarage8640 prob a dumb question but im racking my brain , if it is poping out carb and the marks are set up between the flywheel and piston is at top also , the head is at its marks also , how can i correct it ?? does that mean the head is at the intake position ???
@rolandsgarage8640
2 жыл бұрын
Your camshaft is in the wrong position.
@b_wilk982 жыл бұрын
Has the Niche top end kit held up okay?
@rolandsgarage8640
2 жыл бұрын
Yessir, so far so good. No complaints at all.
@missypeppers31932 жыл бұрын
What will cause too much gap on the rocker arm
@rolandsgarage8640
2 жыл бұрын
They valves need to be adjusted. If it'd not covered in this video it will be in part 3
@missypeppers3193
2 жыл бұрын
I brought it to top dead center and it had a quarter inch gap
@rolandsgarage8640
2 жыл бұрын
@@missypeppers3193 you need to tighten them up then
Пікірлер: 18
Thanks for the help! BTW The kid is hilarious :)
Good job letting your little one help. I miss those days with my son. He is all grown up and working on helicopters in the Marine corps now.
Nice video got the timing right the first time on my 01
@rolandsgarage8640
Жыл бұрын
Good deal I could help.
You got a young Mechanic there...~Listen ~how he says My Turn that's it ,, he is serious,,
@rolandsgarage8640
2 жыл бұрын
Yes sir. I've told my wife that he will be my gear head
hey, I just got my 2003 Kodiak back together after rebuild. It runs great but there is still a loud clicking in the head. I set the valve clearances. any idea what it could be?
@rolandsgarage8640
3 жыл бұрын
It's probably the valves. Make sure you get the motor warm and put it on top dead center and adjust them again
after finding top dead center and setting up the timeing chain on marks flywheel and top end on mark . when trying to crank it , pops or back fires out the intake ?? am i 180 out ?
@rolandsgarage8640
2 жыл бұрын
Yea it pops through the carb your 180 out
@jamespatterson729
2 жыл бұрын
@@rolandsgarage8640 prob a dumb question but im racking my brain , if it is poping out carb and the marks are set up between the flywheel and piston is at top also , the head is at its marks also , how can i correct it ?? does that mean the head is at the intake position ???
@rolandsgarage8640
2 жыл бұрын
Your camshaft is in the wrong position.
Has the Niche top end kit held up okay?
@rolandsgarage8640
2 жыл бұрын
Yessir, so far so good. No complaints at all.
What will cause too much gap on the rocker arm
@rolandsgarage8640
2 жыл бұрын
They valves need to be adjusted. If it'd not covered in this video it will be in part 3
@missypeppers3193
2 жыл бұрын
I brought it to top dead center and it had a quarter inch gap
@rolandsgarage8640
2 жыл бұрын
@@missypeppers3193 you need to tighten them up then