How did the gears not fall out when you replace the splines
@thetruthalways71362 ай бұрын
Without you today, it would have been a worse day. Thank you Homie. Straight to the point, I love it
@Oakcali4010 ай бұрын
They are a pain in the ass without the proper tools when putting in however when you use a dissolve stitches to pull the spider gear in so it doesn’t fall out it makes thing a lot easier
@texasscot6669 Жыл бұрын
Great
@tmancarguy Жыл бұрын
Does the baring cap need to be removed before putting the spider gear in? Please help 😅
@shortchange268 ай бұрын
No. It does not. However, if you’ve rounded off the hex on your lock bolt you can’t get a ratchet with socket in there to remove it.
@augoharris3437 Жыл бұрын
Thx. Good demonstration
@patrickhendrix699 Жыл бұрын
Thank,s
@brucefrightfull Жыл бұрын
you must know how to time the gears. this should take five minutes max. rotate the prop till the small pin bolt is centered between the main bearing caps. now simply drop a spider gear down from top and slap the other. hold the bottom one up and rotate the prop till the main pin holes will line up.
@TheMarkeyz64 Жыл бұрын
Where do all the washer go with the spider gears in the differential gear kit?
@zanehaynie8352 Жыл бұрын
Does it matter if you mix those two spider gears like do you have to put the top gear back on top and bottom back on bottom
@Kratos-kq9fe2 жыл бұрын
Thank you young man that was very very helpful !
@jamesfritz53752 жыл бұрын
I call bullshit it's not that easy it just doesn't go in!
@gkz8712 жыл бұрын
there is two washer beside the two small gears, this way is difficult operate in a real truck
@elieli13472 жыл бұрын
Why would the spyder gear shaft break
@outwiththem2 жыл бұрын
06:12 You didnt tight the spyder gear pin retainer at all.. Geeee..
@kennysamples21962 жыл бұрын
This was very helpful thanks a lot.
@David-lb4te2 жыл бұрын
"Side gears" are actually called planetary gears. "Spider gears" are called sun gears.
@Mohamedseddek2 жыл бұрын
♥️👍👍👍👍
@erickmagana93532 жыл бұрын
I’m trying to get my center pin out but the ring gear doesn’t let it come out all the way.
@pierrec95192 жыл бұрын
Does having the bearing caps removed make a difference? I can't get my spiders gears in place as I can't seem to get my side gears pushed in enough to allow the spider gears to sit lower on side gears.
@ruinedgti6511 Жыл бұрын
how did you end up getting this done, having the same issue
@luizchevelle72182 жыл бұрын
Thank you very much Illustrated Man! You saved my life.
@tannerhasdowns2 жыл бұрын
Fought with a set of spider gears for like 2 hours trying to get them lined up perfectly should have watcht his video first
@spdnbeerman3 жыл бұрын
Don't take your car axle to this dude
@user-hu4hx6bm6m3 жыл бұрын
Brother - Your video save me today - Spider gears got loose while rebuilding my Van rear end differential at home-Thank YOU!!
@joemoore37803 жыл бұрын
Thanks for this video! It helped me out of a jam
@kenactofkindness40173 жыл бұрын
learning and will try it on my own save 2000
@robinlangois88523 жыл бұрын
Thanks for video BUT I put my spider gears back in and all is tight. But when I turn the axle is there supposed to be a little play on the spider gears ?
@counterthirty6 ай бұрын
Small amount
@cresposaidso42653 жыл бұрын
Bro you saved my life just now. I had the right idea but not the right set up method
@james-im1sj3 жыл бұрын
So glad this video was made going crazy trying to figure that out .
@OscarPerez-gu3yd3 жыл бұрын
I’m sure you had good information but it was so hard to hear what you were saying because of the background noise and because your voice did not carry well to the mic on the camera. Maybe if you wore a mic on your person it might help
@thephotographyofbriank.kre68713 жыл бұрын
Thanks!! Needed this!!
@michaeldunagan78383 жыл бұрын
Cannot mumble if you ain't mic'ed. Would have been good information to hear...... Thumbs down due to production.
@ECG32-584 жыл бұрын
Just check the shit
@elmarlumakin6064 жыл бұрын
Sir how to order 8.6 gm spider gear set 10 bolts? I need for Chevrolet Silverado 1500 MY 2000 Thanks for the video
@TJ-dx5xq4 жыл бұрын
Nice video. Thanks much!
@66and72nova14 жыл бұрын
I get the just of the video. However, if you're going to teach someone how to install the used spider gears to it the right way. First. Look at the side gears teeth and find the side gear that mimics the ring gear, drive coast. The drive side will have more wear. Now install it on the passenger side and the one on the passenger side to the drive side. The pinion gears should be flipped 180 too. This will allow the pinion gears to drive on what was the coast side of the spider gears. Increasing the life of used spider gears.
@spelunkerd3 жыл бұрын
Oh, so you are rotating the gears so long term wear is even, much like rotating tires to get longer life. Cool.
@66and72nova13 жыл бұрын
@@spelunkerd, Let's say you have a posi or open carry. Rotating the spider gears must be done exactly. Driver's side side gear to passenger side. Passenger side to Driver's side. Pinion gear closest to cross shaft bolt moved to opposite side farthest away. Farthest away spider gear moved closest to cross shaft pin bolt. This will allow cause the spider gears to drive now on the coast side instead of continuously driving on the drive side. Coast side of the gears will have less wear. If the spiders are extremely worn then best to replace them.
@richardspaulding50353 жыл бұрын
My dam truck is 40 years old, I am not worried about how much longer the gears will last will last LOL.
@66and72nova13 жыл бұрын
@@richardspaulding5035 Yep, that's why, Why people sell a used 12 bolt car or truck rearend they want 500.00 to 800.00 when all you have to start with is a bare housing. Everything else is worn out.
@blkbird15544 жыл бұрын
Man if I knew this I would never got myself in this mess
@MicroSoftner4 жыл бұрын
Did ya fix the mess?
@noway93694 жыл бұрын
You might want to be worried about that broken wheel stud
@joegranozio86724 жыл бұрын
Lol it's just a trainer vehicle it will never leave the schools grounds but u are absolutely rite in the real world!👌🏽😉
@ralphfuller86804 жыл бұрын
Do better with your audio
@joegranozio86724 жыл бұрын
👍🏼
@michaelmcclure86734 жыл бұрын
Thanks, you showed me what I needed. Might talk a bit louder next video.
@dpedro91504 жыл бұрын
You made it look easy. Hope it works that way for me.
@yeudsiegal52854 жыл бұрын
What about the yellow springs?
@nofx14204 жыл бұрын
Good job bro, great video 👍
@jmj_d52075 жыл бұрын
If i have my truck in jack stands and put it on drive only one rear tire spins is that normal ?
@gregl56775 жыл бұрын
Depends if its open or locker or lsd
@jmj_d52075 жыл бұрын
@@gregl5677 its an open differential
@jmj_d52075 жыл бұрын
@@gregl5677 its from a 2000 chevy silverado i guess code for it is a gt4 diff
@gregl56775 жыл бұрын
@@jmj_d5207 does it have a g80 code next to gt4? If not its fine its a open diff g80 code was fore posi trac. Unless the rearend had a locker put in it at some point.
@jmj_d52075 жыл бұрын
@@gregl5677 no no g80 just gt4
@metalmaniaxx5 жыл бұрын
Good video,you should really put some thread locker on the shaft bolt
@Marcosvlogs8475 жыл бұрын
I really love this video cool
@ramman55285 жыл бұрын
you forgot the washers on inside of the side gears
@MicroSoftner4 жыл бұрын
I think I see em already on ?
@robwells57535 жыл бұрын
thanks mate good referesher vid. i cant find a vid on the hyster im going to be operating. its old n old n nasty lookin unit with a six cyl cummins just not sure of the model yet
@danielantoniozd266 жыл бұрын
made it look easy!
@darrell11williams6 жыл бұрын
This look so easy I have 04 gmc yukon my spider gear is bad this shop said it will take 2 days and the labor will be $475 to put on after me seeing this video I'm not no mechanic but I think I can do this great video
Пікірлер
How did the gears not fall out when you replace the splines
Without you today, it would have been a worse day. Thank you Homie. Straight to the point, I love it
They are a pain in the ass without the proper tools when putting in however when you use a dissolve stitches to pull the spider gear in so it doesn’t fall out it makes thing a lot easier
Great
Does the baring cap need to be removed before putting the spider gear in? Please help 😅
No. It does not. However, if you’ve rounded off the hex on your lock bolt you can’t get a ratchet with socket in there to remove it.
Thx. Good demonstration
Thank,s
you must know how to time the gears. this should take five minutes max. rotate the prop till the small pin bolt is centered between the main bearing caps. now simply drop a spider gear down from top and slap the other. hold the bottom one up and rotate the prop till the main pin holes will line up.
Where do all the washer go with the spider gears in the differential gear kit?
Does it matter if you mix those two spider gears like do you have to put the top gear back on top and bottom back on bottom
Thank you young man that was very very helpful !
I call bullshit it's not that easy it just doesn't go in!
there is two washer beside the two small gears, this way is difficult operate in a real truck
Why would the spyder gear shaft break
06:12 You didnt tight the spyder gear pin retainer at all.. Geeee..
This was very helpful thanks a lot.
"Side gears" are actually called planetary gears. "Spider gears" are called sun gears.
♥️👍👍👍👍
I’m trying to get my center pin out but the ring gear doesn’t let it come out all the way.
Does having the bearing caps removed make a difference? I can't get my spiders gears in place as I can't seem to get my side gears pushed in enough to allow the spider gears to sit lower on side gears.
how did you end up getting this done, having the same issue
Thank you very much Illustrated Man! You saved my life.
Fought with a set of spider gears for like 2 hours trying to get them lined up perfectly should have watcht his video first
Don't take your car axle to this dude
Brother - Your video save me today - Spider gears got loose while rebuilding my Van rear end differential at home-Thank YOU!!
Thanks for this video! It helped me out of a jam
learning and will try it on my own save 2000
Thanks for video BUT I put my spider gears back in and all is tight. But when I turn the axle is there supposed to be a little play on the spider gears ?
Small amount
Bro you saved my life just now. I had the right idea but not the right set up method
So glad this video was made going crazy trying to figure that out .
I’m sure you had good information but it was so hard to hear what you were saying because of the background noise and because your voice did not carry well to the mic on the camera. Maybe if you wore a mic on your person it might help
Thanks!! Needed this!!
Cannot mumble if you ain't mic'ed. Would have been good information to hear...... Thumbs down due to production.
Just check the shit
Sir how to order 8.6 gm spider gear set 10 bolts? I need for Chevrolet Silverado 1500 MY 2000 Thanks for the video
Nice video. Thanks much!
I get the just of the video. However, if you're going to teach someone how to install the used spider gears to it the right way. First. Look at the side gears teeth and find the side gear that mimics the ring gear, drive coast. The drive side will have more wear. Now install it on the passenger side and the one on the passenger side to the drive side. The pinion gears should be flipped 180 too. This will allow the pinion gears to drive on what was the coast side of the spider gears. Increasing the life of used spider gears.
Oh, so you are rotating the gears so long term wear is even, much like rotating tires to get longer life. Cool.
@@spelunkerd, Let's say you have a posi or open carry. Rotating the spider gears must be done exactly. Driver's side side gear to passenger side. Passenger side to Driver's side. Pinion gear closest to cross shaft bolt moved to opposite side farthest away. Farthest away spider gear moved closest to cross shaft pin bolt. This will allow cause the spider gears to drive now on the coast side instead of continuously driving on the drive side. Coast side of the gears will have less wear. If the spiders are extremely worn then best to replace them.
My dam truck is 40 years old, I am not worried about how much longer the gears will last will last LOL.
@@richardspaulding5035 Yep, that's why, Why people sell a used 12 bolt car or truck rearend they want 500.00 to 800.00 when all you have to start with is a bare housing. Everything else is worn out.
Man if I knew this I would never got myself in this mess
Did ya fix the mess?
You might want to be worried about that broken wheel stud
Lol it's just a trainer vehicle it will never leave the schools grounds but u are absolutely rite in the real world!👌🏽😉
Do better with your audio
👍🏼
Thanks, you showed me what I needed. Might talk a bit louder next video.
You made it look easy. Hope it works that way for me.
What about the yellow springs?
Good job bro, great video 👍
If i have my truck in jack stands and put it on drive only one rear tire spins is that normal ?
Depends if its open or locker or lsd
@@gregl5677 its an open differential
@@gregl5677 its from a 2000 chevy silverado i guess code for it is a gt4 diff
@@jmj_d5207 does it have a g80 code next to gt4? If not its fine its a open diff g80 code was fore posi trac. Unless the rearend had a locker put in it at some point.
@@gregl5677 no no g80 just gt4
Good video,you should really put some thread locker on the shaft bolt
I really love this video cool
you forgot the washers on inside of the side gears
I think I see em already on ?
thanks mate good referesher vid. i cant find a vid on the hyster im going to be operating. its old n old n nasty lookin unit with a six cyl cummins just not sure of the model yet
made it look easy!
This look so easy I have 04 gmc yukon my spider gear is bad this shop said it will take 2 days and the labor will be $475 to put on after me seeing this video I'm not no mechanic but I think I can do this great video