beautiful car by the way

Yessa 🔥🔥🔥👀

The intake you had on was either a Factory or an OEM replacement. Dorman intakes did not have a threaded ignition coil spot, and the coolant crossovers were plastic. That one right there was probably fine in a horsepower aspect. Depends how long the car sat but id highly doubt its a dorman one being that they only just recently updated their own design of the intake on the 4.6.

Nice job! Made it look easy.

@AutoExec1

5 ай бұрын

Thank you, I've actually sold this car. I have a new project I'm about to start filming.

sounds good

@AutoExec1

10 ай бұрын

Thank you, I love the way these 2v mustangs sound.

That air filter was installed in bout 2009. lol! nice job.

@AutoExec1

10 ай бұрын

Yeah it sure looked like it lol and thank you.

Sweet ! New gear for the whip ..

@AutoExec1

10 ай бұрын

Yessir. There's alot coming for this car.

@jakedean8560

10 ай бұрын

​@@AutoExec1Go 4:10s. I have an 01 gt 5 speed and was trying to decide between those and 3:73s. 4:10s were the better choice, 3:73s would've felt too slow

@AutoExec1

10 ай бұрын

@@jakedean8560 I will definitely be doing gears on this car in the near future. Did you ever run yours at a track?

nice warm air intake

recommend putting the filter cover back on to help intake air temps especially being in the south cooler air is denser and makes more power great vid id also recommend getting high flo cats i think those GTs come with 6 convertors so that will help with power to replace or remove them

@AutoExec1

10 ай бұрын

Is that because the air from the engine bay will be making AIT's higher and putting it back in the box will keep that hot air from the intake? I've heard alot of people use the phrase "hot air intake" when talking about open intake systems. And the rear (easily accessible cats) are gone. I need to get an O2 sensor put on it.

@dakotajones8010

10 ай бұрын

@DavidMcall yes it'll pull in hot engine bay air my Steeda intake gets STUPID hot if I'm idling, lately in TX its been over 100 so intake Temps coming home have been 115+

@jeffsnyder2051

10 ай бұрын

4 cats

@Peculiarsafe83

10 ай бұрын

@@AutoExec1Enclosing the filter to draw air from outside of the hot engine bay air should keep the IAT temperature lower. They design it like this from the factory because they know that the air outside of the engine bay is less hot. Which is why they all draw air from a part of your fender which sucks in air past your headlights. This is why there are cutouts in the metal fender where your factory Airbox sits at.

i heard you have to close off the intake in a box in that corner or it just circulates hot air n not cold air from how you removed the stock box that gets the regular air from behind that headlight but i just heard it kind of is harmful to use recirculating hot air from the engine bay under that hood but idk , just a thought

I'm not a fan of hot air intakes setups but other than that, nice mods. Nothing crazy.

@lostsoul192d5

11 ай бұрын

I run a filter in the same location and I have cool iats, take your myths elsewhere

@AutoExec1

10 ай бұрын

I've heard that the intake needs to be kept in the box for cooler air so it doesn't get heat soaked by engine heat. And thank you.

It looks just like my 04 Mustang, GT, sweet ride man of an automatic, too dark, shadow gray

@AutoExec1

3 ай бұрын

I do love these cars.

Thank god somebody finally replaced the Manifold with the Ford Performance one that was designed for the car itself. They tested that Doorman designed manifold. It actually makes the car lose 20HP because of how it’s designed. And please fix that “hot air intake”. My Suburban had a K&N one that was in there from the previous owner and my IAT temperatures were through the roof with it sucking in hot engine bay air while idling. Switched back over to the stock AirBox/AirAid intake tube combo and now it runs 20+ degrees lower IAT temperatures when it’s 90+ degrees outside.

@AutoExec1

10 ай бұрын

Yeah that doorman manifold is garbage. I'm definitely going to be fixing the intake very soon lol that's a huge AIT difference.

I ran nitrous express on my 4.6 (got videos on my channel) and i just got a kit in for my foxbody. Imo you cant go wrong with nitrous express.

@AutoExec1

10 ай бұрын

That's the kit I got. I'm planning on doing a 75 wet shot. What did you do on yours? Is it easy to set up? I'm going to check out your videos.

@TheModAddict

10 ай бұрын

@@AutoExec1 easy to setup. I ran a 125 shot. Fourpointsixchris sprays a 150shot on his 4.6

You should throw on an oil catch can asap, it'll save that manifold down the road

@AutoExec1

10 ай бұрын

I'll look into that thanks. I wonder if American muscle sells them.

@jaymoney8793

4 ай бұрын

I also appreciate you for this, I have been on “edge” about getting a oil catch can, but for sure now I will install one!

Keep the updates coming.. what kind of exhaust and if it is stock that the next

@AutoExec1

10 ай бұрын

I definitely will. It has catless X pipe to flomaster 40's. I want to do a different style x pipe like BBK in the future. The next modification will be nitrous oxide.

Put a steeda air intake on it with the heat sheild, bbk plenum and throttle body, 373 gear, X pipe, cat back and tune. If the funds allow long tubes. That’ll make that car really wake up.

@AutoExec1

8 ай бұрын

It had the catless X pipe and Flowmaster 40s. I actually sold this one and am currently looking at another broken one to fix.

How do you tell if your intake manifold is OEM or not??

@AutoExec1

5 ай бұрын

I show a good example in this video. It's sort of hard to explain through text.

@BobbyG3752

5 ай бұрын

@@AutoExec1 i found the dorman looking wings , my luck.

@AutoExec1

5 ай бұрын

@robertgrooms8246 that sucks. Definitely get a ford original manifold, it makes a big difference.

Are you interested in talking about a cooperation?

I didn't see a spark plug change .

@AutoExec1

24 күн бұрын

Watch it again. 😁

@marclebouthillier9937

24 күн бұрын

@@AutoExec1 I will ...must of mist it .

Why do you think you lose 25hp with that Dorman intake? I just had one put on my car and it runs just as strong. Didn’t lose any power at all.

@AutoExec1

8 күн бұрын

I saw a video that did a dyno comparison between a stock manifold and a Dorman. Amd sure enough the car was 25 hp down with the Dorman. Could have been heatsoaked though.