Luis, I want to thank you for these sets of videos. I’ve watched all of them and because of your unselfishness by giving to us your most precious asset - time - sharing your knowledge; has saved me thousands of dollars. Today I replaced one set of rollers and the sliding door that was installed in the 1960’s and now works like new for only 20$. I have three more doors to do now. Thanks again!!!

This did the trick for me. Saved me the cost of new patio doors. Thank you.

A million thank yous. I had the wheel on the bottom break on me. I caught your video and hit Home Depot. I fixed it in about an hour thanks to your video.

All this time, I thought we needed a new door. Amazing!! Thank you!

Oh, forgot to watch part 1, forget my question on part 3 ;) Thanks brother, great video!

HAHAHAHA "God forbid you try to open it before you eat breakfast"!! That's the damn truth- I about threw a hammer through mine. THanks for the video man

thank you. big help

I know this video was posted a few years ago but I need your help and I figured I would reach out. I appreciate all you videos. As a single mom I do all my own repairs and you have helped extremely. I believe we have super similar sliding doors. I am struggling to get the screws out to move the frame up to remove my broken rollers. It is extremely rusty and partially stripped. I have used my impact gun and a hand screw driver but nothing. Any suggestions? I was thinking to just break the head off with something sharp and a hammer but I don’t want to break anything and I still wouldn’t know how to remove the other half stuck in the door. Can you help?

Helpful . Even though mine late 70s frames on west coast of Canada different. But assembly access same. Thanks

Have you replaced the top guides/stabilizers? If so, where did you get them from?

Can you please tell me how to remove the window sliding panel out of the frame? The only screws I found were to remove the whole frame from the Concrete wall

My patio door had a different design, the side bolt was also for adjusting the roller (and door) height, and should actually not be removed. Instead I had to split open the frame around the glass, which exposed a screw above the roller mechanism, to release it

Great video! What's the part number if you remember?

I probably have to get that track repair thing 😝. The end of my slider is enclosed on the bottom...not sure how to get to rollers

Most people are going to want to know how you got the door off the track......

Exactly what I need to do with mine which are era 1960. In fact I may have the identical door as yours.

You’re doing it the hard way. No need to take out all the screws. Just the bottom two. Then tap the bottom rail off. I’m a glazer with 13 years experience.

@deborahdandrea748

6 жыл бұрын

Ahsby Chavez ok so how to quickly .

@MediaLevel5

6 жыл бұрын

You are so correct. I just removed the screws that hold the rollers in place, tapped them toward the center with my long skinny screwdriver and pried them out. Home Depot had the same size wheel, so I did the swap and slid them back back in. Took 5 or six minutes, much easier!

@marcelosmith8359

5 жыл бұрын

Have the same door; having a hard time removing the door out because the wheel adjusting screw is stuck!! any idea on how to remove that screw if its stuck?

@diyfellow1627

5 жыл бұрын

Marcelo Smith Hmmm that's a bummer. You probably need 3 people. One on each side of door lifting the door up and another person on the bottom with a flat head screwdriver trying to pry the door away from the tracks with out damaging the tracks. Hope this helps.

@tamarakennedy4976

4 жыл бұрын

@@marcelosmith8359 you can get a spray called liquid wrench spray ut down at as many angles as u can...giver e minute n take a good screwdriver n unscrew her...oh and i found sometimes if its real bad from yrs i will give it a cple of taps with my mallot whilst spraying liquid wrench sometimes just that teeny bittle do da trick !!! Sorry just spent time with my family from narlins....aka new orleans!

Hey, I know it's an old vid was this door the dual pane design with the gas in between?

Louis, great videos.I especially liked the idea of 3 videos that automatically jumped to the next video. After completing the project, do you think it is possible to remove and replace the bracket hardware and wheel without repositioning the side rail? Just curious. Also the replacement rail is great touch!. Before I order the track cover, has the door continued to work as well as if did when the track cover was initially installed ? Curious how the cover has held up with use. Thank you FYI, I am a Coral Springs neighbor.

@diyfellow1627

5 жыл бұрын

Tom Ferguson Thanks for the positive comments! As far as the track cover it has held up great! Definitely recommend it if your track is looking shady. The door is still smooth as silk. 👌🏽 Now replacing hardware and wheel assembly with out repositioning the side rails not sure. I will be doing my other set of doors soon and I will sure try. Sounds like it's worth a shot! Let me know how it turns out for you. Thanks

awesome macaw

Also dry spray silicone is much better to lube wheels and slide like brand new

@diyfellow1627

4 жыл бұрын

Hey thanks a lot John Gill. I will definitely try that in the future.

Hello there, my sliding glass door is missing the handle, do you think you can make a video removing the door handle and giving us the part number and if you can please measure between the holes and tell us the spacing and any other measurement you can think of, so I can get a replacement or something close to it.. any help will be appreciated, thanks in advance.

HOPEFULLY after the end of the video ill show you the after. you had doubt about fixing it lol.

What screw size would you say that is. The Frame of my door is falling apart Thanks

Thanks. Very usefull. Where did you bought the long pieces to place on the tracks? I happen to have the same doors.

@diyfellow1627

5 жыл бұрын

Jackye Ferreira Amazon was the easiest place for me. Thanks!

@manasiyaabrar9539

5 жыл бұрын

Nice

And how did you get the door out of the frame?

Where did u get the part ? What's the part #

The channel my door runs in has dents in it and the door bounces when opened. Looks like I’m gonna have to replace it.☹️

Is there a trick to taking the door out of the tracks ? I have a similar door but i cant get it to clear the tracks

@diyfellow1627

6 жыл бұрын

There is usually a screw on the bottom. Stick a phillips head screw driver in there and rotate until the wheels go up into the door. That should give you the clearance to lift the door up and out. Thanks

@aldomania

6 жыл бұрын

Thanks man

Are the doors backwards? I have similar doors and bought a screen door for it but I have to place the screen door on the inside of the house because of how the doors are placed. It's very awkward and doesn't work. I've rented places where the doors are opposite of yours (the sliding one is on the inside of the house and the other one is on the outer side. I hope you understand what I'm trying to say😁) please tell me that this isn't the correct placement that the doors belong. Can the track be switched around to fit the placement that I desire so that I may utilize the screen door?

@Shyblues

5 жыл бұрын

Queen D I’m with you on this one & I hope he (or someone else) answers you, because I have the same problem where I live! All the sliding doors are backwards. 😯

You left out the hardest part; getting the door out of the track

@austinbutler1291

4 жыл бұрын

Lol you should be able to lift up on the door, lift it straight up and you should be able to pull the bottom of the door out of track.

@desertrat75

3 жыл бұрын

@@austinbutler1291 Nope.

@austinbutler1291

3 жыл бұрын

@@desertrat75 can you look on top of the slider and see if there is enough room for the door to even go up

@thedarkgift4442

3 жыл бұрын

for me the hardest part is getting the right parts to fix anything

@desertrat75

3 жыл бұрын

@@austinbutler1291 There's maybe 1/4". I found someone with a similar door on a google search about the same thing. He ended up breaking the glass trying to free the stationary door. I think the only way that door's coming out is toward the outside.

Where can you find track ?

@diyfellow1627

5 жыл бұрын

Check out Amazon. Easiest place to order it. Thanks!

What website did you use? I have a sliding door that is very similar

@CarlosVilla-qn9ds

7 ай бұрын

Some people are genius. Had you worked for a window company before

As soon as i spotted the macaw i was off track...

My door is twice the size of your and made back in 1960's?

I like to see how removing from his place the door its self...

@calartian85

5 жыл бұрын

Ayk Bayanduryan lift the door into the top of the frame. Swing the bottom of the door out of the frame first. Just like a sliding vinyl window frame.

@babinm

Жыл бұрын

@@calartian85 why not show this with a big slider people want to see the technique. It’s a large percent of the work.

Yes - so magically the door appears on a table. My door's stuck, and I can't take it out.

@diyfellow1627

Жыл бұрын

So mine was not hard to take out at all. You should be able to grab it by the sides, push up and then tilt the bottom down. That is how I did mine. If that doesn't work, on the bottom of the door there should be a place to put in a screw driver. That is where you should be able to adjust the height of rollers, I would adjust the rollers so it would give you more room to lift and tilt the bottom out. Hope that makes sense. ALSO you might have to have another person to help with the door, depending on the weight of the door!

You didn't have to order anything. Just buy a pair of 1' & a quarter loose rollers and replace rollers in existing roller housing. And , never use track caps. Always replace entire bottom track......you can order from a sliding door wholesale joint like I do almost every week for work. You will have to order a new track, or a bead cap...

@diyfellow1627

5 жыл бұрын

Hey Michael thanks for all of your comments. I appreciate them. Hey i have an idea. Since you do this almost every week for work, why don't you make a video and show us all how to do it. It would be much appreciated. Thanks!!!

@Shyblues

5 жыл бұрын

michael chilner Hi ! Yes please make a video of the way you complete the task ! The more we know the better 👍🏼

My problem with this is, I can’t find the parts

Why do you call PB Blaster, JB Weld?????

@diyfellow1627

4 жыл бұрын

Yea it's been brought up all ready lol

I have $1k that says you won't drive up to North Myrtle Beach and fix mine this week.

I'm pretty sure I have that same door 😂

@Bigshoots86

4 жыл бұрын

Pretty sure it's the ador/ hi lite 1200

Dude you called pb blaster jb weld dont put jb weld on there it definitely will not roll lol

I hope the Macaws have more room than that small cage. They need to be inside in their own room.

almost 100% way to make sure you have to buy a new window

This video could have started at 6:44 and ended at 7:00

Seriously you couldn't just do that in one video.

The guy just talks too much.

@diyfellow1627

4 жыл бұрын

Lol first time anyone has ever said that about me. Thanks I hoped it helped you in some sort of way!

If you are going to do how to videos you should at least get the names of your products you are using correct. PB blaster is not JB weld and it’s not WD-40 either totally different products totally different brands.

@diyfellow1627

Жыл бұрын

Thanks for taking out the time to comment!

Talks too much, and he didn't even showed how to remove the doors out of the track. Not a good presentation, sorry

@diyfellow1627

Жыл бұрын

Thanks for taking out the time to comment! Good luck to you!

Three minutes of babbling before we get in to actually fixing anything, then he skips taking the door off. Worthless.

@diyfellow1627

6 ай бұрын

Thank you for taking out the time to comment! Have a great one!