With this technique you will do incredible work!
Тәжірибелік нұсқаулар және стиль
#lathe #tricks #washers #copper gasket #becreative #amazing
Hi guys, after many requests I decided to make this video....
Many people have difficulty turning parts with small pliers, so I hope you enjoy this video!
I want to remind you to always pay maximum attention and use adequate protection!
Even if it's a small gesture for you, every subscribe and like is important to the channel, so if you like the video, subscribe and like the channel...
Пікірлер: 65
Great idea! Simple, inexpensive, quick and works very well.
That was beautifully done and such an incredibly useful technique
AWESOME!, GOOD IDEA. THANKS.
That's good 👍 👍 👍
Fantastico.... sempre cose interessanti nel tuo canale
Amazing video
Bravo Türkiye den selamlar 🎉
Molto interessante bravo
Mantap bos.👍👍👍
Вот именно для этой цели я сделал маленькую проточку на кончиках кулачков. И теперь любая шайба толщиной свыше миллиметра легко зажимается прямо в кулачки.
Great idea, I shall store that up for future use.
Excellente idée. Je suis abonné à la chaîne et j'apprécie beaucoup. Merci 👍👍👍👍👍
Уровень ПТУ 😅😅😅😅😅
Magico! 👍👍👍👍👍👍😎😎💚💚🤗🤗
Very nice work.
Thank you for sharing this great technique.
Thank you so much sir for this new idia
You are doing unique work
تحياتى لك.. افكار ممتازه ومحتوى القناه مفيد
😀 tres tres bonne idees merci
Sehr sehr gute Idee. Vielen herzlichen Dank. Mfg.Lothar aus Haburg
elegance is in its simplicity.
Bravo!
Профессионалы так не делают, для этого существуют сырые кулачки с выточками... Но для гаражных хобистов пойдёт!
@user-cr6ml2xx8m
3 ай бұрын
У профессионалов два, три,четыре десятка комплектов кулачков (пропорционально стажу работы) под различные операции, гаражные хоббиты могут только мечтать о таком изобилии .
Laudetur Iesus Christus 👍👍👍 Deo gratias 👍👍👍
Making a small grooved adhesive plate works really good too with super glue, but I like this idea even better because you can keep the nice surface appearance without worrying about the heat turning it while removing...
You know the weirdest thing about watching these videos and knowing what everything feels like in your head.😂
Awesome technique. How to made a ring from Teflon with a thickness of 1mm and a diameter of 35mm, dephth - 5mm.
Es un antiguo recurso, usado por torneros para fabricar golillas (washers), también se le conoce como "camisa partida" (clamp). Generalmente se fabrica de bronce, material que es más "blando" y rápido para tornear.
And if you use the version with a shoulder against the chuck it gives you a repeatable reference for multiples.
Gracias ahora si me dejaste anonadado lo pondré en práctica 👍
👍👍👍
Ciao, sempre ottimi video! è un pò di tempo che ti seguo, hai anche una pagina fb e/o instagram?
@newtech5042
6 ай бұрын
Ciao, ti ringrazio... Al momento ho solo il canale youtube, comunque non escludo la possibilità di creare qualche pagina su altre piattaforme!
Метод рабочий! Но также для этого можно использовать токарный патрон меньше и сделать на нем микро выточки в кулачках
@user-vt2ng3dh6e
6 ай бұрын
смять шайбу можно, приходится осторожничать , а в оправе она плотнее сидит, не пережмёшь, особенно медяшки
An elegant solution , however just superglue the washer to the ends of the jaws ( it helps if the jaws are clamping something) , the washer doesn’t as a rule need to be concentric , hold it in place for a few moments with something in the tailstock , good enough for rock and roll .
🎉💪💪💪👏👏👏
👍👍👍❤
This is what soft jaws are for and do. A lot of these 'simple hacks' are unnessesary with a set of soft jaws used correctly
As a time served machinist I must tell you that you are only half right. what you missed is that you need to mark your fixture at number 1 chuck jaw so that you can put your fixture back in the chuck in the same place that you machined it every time to keep concentricity.
@newtech5042
6 ай бұрын
Hi, you're right! However, this is just an example, so I didn't want to waste too much time with the details... In any case, I thank you for the comment which may be useful for users.
Guarda che esistono i morsetti teneri, per fare queste cose. Comunque anche il tuo metodo e' valido, anche se molto macchinoso.
@newtech5042
6 ай бұрын
Ciao, hai ragione... Ma cerca di immedesimarti nel hobbista che vuole ribassare una singola rondella, pensi davvero che comprerà un set di morsetti teneri per quel lavoro???
That's very good. I wonder how to make a .002in washer/spacer
@mikebowling3228
6 ай бұрын
I could tell you how, you need to make several out of shim stock, finish the ID while holding on the OD then do not unclamp and put a bolt through the ID to hold while you remove the OD clamp or bolts then finish the OD
Would you call this a split collet ?
Non facevi più subito a fare la rondella?
so simple, i feel stupid
Would have liked to finish video, but couldn’t because of the irritating music😢
I guess you mean facing off!
try making them out of steel.
А что такое-опустить шайбу?
@user-cr6ml2xx8m
3 ай бұрын
Возможно уменьшить высоту ( толщину) шайбы?
это если их 100 штук надо. из за одной не будешь делать
How do you "lower" washers? Wrong word.
@newtech5042
6 ай бұрын
Hi, sorry for my bad English, what is the right word?
Древний способ ! Старо как мир !!!
@user-cr6ml2xx8m
3 ай бұрын
Уважаемый! Не все такие древние как Вы! Молодые начинающие "наркоманы"металлообработки имеют право знать и древние способы камлания с металлом.😊
The waggling finger is insulting and annoying, stop doing it.
@scorpion2nz
6 ай бұрын
Don’t like it. Don’t watch
What a waste of my time..
Se for muitas arruelas de diametros diferente aja matérial.
Primero aprende a hablar, girar????