Thanks great job and service. Iam expecting the delivery of this unit on August 26,22.

What is the dimension of the carton? Also, thank you for taking the time to make this video...very helpful.

To test the hot/cold output if your tapes aren't marked in some way don't bother with the bucket just run the hot into the drain. I did the bucket thing then realized I could test the taps and the connections and run your hoses one at a time to the drain in essence testing the drain capacity as well.

Tank you for the video

should you use filters on the hoses?

How much water does the washer hold

What about the spliter ? What about the short hose ???

I’ve used my new Electrolux washer 427 a few times and it vibrated a lot. We pulled it out and found that the installer didn’t remove the yellow moving plugs or leave the replacements with us. How can I find replacements for the 7 holes? Thanks.

@Lifes_A_Beach

2 жыл бұрын

Hopefully you called Electrolux support. I suspect they would have been willing to send you some.

Why the drawer to the left of the stove?

@luedey7704

6 ай бұрын

My thoughts exactly. That's my dildo drawer. Stay outta there

I was hoping he would show the operation after he installed. I have a new washer and I'm not sure it is working correctly. There are three nozzles inside the washer for water and light. The nozzle on the right shoots a full stream of water. The nozzle to the left of the light nozzle just shoots a trickle. Is the left nozzle the cold and the right the hot or is the mix of hot and cold into the tub mixed in the full stream nozzle to the right of the light?

@coconutmonkey2823

Жыл бұрын

Those are the fill and rinse jets depending on what stage of the cycle it is on. Its made that way because it mixes the detergent before it hits the clothing. Thats one of the reasons its the top rated washer. Read the manual.

@windcheck.iah26r8

Жыл бұрын

@@coconutmonkey2823 I have read the manual. Please re-read my poorly written question above. Is the one on the left suppose to be a trickle compared to the full flow from the right jet?

@AsTheWheelsTurn

8 ай бұрын

yes it is supposed to be that way.@@windcheck.iah26r8

You didn’t put the plugs into the holes on the backside.

There is a problem with this video. In your video, you only hook up the washer to the cold water, and then you turn the valve on. Then, after the fact you mentioned that you did hook it up to the dryer already. But if someone is following your instructions, they will have water pouring out the other hose because it was not yet oft up to the dryer. And I have one question. Why do steam dryers not use the hot water? Why do they use cold water? Thank you.

In the video you never put the plugs back in the shipping holes?

En donde se encuentra el filtro atrapapelusa

Here’s one for you. The washer displays HO SE after the cycle. All connections are on correctly..I’m stumped

I bought the same washer, and on the first load start a big noise nonstop continue, I turned off, and even plug-out the eclectic power but the noise continued not to stop, a loud noise from the left side of the washer, do you know what's the cause of this noise which doesn't disconnect after power line even off?

@YhwhKhaiMostHigh

11 ай бұрын

Did you remove the 3 shipping bolts in the back?

@zackbrian8012

11 ай бұрын

Same with me.

@andrewbester4113

6 ай бұрын

Mine is also doing this. Sounds like the water pump is struggling

When you removed the shipping bolts you cut the video which would show how hard it is to remove the top bolt's retainer plug. In fact all those plugs were a pain to get out and on my machine, the one holding the plug, when removed a nut fell down inside the washer. Guess I will just leave it inside the machine because getting it out will be a major undertaking!

@AsTheWheelsTurn

8 ай бұрын

was not hard for me! maybe you should have just hired someone to do it , there was absolutely nothing difficult about this installation at all.

Why is mines shake so violent and jump when in cycle it spin so violently

@ronymathew6232

Жыл бұрын

Check if the shipping bolts are uninstalled or not. If they are removed then check if the machine is level or not. Ideally if you try to shake them they should not move much. If they shake easily means they need levelling. Hope that helps

Karens have entered the comments

so frustrated that this video showed everything except how to get the dryer hooked to the water supply?? seriously why?

@JohnDoe-mp1zk

2 жыл бұрын

because it probably sucks and is not worth it. I have one and a family member who has his own appliance store and has same dryer doesn't even use it

@hug0lle

Жыл бұрын

There's a super precise drawing of how to do it on the dryer when you buy it Can't be easier to do

Why have you all stolen most of your Electrolux videos from Electrolux’s portal? That is so unethical.

@tif321dc

7 ай бұрын

Where can I find the videos from Electrolux? Thanks

Irresponsible to the extreme, the demonstration does not place enough ‘beware’ over the fact that the fancy yellow mounts holding the various hose and electrical cables each have a three and a half inch 5/16 steel bolt attaching them to the inside of the drum area! Removing these bolts before operating the washer is extremely necessary! This was not mention whatsoever. Idiots.

@gladitsnotme

Жыл бұрын

3:53 he literally talks and shows the removal of the shipping bolts

@AsTheWheelsTurn

8 ай бұрын

that was one of the very first things he talks about....you must be pretty stupid if you just figured since he didnt make a huge deal about how important it was it must not be important....if the instructions say you need to remove something before use that should be all you need to know.....I would say a person would have to be an idiot to just assume it didnt matter because there wasn't some extreme warning given...

@AsTheWheelsTurn

8 ай бұрын

also....every one of the yellow retainers says clearly on it REMOVE BEFORE USE so how much more of a warning do you think you need> Id say you are "irresponsible to an extreme" if you need that much extra help on that