кто прошёл через восьмёрки-девятки с 41ми, не поняли смысл видео.

@Vasya242m

Жыл бұрын

на 41м молоток ваще не нужен))) колечки разжал и готово. ну бывает надо немного ударить))

I usually tap it a bit to center the lock ring then I hit the outer race with a brass hammer.

8:45 they completely destroyed the end of the axle with the puller. Pulled the ring groove totally off of the axle. Junk now.

@eldiablo1987

Жыл бұрын

Yes they ruined it.

@AbbasBinYounas

Жыл бұрын

Does it not have a circlip which can be removed using a dedicated tool? That way it could simply be pulled off after removing the clip??

@MegaMarclar

Жыл бұрын

@@AbbasBinYounas the clip is a simple hardened C clip. It can easily be removed with a pick or screwdriver, after being removed from the vehicle. You can see in this video where they completely destroyed the piece of the axle that holds that clip. The axle is now useless.

@AbbasBinYounas

Жыл бұрын

@@MegaMarclar thanks a lot... This is somewhere in my country, and here the mechanics believe that replacing CV joints is not a simple task requiring hand tools, but a machinist's job that requires specialized tools... I can almost guarantee you that once they were done with the CV joint, they would've welded the race in place, instead of using the clip. This is a common practice here, they ruin the shaft and then weld both sides of the CV joint in place...

@MegaMarclar

Жыл бұрын

@@AbbasBinYounas Yes it's actually extremely easy to get those out. Just a simple set of pry bars is more than sufficient. It just seems like a total lack of dedication on the so-called mechanic side. That c-clip holds the axle in so if it's not there the axle will actually pop out while you're driving

Иногда проще молотком через выколотку по внетренней обойме стукнуть, чем полчаса собирать съёмник, а потом полчаса его крутить, но выглядит красиво)

@mavugogeorges2041

2 жыл бұрын

Ok.merci

@Alexandrtru1973

2 жыл бұрын

Попробуй стукни на опеле или тойоте) при замене помогает только болгарка и зубило...

@user-dl9bp4rw2b

2 жыл бұрын

@@Alexandrtru1973 ну например, на Опель Зафира стучать практически не надо, там наружний ШРУС держит кольцо, которое раздвигается пассатижами для стопорных колец и ШРУС свободно выходит, на некоторых Тойотах сбивается нормально, а где не получается там болгарин и зубило помогут.

@Alexandrtru1973

2 жыл бұрын

@@user-dl9bp4rw2b на Зафире В так не получится.

@aleck.truxin

2 жыл бұрын

На акценте попробуй побей,хрен там,снимаешь привод,делаешь съёмник чуть др.чем на видео,и сосать палец,делал и обратный молоток и по барабану,болгарка в руки и огромное желание,вот так вот,крайний раз думаю ну все равно обратным молотком возьму,сделал ударов 150 сломал обратный молоток и выкинул из головы съёмник,если что сразу болгарка и время не тратить.вплоть до того идёт дело,что и распелив гранат пополам остаётся сама обойма с кольцом и они не снимаются,болгарка и зубила в путь.вот тебе и выколотку,это жесть а не гранаты,пробывал и подпиливать колечко без толку,все равно не снять,но посмотрев это видео понимаю что не только я мучаюсь с этим делом,надо попробывать такой толстый метал найти и сделать такой съёмник мощный.

Man there is only a circling holding it on, that bracket is a waste of time and energy for this task, grab it with your left hand and keep pressure, and give it one good hit with a brass or dead blow hammer., the outside of the spider has a taper that will squeeze the circlip closed, there is no force pulling this apart during operation, in fact that bracket will make things worse..

@thomasbor

2 жыл бұрын

rocket science....lol lol

If I’m not mistaken it’s just a snap ring holding it on!

@christophermarshall5765

2 жыл бұрын

That is all, though some cars you need a screwdriver to open the retaining ring, such as a Daewoo Cielo.

@peted5217

2 жыл бұрын

Ya, you're rite. Wonder why this careful way ? I just used lg brass hammer bak when axels we're repacked, rebooted. Then the dawn of replacement happened

@christophermarshall5765

2 жыл бұрын

@@peted5217 the reason why this is done carefully is to avoid breaking the end off the shaft (I've actually broken the end off a drive shaft before.).

@peted5217

2 жыл бұрын

@@christophermarshall5765 Had not herd bout snapping axle tip off, but I only Tech'd 45yrs. Never even have it any thot cause they're so tuf. Goes to show the old axcion bout ruining an Anvil probably Tru. Ye ol Brass Hammer always worked.

@peted5217

2 жыл бұрын

@@leiladaquil6587 Those are the Worst !

I will never take my impact guns, air compressor, cordless tools, breaker bars, air conditioning, indoor plumbing and electricity for granted again,...

Takes less than a minute to give it a hit with a dead blow hammer it pops off easily This was a waste of time and it looked like you damaged the bearing race with all that unnecessary pressure. You don’t even need to remove the shaft from the car Next time pull the boot off the cv side only fold it back and hit it! comes off no problem.

@artix4635

2 жыл бұрын

Eso es lo que estaba pensando, gracias por decirlo.

@enriquebauza749

2 жыл бұрын

Agree with you 100%.i call these guys rookies. I bet anything when ever everything is said and done.that axle would grawl and make noise from the extreme pressure given to that bearing........

@JavoCover

2 жыл бұрын

@@enriquebauza749 I have to disagree with that, my CV's are doing fine after 80.000 Km of doing delivery's and constantly going to the extreme angles of the steering. And I'm going to agree about the too high pressue as I use the same tool but gently tapping with a light hammer each time I turn my ratchet on it, I don't use near that ammount of force, is only a slight pull.

@bonkeydollocks1879

2 жыл бұрын

Some have a flat circlip that needs to be removed first, some have the rounded spring clip, hitting a flat circlip one won't let it come off

@alexandros1517

2 жыл бұрын

Ok.. In most cases it pops off with a hit. Have you ever tried Toyota?? Honda?? Hyundai??

Having done many a CV joint in my life that looked chuffing tight. Nice work. Have seen many a CV joint destroyed with hammering.

@groydstein7007

Жыл бұрын

me have also and have never

The pesky retaining clip disappeared as if by magic, and the splines slid off nicely. Now we have a bucket of of worn-out CV joint parts instead of just a worn-out axle shaft. A bent piece of welding rod should make a good replacement clip, and some fresh grease will have that joint working as smooth and quiet as factory reman. Gotta give these guys credit for working in the dirt with sticks and stones. I make most of my own special tooling too...

Использование съемника в Пакистане дает +1,4 МЛН просмотров!

I use only a hammer to unplug It 😁👍

@danpal2314

2 жыл бұрын

Me to

@bobthompson4918

2 жыл бұрын

Me too.

Yes a tap with a copper mallet does the trip, also rotating the shaft so the internal circlip drops

The butchery getting the clamps of the boots set the tone. If your gentle getting them off you can re-use them in a pinch.

Va bene bravi ma basta stringere il fermo con un po' di pazienza dare qualche battuta e uscirà comunque

He made a right carry on out a simple job, for a start a pair of snips to get the band off. We change outer CV on car with a puller tool similar to the one in the video and a cordless impact wrench in about 1/4. of the time

@joseruycastro8544

Жыл бұрын

amigo você está tirando ou colocando pelo oque você fez foi colocar

@mandeo10

Жыл бұрын

They have to use the bands again as they don't have many new ones. So they remove them carefully.

This is the wrong tool. They're basically removing it by putting stress in the bearing surfaces - similar to removing a bearing on a shaft by pulling from the outer race.

При таком способе всё усилие на сепаратор. А у него рабочая нагрузка тангенциальная. По касательной к диаметру. А тут осевая. Может потом и лопнуть.

Gostei da chave de tirar mocinete bastante prática sem precisar de dar as quela marretada ótimo trabalho 🚒🚒🚒 Brasil BR

Hi very useful...because not all cv.s come with a hammer hit

По началу думал огоо стока папараци кругом фоткают потом дошло вспышки сварки🤣🤣🤣🤣

Купил такой съемник-реально не снял ни одного шруса, натяг даёшь-якорь деформируется, шрус не снимается

@muhammedk470

2 жыл бұрын

Do u use a hammer?

@vladimirsvyatskii9040

2 жыл бұрын

@@muhammedk470 да молоток, а иногда на тойотах надо распиливать сепаратор-извлекать шарики по однному, затем распиливать внутренюю обойму

@user-iu4kh6em9g

2 жыл бұрын

@@vladimirsvyatskii9040 с Тойотой ска только так 😉

@user-de2qj7ec6d

2 жыл бұрын

@@muhammedk470 где вы на приводе якорь увидели? Или вы на съемнике увидели якорь?

That's a great tool makes the job looks so much easier

Muito bom Campina

یااللہ ہمیں بھی مدینے کی افطاری نصیب فرما۔۔

I have personal experience like this too. My civic outer cv joint will not come off with a dead blow hammer, I have to order online to get that special tool. With that tool it is still not easy, it was hard. I still have to use an impact wrench. After it came off, I inspect the c clip turn out it was a round c clip different front the c clip on the inner cv joint. I don't know why it was so difficult. My inner had a little play but the outer was solid, so I replaced the inner. After cleaning the old grease and replacing with new grease, I reuse it. Feel good no vibration during acceleration and no sound when turning. That tool only cost me a round 20 USD+25 USD for inner cv joint , a new CV joint is 300 USD.

@eh6971

10 ай бұрын

Heat.

I thought he was being chased by the paparazzi on the red carpet with the flashes, until I realised it was welding being done off camera.. :D

That tool is pretty interesting

Thank you for get great idea sir i uplay that sir

Actually that could've been done with just a heavy duty hammer. Seems like a lot of preparation for such a simple project.

Bro it’s one hammer job

@amazingthingofficial2923

2 жыл бұрын

G ni😂😂😂😂😂

@phareztrinimand

2 жыл бұрын

You haven't worked on one that the hammer is useless an only damages the houses, for the this tool is a hit and miss, some axles don't have a big enough grove for the tool to grip on

The titles on these videos always crack me up😂

@MrSoarman

2 жыл бұрын

Everything is Amazing.........REALLY.?

Обратный молоток или просто молотком выбивал...на видео 9 минут,а по факту он долго мучился по ходу

@Pikulev_Evgeniy

2 жыл бұрын

Перед ним тоже слесарь тоже долго мучался. Край гранаты от молотка расплющен.

@mucio290

2 жыл бұрын

@@Pikulev_Evgeniy потому что бил не туда куда надо, по обойме внутренней бить нужно а не по корпусу, да и вообще, зачем ставить тогда пыльник назад да еще и хомуты затягивать

Good work 👍👍❤❤

Nice work ❤

Very nice video

I once dismantled such a joint. By bending the joint fully, I could pick out first one steel ball and then the rest and now the joint was in two parts. Believe I could then remove the spring lock ring ... and so on ...

good rotating damaged axel removal # 👍

This guy Is very talented with all hand tools I watch his videos . . Today's video he just got too much time waste . Amazing lathe skills by the way .

thank very much

I don't see the point of pressing it on when it comes off in the opposite direction

Non si è capito nulla. Il video è terminato????

С тойотой такой номер не прокатит, а если можно снять съёмником, то молотком по внутренней обойме тем более. С таким съёмником можно убить сепаратор.

@user-sr1ij9be9w

Жыл бұрын

Этот съемник не работает так, как на видео. Гайку надо крутить гайковертом, тогда от ударов и вибрации кольцо уйдёт в канавку и шрус сойдёт.

Show ...parabéns...objetivo... humildade... profissional... ao máximo dentro das suas condições.

Amazing video

Слишком много лишней работы.

в трипоиде была забита неправильная смазка (на молибдене) нужна на полемочевине.

Съёмник такой бесполезная штука. Не покупайте и не ведитесь. Если кольцо внутри закусило вы и съёмник сломаете и шлицы на валу повредите. Не пошла от молотка - берите болгарку выпиливайте обойму чтоб выпали шарики..

@user-du6sp4se5h

2 жыл бұрын

Был у меня случай когда молоток не справился , отвез в автосервис там за пару минут сняли сьемником

@dmitryderek4096

Жыл бұрын

А закусило его потому что стояло уже не заводское каленое, а сырье , да ещё кривое из дешёвого набора. И сбивали его не инерционником а кувалдой с перекосом

hello, do you sell the tool?

seams over complex most have a circlip you open with pilers and pull it off or if its a split ring you just whack it off with a rubber hammer

Hi my friend. Amazing video. Congratulations. I need a puller for me. Send to Venezuela please.

Assalomu Aleykum javob yoza olasizmi

I agree about the hammer but ha let’s agree he made a beautiful video

on mitsu you can pull out retaining spring and easy take appart

پاکستان میں ہنر کی قدر نہی ہے کمنٹ سیکشن میں صرف فارنرز کے تبصرے نظر آرہے ہیں۔ کہ وہ اپنے ہنر سے کتنی دلچسپی رکھتے ہیں۔ ہم پاکستانی سرمایہ دارانہ سوچ کے غلام بن کے رہ گے۔

Интересные вы люди, этот шрус уже кто-то снимал и побил молотком сам наружный колокол, так вы еще и тисками подмяли ось, которая бывает часто пустотелой. А сьемник - класный!

@Bandit69ply

2 жыл бұрын

I just went back and watched that part in the beginning at around 1:30. I saw the large mark on the outer bell area. So yeah, not a good video if you want to show anyone the "correct way" to remove a cv joint. Good eye brother!

@EtotMoy

2 жыл бұрын

Никогда не встречал такую полуось пустотелой, это ж не кардан.

@user-de2qj7ec6d

2 жыл бұрын

@@EtotMoy в вазах один привод цельный, другой пустотелый. Но съемник пуля

@EtotMoy

2 жыл бұрын

@@user-de2qj7ec6d хм, действительно кажется так, забыл. Хотя много раз менял на пятнашке.

@user-daqlle

2 жыл бұрын

@@EtotMoy смотри с 7:48 kzread.info/dash/bejne/oK6fr6WOc8Kbgqg.html и да, не только французские автопроизводители удивляют

check in 8:47 all are destroyd in point axle, is more easy take an an electric grinder and cut with calm .

You don’t need a puller for this. Dead blow hammer and a couple hits and it’s off. I actually can do it without a hammer by rotating it and popping each ball bearing out and then assemble by popping them in one at a time

@kernsy6715

2 жыл бұрын

I’ve done it over 100 times and never had a problem. I’ve done it to shafts that are broke where you can even use a vise and had it done in no time. There is a saying out there “You gotta be smarter than what your working with” and this video is not the case!!

Hmmm nice tool. I've always used a hammer..out within 5 seconds... But I hear some cv's are stubborn..good vid though. I hope your tool is not patented coz I might just "own" it..

ничего не понял, почему так сложно снимали гранату? я несколько раз менял гранату, все легко руками снималось, даже не снимая привода с машины или я тут что-то упустил в видео?

Amazingly

Definitely hard to remove this, tried countless hours on a honda. Dven the notorious honda pulley bolt was easier.

Esa herrmient es un gran estafa . Ya probamos dos y no desmont la junta homocinetica del eje lo invito a usarla en el eje de un toyota y haga un nuevo video

Самое скучное видео по съему шруса. Пол часа гайки наворачивать и отворачивать, а в конце ещё и вдвоем. Особенно зрелище как он хомуты снимал. Нервы не выдерживают.

Don't do this! You can broke ring holder on shaft!!! If joint not removed by hummer slashes, always cut of CV joint!!

@yunus5266

Жыл бұрын

You are correct. Most comments are from persons who do not understand why the shaft gets damaged. Using a heavy hammer fails. As demonstrated by this video, the shaft gets damaged by the use of the puller. Destroy the old joint,taking care not to damage the shaft. Repair the flare on the circlip groove before fitting a replacement clip. Fit a new CV joint.

After watching this video. I decided to replace the part myself instead of a mechanic.

Comes to you from 3rd World Productions, Inc.

Sir, can you help me make driveshaft head...

You can do this without removing the shaft from the car. He made hard work of the job.

Just don’t forget to wear your hajib ladies

@hardson7195

Жыл бұрын

☝️☝️☝️☝️☝️☝️ You’ve been selected text me above

За это время, можно уже снять и установить новый ШРУС, используя молоток.

Kiali bai

Excuse me.there is a circlip on the inside, remove it and joint slides off. Unless it's VW joint, hammer gets them off..

Yeah it's a puller. I use them all the time

Это можно и быстрее и проще сделать))))

Amazing

Toma tu like 👍👍👍👍👍👍😉😉😉😉😉

Испортил вал, стопорным кольцом срезал бортик.

que pérdida de tiempo,con solo un golpe seco salta la homocinetrica

Finely he used the hammer 😂😂😂

This reminds me of the saying " The poor man has poor ways".

Просто берешь 2 молотка, наставляешь один, бьешь другим. Все.

We dont have that here in the philippines mine was destroyed

Way longer process removing the joint lol.....Is only a snap ring retainer, ya remove boot out of the way.....1 good whack with a hammer BOOM it's off the shaft ( both joints same way ) lost count of how many CV joints I have repaired over the last 30 years lol have a big 3 lb brass hammer just for this....Not anymore I'm retired lol

На первом не получилось, хорошо что есть запасной.

Что пристали к людям. Они продемонстрировали как нанотехнологии внедряются в пакистанской жизнь. Ну и заодно перекусили вал привода.

unlike other method,here no heavy wacking!

Great job 👌

@amazingthingofficial2923

Жыл бұрын

Thanks

I think the real battle was deleted from the video 🤣

They damage the groove for the spring clip and makes the new cv hard to fit

A.O.A bhai aap ki shop kis jgah ha?

@amazingthingofficial2923

Жыл бұрын

G ap kon

If you drive around with it eventually it falls off that happened to me in high traffic boulavard

Todos tienen un seguro y con un destornillador manteniendo abierto el seguro con un martillo sale

Holy shit these guys made it look like a piece of cake this job..

Nice jig

Lol……now that’s a “ Shadetree” mechanic.

Just about everything was made overly difficult here. Already from removing the clamps. Lucky he didn't injure himself with that little, sharp screwdriver. If you have replacement clamps, you cut them off. If you haven't, you go careful, and reuse them, and never tell anyone about it. I don't actually think removing the axle from the vehicle was necessary here.

Love the chinglish titles

I read if boots broken for a while dirt, grit and gookies ruined joint.. Just buy a new clean one they are cheap insurance..Its really dusty there.. wounder how long it lasts?

Ausgegangen 👍👍👍👍

@amazingthingofficial2923

Жыл бұрын

Thanks