Without you today, it would have been a worse day. Thank you Homie. Straight to the point, I love it

Brother - Your video save me today - Spider gears got loose while rebuilding my Van rear end differential at home-Thank YOU!!

This is exactly the video i didnt know i needed

So glad this video was made going crazy trying to figure that out .

Thank you very much Illustrated Man! You saved my life.

Thanks. I needed to know that as I had lost the spider on one and did not know how to put it back in place.

Bro you saved my life just now. I had the right idea but not the right set up method

You made it look easy. Hope it works that way for me.

This look so easy I have 04 gmc yukon my spider gear is bad this shop said it will take 2 days and the labor will be $475 to put on after me seeing this video I'm not no mechanic but I think I can do this great video

Thanks, you showed me what I needed. Might talk a bit louder next video.

Thank you young man that was very very helpful !

Thanks for this video! It helped me out of a jam

Thanks!! Needed this!!

This was very helpful thanks a lot.

Thx. Good demonstration

Good job bro, great video 👍

Fought with a set of spider gears for like 2 hours trying to get them lined up perfectly should have watcht his video first

Awesome video

Nice video. Thanks much!

made it look easy!

Good video,you should really put some thread locker on the shaft bolt

I really love this video cool

Fuck gotta love u tube and people uploading these videos, tks

Where do all the washer go with the spider gears in the differential gear kit?

learning and will try it on my own save 2000

Does it matter if you mix those two spider gears like do you have to put the top gear back on top and bottom back on bottom

I get the just of the video. However, if you're going to teach someone how to install the used spider gears to it the right way. First. Look at the side gears teeth and find the side gear that mimics the ring gear, drive coast. The drive side will have more wear. Now install it on the passenger side and the one on the passenger side to the drive side. The pinion gears should be flipped 180 too. This will allow the pinion gears to drive on what was the coast side of the spider gears. Increasing the life of used spider gears.

@spelunkerd

3 жыл бұрын

Oh, so you are rotating the gears so long term wear is even, much like rotating tires to get longer life. Cool.

@66and72nova1

3 жыл бұрын

@@spelunkerd, Let's say you have a posi or open carry. Rotating the spider gears must be done exactly. Driver's side side gear to passenger side. Passenger side to Driver's side. Pinion gear closest to cross shaft bolt moved to opposite side farthest away. Farthest away spider gear moved closest to cross shaft pin bolt. This will allow cause the spider gears to drive now on the coast side instead of continuously driving on the drive side. Coast side of the gears will have less wear. If the spiders are extremely worn then best to replace them.

@richardspaulding5035

3 жыл бұрын

My dam truck is 40 years old, I am not worried about how much longer the gears will last will last LOL.

@66and72nova1

3 жыл бұрын

@@richardspaulding5035 Yep, that's why, Why people sell a used 12 bolt car or truck rearend they want 500.00 to 800.00 when all you have to start with is a bare housing. Everything else is worn out.

Does having the bearing caps removed make a difference? I can't get my spiders gears in place as I can't seem to get my side gears pushed in enough to allow the spider gears to sit lower on side gears.

@ruinedgti6511

Жыл бұрын

how did you end up getting this done, having the same issue

Great

I’m trying to get my center pin out but the ring gear doesn’t let it come out all the way.

Thank,s

What about the yellow springs?

How did the gears not fall out when you replace the splines

Sir how to order 8.6 gm spider gear set 10 bolts? I need for Chevrolet Silverado 1500 MY 2000 Thanks for the video

Thanks for video BUT I put my spider gears back in and all is tight. But when I turn the axle is there supposed to be a little play on the spider gears ?

@andrewgalvan5852

5 ай бұрын

Small amount

They are a pain in the ass without the proper tools when putting in however when you use a dissolve stitches to pull the spider gear in so it doesn’t fall out it makes thing a lot easier

♥️👍👍👍👍

Why would the spyder gear shaft break

Does the baring cap need to be removed before putting the spider gear in? Please help 😅

@shortchange26

7 ай бұрын

No. It does not. However, if you’ve rounded off the hex on your lock bolt you can’t get a ratchet with socket in there to remove it.

If i have my truck in jack stands and put it on drive only one rear tire spins is that normal ?

@gregl5677

5 жыл бұрын

Depends if its open or locker or lsd

@jmj_d5207

5 жыл бұрын

@@gregl5677 its an open differential

@jmj_d5207

5 жыл бұрын

@@gregl5677 its from a 2000 chevy silverado i guess code for it is a gt4 diff

@gregl5677

5 жыл бұрын

@@jmj_d5207 does it have a g80 code next to gt4? If not its fine its a open diff g80 code was fore posi trac. Unless the rearend had a locker put in it at some point.

@jmj_d5207

5 жыл бұрын

@@gregl5677 no no g80 just gt4

"Side gears" are actually called planetary gears. "Spider gears" are called sun gears.

you must know how to time the gears. this should take five minutes max. rotate the prop till the small pin bolt is centered between the main bearing caps. now simply drop a spider gear down from top and slap the other. hold the bottom one up and rotate the prop till the main pin holes will line up.

Man if I knew this I would never got myself in this mess

@MicroSoftner

4 жыл бұрын

Did ya fix the mess?

you forgot the washers on inside of the side gears

@MicroSoftner

4 жыл бұрын

I think I see em already on ?

there is two washer beside the two small gears, this way is difficult operate in a real truck

06:12 You didnt tight the spyder gear pin retainer at all.. Geeee..

Don't take your car axle to this dude

I call bullshit it's not that easy it just doesn't go in!