Have you had any heating issues with the PWM? How exactly do you have the fish finder connected? Is it directly to the battery with battery clamp?

@GoesTo11

3 жыл бұрын

Hi Jason...thanks for watching and commenting. I have not had any issues yet but I am making a modification to the controller box to prevent any overheating that may happen, especially on hot weather days. I ordered 2 small fans for graphic cards that are rated for 12v. I will put one on opposing sides of the box, utilizing the already existing holes that are capped on the box. The one fan will be drawing air into the box, the opposing fan will be flipped to draw air out of the box. Here are the links to the fans: amzn.to/3ajBipa (Canadian Orders) amzn.to/3ebUd6L (U.S. Orders) Regarding the Fish Finder, I always bring a small 12v battery for it and I get several hours of use from it. This helps extend the trolling time I get out of my main battery. If I am out there long enough to drain the small battery, I just clip the fish finder onto the main battery for a little extra time on the water. You can use alligator clips on the fish finder to make it easy to swap power supply. Here is something similar to the smaller battery I was mentioning: amzn.to/3ttKijn (Canadian Orders) amzn.to/3tvaTfT (U.S. Orders) I hope this information helps. Cheers, Rick

I will also add an on/ off quick switch to mine like I did on my canoe rig. When you are fishing down a bank & need to make small corections it is easier to just bump the switch on & off. That way you can leave the power at the same speed instead of turning it all the way down then back up.

@GoesTo11

Жыл бұрын

That is a great idea!

Hello, I wanted to say thank u for the great ideas, I have applied them all to our pontoons. Thought I would share an issue I had with the controller. I have 3 of them, all of them only reverse worked. Also they would get hot quickly. I had an electrical engineering at work help me out. He mentioned that any of these with a circuit board will fail quickly. He suggested the "HIMA dc speed controller, brush motor driver controls module DC 9v-60v 12v 24v 36v48v 60v motor pulse width modulator regulator 20a 1200w PWM monitor dimmer governor with switch and knob" Available on Amazon for $16. I tried the bungee for the steering and they were ok with small movements. After hours on the water they didn't work that good, but I will be changing these also. I will repost on how the new controller works out. Again thanks for the video and all the pointers to make these pontoons much nicer for fishing. Regards, Pinstriper

@GoesTo11

3 жыл бұрын

Hey Jeff, thank you for the great feedback! I may order one of those controllers as a backup. Since I made the video, I added a couple small fans to my box for airflow. I'll be trying them out next week to see how it does for temp. I used Paracord for the steering, it is more reactive than a bungee. I look forward to hearing how things are working out for you with it all and thank you again for your support, I really appreciate it!! Tight lines bro! Cheers, Rick

if you haven't found out by now... that metal clamp on your downrigger will damage your cable... use two cable ties... loop one as a cable guide and use the other to secure the loop to the downrigger rod inline with the depth gauge... it will be less abrasive.

@GoesTo11

2 жыл бұрын

Great recommendation T.C., thank you! I will look into giving that a try. I appreciate your watching and commenting. Cheers, Rick 😎 👍 🎣

@Manuel_Z_Kayaks

24 күн бұрын

Should have used a small pulley

Cool dude. I have the XT

@GoesTo11

3 ай бұрын

Only major difference is my seat swivels and you can buy one of those swivel plates at Bass Pro cheap! Have fun out there!

How many of the Attwood Trolling Motor Quick Connectors do you need? Thanks very cool setup!

Great video but where do you keep your rods? How many can you fit on there?

Did you Drill new mounting holes for the transom?

Awesome mods to XTS Rick!! Very well done!!

@GoesTo11

4 жыл бұрын

Thanks JB, I can't wait to get it in the water and chase some fins!!

Does having the battery and trolling motor in the back add too much weight to rear of boat?

@GoesTo11

3 ай бұрын

I'm a pretty big guy (6'2", 240lbs) and with all my gear on board it still rides quite level. I now have a front floor board on it and can move some weight up front.

Absolute BEAST.... Would love to see someone fab up a sun canopy on KZread for the one I’m purchasing today....

@GoesTo11

2 жыл бұрын

Thank you Iver...it is a fun rig!! I am thinking about designing a Bimini top for it. If I do, there'll be a video on it, so make sure you Subscribe to the channel! Good luck on yours and let us know what tweaks you do! Cheers, Rick 😎👍🎣

@ivermectin3191

2 жыл бұрын

Man are these fun…Been a great month for trout dinner…

nice Vid Mate

@GoesTo11

3 жыл бұрын

Cheers Mick, that pontoon boat turned out great! Thanks for watching & commenting M8!

I just purchased a used Classic Accessories Colorado pontoon boat in excellent condition. Now starts the process of adding the accessories to replicate your seat steering and motor controller. Any chance you could show how you wired everything up inside the waterproof control box? Thank you.

@GoesTo11

2 жыл бұрын

Hi Mike, that's great - you'll love it! Hit me up on Instagram in a private message and I'll send you some pics tomorrow. @goesto11media

Your thoughts on installing a weed/grass guard on the trolling motor? Seems it would help prevent any possible blade strikes cutting the pontoon material. Great video!

@GoesTo11

3 жыл бұрын

Hi Bill, thank you for watching and commenting - I appreciate your support and am glad you enjoyed the video! You can attach a grass guard but I haven't experienced the need for it. I do sometimes go through some shallows and have clipped the bottom of the shore but the plastic blades are pretty durable and are inexpensive to replace if needed. The prop itself does not come close to the pontoons, since it is mounted mid point of the frame, so there is no concern about that. I am excited to get back onto the water this Spring! I hope you have subscribed to the channel, lots of great content coming! Love to see your pontoon build if you do one. Tight lines my friend!!

What battery do you have..and how longs it last???

I love your chair directional method. I have a replacement shoulder which gives me limitations on shoulder movement. Thanks

@GoesTo11

2 жыл бұрын

Thanks John, it works great! I have a bad back and a shoulder issue too which made this a game changer! Let me know how it works for you. Cheers, Rick 😎👍🎣

@johntaglia9378

2 жыл бұрын

Will do thanks again

Materiais que utilizou do Amazon se faz favor obrigada

What mount did you use for the fish finder? Any link for that...

@GoesTo11

3 ай бұрын

Scotty Mount like this one is what I use www.amazon.ca/Scotty-Inc-0368-Universal-Sounder/dp/B00FPQZ95K/ref=asc_df_B00FPQZ95K/?tag=googleshopc0c-20&linkCode=df0&hvadid=292950491230&hvpos=&hvnetw=g&hvrand=7303979117692067950&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9001519&hvtargid=pla-458958847114&psc=1&mcid=bca46e19f2ab34f1aaa69873a4618b71

Curious as to how much total weight it can hold. I’m 5’9 220lbs. Would I be comfortable you think? Excellent video.

@GoesTo11

2 жыл бұрын

Thanks bro, I appreciate your watching and commenting! I'm just over 6'2" and weigh 240lbs and have not had any issues. The boat is rated for 400lbs, so no worries there. The recent adjustment I did is I bought a taller mast for the seat so I sit higher off the ground. I throw both in my vehicle and decide once at the water how I want to ride in the boat. It's an easy change out and you can swap back to the low profile mast if you want. I hope this helps and I'd appreciate you Subscribing to the channel if you haven't already. Let me know if you buy one, I think you'd love it! Cheers, Rick 😎👍🎣

Liked. Thanks. May I ask if you have tested the maximum speed on still water, and how many lbs thrust is your trolling motor? Well done. Thanks.

@GoesTo11

3 жыл бұрын

Awesome, thank you! I haven't tested for max speed but will try in the next couple of weeks when I can get out on a lake. I'm using a 30lb thrust. The boat rating says it's the biggest size it should use. I did test out my 55lb thrust and it had it moving pretty quick and on full caused weight to distribute towards the back and lifted the front of the pontoons up...not a great situation. I hope you'll subscribe to the channel, lot's of cool things coming!

Does it turn in the direction of the downrigger?

@GoesTo11

Жыл бұрын

Hi Christopher, I can swivel the chair to direct the boat in whatever direction needed. If you are asking whether there is sufficient drag from the rigger to pull the boat, I don't use a heavy ball to cause that kind of drag & also don't typically go super deep. I hope I answered your question. Please subscribe to the channel, I need the support! Wishing you a great 2023! Cheers, Rick

How long does your battery last in time on avg?

@GoesTo11

3 ай бұрын

I would safely get 4-6 hours out of it when at low rpm.

Nice video! How long does the battery last?

@GoesTo11

2 жыл бұрын

Thank you for watching and commenting DJ! Battery life depends upon how fast I troll and if fighting wind, etc. I have a 24 Series and use a 33 pound thrust and can make it last the day if I'm cautious about opening the throttle lol. Hope this helps. I would appreciate you Subscribing to the channel if you haven't already! Cheers, Rick 😎 👍 🎣

how do you store and transport that thing....researching on getting one of these or cumberland or 7bass...storage space is an issue for me. Any input would help . Thanks

@GoesTo11

3 жыл бұрын

Hi Adam...they're super easy for transport! I have a MINI Cooper and it fits in the back no problem. I leave pontoons attached to each side frame (but deflated obviously). They can stack on top of each other or side by side and the middle frame with seat fits easily. The motor, battery, etc is all removable and easily stowed. For storage at home I hang the pontoons from roof of garage 3/4 inflated. You can find all you need to buy using the links in the video description for this setup, or visit our store www.fishingandoutdoors.ca for all your outdoor needs. Please subscribe to our channel, we have some great giveaways coming up! Cheers, Rick :)

Kudos to you and Glen for a job well done. Simplicity makes for a relaxed fishing adventure. Now some questions for you. I have an Endura 40# motor that has an 8 gauge power cable attached, and those Atwater quick connects are 10 gauge. Have you run into any issues since you’ve stepped down to a smaller wire? Also...what size pipe hanger did you mount on your motor steering system? Also was there any reason you bought that switch, when the motor speed controller came with one? Thanks a heap for your great info! Oh yah...I’m in the Seattle area, and I’m guessing you’re above me on the other side of the border. Possibly B.C.? Mike

@GoesTo11

3 жыл бұрын

Hey there, thank you for watching and commenting - we appreciate your support! My MK is the 30# and I have not noticed any issues and Glen is a Millwright and would not have done it if there would be problems. I highly doubt you would have issues with the 40# and frankly, the draw is not a crazy load but I will message him tomorrow for his thoughts and get back to you. I also need to see if I can find my receipt for the pipe hangers, I had a heck of a time finding them online and went to a local plumbing company to buy them. The vertical shaft of the motor is not very large, I just cannot remember the exact O/D of it. The setup makes for a far more pleasant day on the water and makes it a lot easier to fight a fish! Yes, I am located just across the Border in Surrey, B.C. I love Seattle and have been there many times for day trips to guitar shops and the E.M.P.! Unfortunately, I don't think the Border will be opening any time soon. Hope you are staying safe and doing well my friend! I will let you know the answers to your questions tomorrow! Please subscribe to the channel, I would really appreciate it! Cheers, Rick

@sweetcakes3706

3 жыл бұрын

@@GoesTo11 Ha! I just knew we were neighbors. I appreciate your prompt reply. Yes, I don’t see a big issue with the wiring, but thought I’d ask if you were tripping the breaker or anything like that. Since the quick connect leads are short, they shouldn’t be an issue. I’ll probably just go with the Atwaters. Today I welded up a bracket to the center of my rear frame, so I could mount the motor in the middle. Now to find a swivel to attach to my chair! This is soooo gonna be worth it. Thanks again, Buddy. Cheers and stay safe!

@GoesTo11

3 жыл бұрын

@@sweetcakes3706 lol yup, just north of ya Bro! 🇨🇦🇺🇲 I just spoke to Glen and he said that the wires shouldn't be an issue but you should look at the Owner's Manual or contact the Company to be sure. We don't want to say "yeah, do it" and have your motor fry lol. Personally, I would go for it, but that is just what I would do (as I did on mine). I accepted the risk to my own equipment. The circuit breaker works great, though I've not tripped it. The area you'll want to watch is heat on the pentiometer. The box is enclosed to keep water out with no airflow. A larger motor may cause it to heat up, I am not sure. Let me know what you decide and how it turns out! Cheers, Rick 😎👍🎣

@GoesTo11

3 жыл бұрын

@@sweetcakes3706 yeah, the motor bracket in the middle is awesome! The swivel steering works like a charm. During this off season I bought a pedestal for the seat to try to sit up higher. I think it'll be very comfortable!

@sweetcakes3706

3 жыл бұрын

@@GoesTo11 Yah...I’ve thought of adding a 4” pedestal to my seat. Actually I’m thinking of replacing the whole seat with a new cushy one.

Very cool Rick heck of a fishing machine

@GoesTo11

4 жыл бұрын

Thank you Ernie! I am really happy with how it turned out!

That is a decked out toon! Do you have any pics of how you mounted the downrigger and pole holder there? I have a small downrigger and the best idea I've had so far is to just drill it into the standing platform lol do you have any videos of this on the water yet? Looks awesome!

@GoesTo11

4 жыл бұрын

Thanks! I will snap a pic and I just followed your Instagram page and messaged you. I will send you a pic of it there. We welded a piece of 3/8 metal onto two threaded 3/8 rods. It just drops into the front 2 oar lock holes and I use wing nuts and washers to secure it. Works great! I just completed the project the other day and hope to get on the water next week with it. I will film it and post once I get out fishing on it.

Where did you pick up the box for you pwm? I’ve been to a couple different Lowe’s and couldn’t find on like that . And did you have to modify the inside of the box or fit the unit, and help is much appreciated thanks

@cattrackersfishing1163

3 жыл бұрын

Never mind seen you list 🤙🏻🤙🏻

@GoesTo11

3 жыл бұрын

Hi there...I got it on Amazon and I put links to everything in the description. I've made a slight change by adding some small fans to draw air into the box for cooling. Feel free to ask any questions and thanks for watching and commenting. I hope you've subscribed to the channel. Cheers, Rick

What part and where will you purchase the 'voltage meter' for the battery indicating usage and remaining power?

@GoesTo11

3 жыл бұрын

Hi Martin...I just ordered this one and it works great! amzn.to/32DnTF1 Thanks for watching and commenting. I hope you've subscribed to the channel, lots of great Subscriber giveaways happening! Cheers, Rick

@martinshubin6828

3 жыл бұрын

@@GoesTo11 thank you so much for this video and all of your 'links' to the products. I have purchased all these great items so I can convert my pontoon boat to a customized one like yours. Thanks for the great ideas and product links!

@GoesTo11

3 жыл бұрын

@@martinshubin6828 Hi Martin, you're most welcome! Thank you for supporting the channel by watching, I really appreciate it! Feel free to follow us on Instagram @goesto11media and you're welcome to shoot me a direct message on there if you have any questions about the build and I can help you out. Take some pics/video as you build it for a fun video, I would love to see it! You will love the pontoon once done, it makes things so much easier. Just take your time with the pentiometer box, you can easily blow out the circuits if you wire it wrong. Cheers, Rick

Do you have a 30” or 36” shaft on your trolling motor?

@GoesTo11

3 жыл бұрын

Hi Milo, thank you for watching and commenting! It is a 30" shaft and this setup works great. I hope you'll subscribe to the channel, it really helps me out. Cheers, Rick

@milobloom6215

3 жыл бұрын

Done. I have a white river boat but looking at these as well. Looking for the links for the PWM set up. This is the best one I’ve seen.

@milobloom6215

3 жыл бұрын

Ordered a bunch of items although the PWM you link to is out of stock. Other brands that look identical. Did you use the variable switch that came with the PWM or did you find a waterproof option too? Also, do you have a riser on your seat? Do you find it difficult to row?

Thx so much for the product listing & links to your mods! I got stumped on the very 1st one I searched for - the speed controller - since I'm so ignorant with electrical anything :-( Amazon had plenty of listings for your exact verbage so I'm not sure exactly which one you used; I guess the manufacturer name would significantly narrow it down. I'd love to model after your setup if I can :-)

@GoesTo11

3 жыл бұрын

Hi Billy, thank you for watching and commenting - I am really happy to hear that my video helped you out! I will gladly pass along the exact names of stuff for you if the Amazon links did not work. Please let me know which items you need assistance with and I will add more details for you right away. It is a super little set up and I now have my floorboard mod done and can film it in a couple of weeks, as I am moving this coming week. I hope you have subscribed to the channel, lots of great content coming and giveaways for Subscribers! Cheers, Rick

@BillyGirlardo

3 жыл бұрын

I only checked the link for the speed controller so far but the Amazon link that you have listed brings up a site saying :Page not found: from Amazon which is why I'm asking for the brand name at least cuz that might happen to the other links also

@GoesTo11

3 жыл бұрын

@@BillyGirlardo Hi Billy...thanks for bringing it to my attention. Sometimes Amazon Sellers run out of stock then a new link gets made. I just updated the link for you with a new one in the video description for the speed controller. The name is "Sydien 10V-55V 12V 24V 36V 48V 40A Stepless DC Motor Speed Controller with Forward-Brake-Reverse Switch,Ajustable Potentiometer &Digital Display" LOL...it is a long one! I hope this helps you out and feel free to message if you need anything else bro and I will do what I can to help you out! Cheers, Rick

@BillyGirlardo

3 жыл бұрын

Yeah I figured that was the problem with the link I see a picture of the item now thanks so much I'll go through the rest of them later my XTS will be here in a few days so this gives me a big head start thanks again

@GoesTo11

3 жыл бұрын

@@BillyGirlardo Cool, I subscribed to your channel and look forward to seeing a video of your XTS! You can hit me up anytime on Instagram @goesto11media too, I check it regularly for messages. Are you in the U.S. or Canada? Cheers, Rick

I would like to know how you mounted you hummingbird transducer on the unit.

@GoesTo11

3 жыл бұрын

Hi Steve...thank you for watching and commenting! I used the Scotty transducer mount and it works great!! You can find the list of supplies in the video description but if you have any questions, feel free to comment here and I will do my best to answer them for you. Here is the link for the transducer mount amzn.to/2W80nfJ I hope you'll subscribe to the channel, I really appreciate your support. Have a great day!! Cheers, Rick :)

@stevetiffin5646

3 жыл бұрын

@@GoesTo11 thanks very much for the info. Greatly appreciate. I did subscribe.

@stevetiffin5646

3 жыл бұрын

We’re did you guys get the mount for your hummingbird monitor that mounts onto the frame.

What type of scotty mounts did you use?

@nathanieleasonbign81970

3 жыл бұрын

Nevermind i red the description lol

@GoesTo11

3 жыл бұрын

Hi Nathaniel, thank you for watching and commenting! All of the items are listed in the video description. Here's the ones I used: Scotty #243-BK Square Rail Mount (I just drilled a hole through it and into tubing frame then used self tapping screws) amzn.to/2WnZSP5 I hope this helps you out! I'd really appreciate you subscribing to the channel, it helps me too! Cheers, Rick :)

Hey, is there somewhere I can contact you about the motor details? I recently picked up an XTS secondhand and I want to get more info on how you did it! I initially wanted to make these mods to a 36" 55 lbs Minn Kota, but the 30/30 is $100 and the 36/55 is $250, so a no brainer for warranty voiding purposes. One problem, doesn't the motor not go deep enough into the water though?

@GoesTo11

3 жыл бұрын

Hi David, message me over on Instagram @goesto11media and I can message with you

@davidmalkowski7850

3 жыл бұрын

@@GoesTo11 Nevermind, I shuttered my Twitter. Do you have Telegram?

@GoesTo11

3 жыл бұрын

@@davidmalkowski7850 no, but will give u details via email then.

@davidmalkowski7850

3 жыл бұрын

@@GoesTo11 Got it. Thanks!

How do I go by registering my one man pontoon boat, can someone help me please?

@GoesTo11

3 жыл бұрын

Registration requirements will vary depending upon where you are. If you are in Canada, visit this site: tc.canada.ca/en/marine-transportation/vessel-licensing-registration To the best of my knowledge, at least here in B.C., you only need to register if you're using a motor over 10hp. The pontoon I show in this video cannot have anything larger than a 30lb thrust electric, therefore it does not require registration. I hope this helps you out. Please subscribe to the channel, it helps me out! Cheers, Rick

How did you hook the fish finder?

@GoesTo11

3 жыл бұрын

Hi Yacine...thank you for watching and commenting. I used a Scotty Mount on the frame (here is the item: amzn.to/2WnZSP5​ ). I then used a Scotty Mount for the Fish Finder ( amzn.to/3dh5t1g ). It all works really well and I am super happy with the end result! I hope you will subscribe to the channel and feel free to ask any other questions about the pontoon setup. Cheers, Rick

@yacineb4508

3 жыл бұрын

Thank you 🙏 so much for the information!!!

KIND OF WONDERING IF ANYTHING WORKED... LOOKED ON YOUR CHANNEL AND FOUND NOTHING ABOUT IT'S USE ON THE WATER.

Bloody genius.

@GoesTo11

3 ай бұрын

Thanks!...getting her ready for the upcoming season! Best of luck to you out there :)

Shouldn't your battery be in a box?

@GoesTo11

Жыл бұрын

I actually got a box for it after I had filmed the video. The box secures the battery in place & works well.

YOU ARE SMART

@GoesTo11

2 жыл бұрын

Some days lol 😆 Thank you for watching and your nice comment. I hope you'll subscribe to the channel, more great stuff coming! Cheers, Rick

Looks like you could easily mount 3 of the new small LiPo4 batteries and still not weigh anymore than the 1 lead acid and get many hours of run time.

@GoesTo11

3 ай бұрын

True, but I would need a chunk of money to buy them lol. Those little batteries are crazy expensive but would sure be nice to have!