2018 6th Gen Camaro Sound System Install

Автокөліктер мен көлік құралдары

Overview of a Dual 10" Subwoofer install into my 2018 Camaro 1SS 1LE.
Subscribe to the Channel and Instagram @
essmotorsports
if you want early sneak peeks on what I am working on.
Thanks for the support!
Links:
Line output converter:
amzn.to/3ohWeDN
Dual 10" box:
amzn.to/3yUC5IN
Current Mods:
2018 Camaro 1SS 1LE
180 Deg F SDPC Thermostat
LT2 Intake Manifold
Rotofab Intake sound tube delete, dry filter
Stock Dual Mode Exhaust
LED Side Marker Lights V1motors
2SS Leather Knee Pads/Bolsters

Пікірлер: 89

  • @nobodymporta
    @nobodymporta Жыл бұрын

    2023 ...I'm install on a 2019 ss ..thank u ..sir 🫡🫡

  • @davidmorgan3609
    @davidmorgan36092 жыл бұрын

    Rattle comes from rear speaker deck plate. Try pushing up on plate while bass is playing

  • @19gkk1le5
    @19gkk1le53 жыл бұрын

    Subbed thanks for the info bro

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    NP i figured I couldn't be the only person wanting more bass from the non bose 1le systems.

  • @thedjrush
    @thedjrush3 жыл бұрын

    Subscribed bro

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    Thanks! Appreciate the support!

  • @oscarsanchez9336
    @oscarsanchez93362 жыл бұрын

    Hello thank you for the video I’m trying to do the same in my 2016 camaro 2ss I have a question do you think I can use the rear trunk speakers to connect the line input converter or have to be the one are using in the video

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    My plan was to use trunk speakers until I found out I didn't have them in a 1ss! Haha so yeah I think you can use them. With the bose amplified system just have to see if the chimes for door and stuff come through louder. If your just using it for just subwoofer I would think the low pass filter on the amplifier would take those higher frequencies out and you would be good.

  • @jayliinn._3249
    @jayliinn._32492 жыл бұрын

    So did you tie in the left and right positive & negative wires from the converter if though you ran them to one side?

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    Yep. You don't get right and left channel on the sub then but that is usually how I do it and it never bothers me or even notice it.

  • @turtletalker
    @turtletalker3 жыл бұрын

    Your sooooooooo close to 3hundred, I hope you get 3hundred soon :)

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    Right! Thanks man! It sure is fun watching this channel grow. Slow but none the less. More coming as well with tuning and more driving!

  • @squeek797
    @squeek797 Жыл бұрын

    That is hooked up to the factory radio? I love that hood . Is it wrapped or carbon fiber hood?

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    Yes get signal from factory rear speakers. The hood is the factory Camaro 1LE wrapped hood.

  • @blackhammmer7849
    @blackhammmer78496 ай бұрын

    Rear deck lid mine does the same just dyno mat it

  • @brandonrea6151
    @brandonrea61512 жыл бұрын

    Dose your batter die at all bc I kinda have the same set up but every now and then my car won’t start

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    My battery would drain before I put a system in. If it's going to sit a while I usually just hook up a trickle charger.

  • @lucassanmiguel107
    @lucassanmiguel1074 ай бұрын

    can you explain which wires in the door panel you tap into? I haven’t done it yet. but is there 2 or 4 wires in the door speaker harness?

  • @EssMotorsports

    @EssMotorsports

    4 ай бұрын

    You tap into the two wires going to the rear speaker. I only tapped into the Passenger side, to make it simple. So it makes the sub a single channel based off of the passenger side, vs if you tap off of both PS and DS you could wire your dual subs to each side.

  • @1eliaskno
    @1eliaskno3 жыл бұрын

    I did the same think and it sounds good but what's weird is that when I close the doors it gets like a bass sound even tho I don't have music on. I even added extra ground and it does not eliminate the sound. Any other tips will be greatly appreciated

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    That is weird if it happens only when you close the door. I was going to say if it happens when the amp is turning ON then get a pop stop eliminator. Is your gain set too high that it is picking up the slight electrical noise? I'd try turning gain down see if that helps.

  • @H0llyw00d-bruh

    @H0llyw00d-bruh

    3 жыл бұрын

    Bro where did you ground your converter to? I tried grounding at the amp and my amp is grounded to the camaro ground which isn't working. My amp won't turn on neither will my lc2i pro (converter).

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    I grounded the kicker converter to the battery lug. Did you tie both negatives together and both positives? If that would cause an issue if they weren't? Also make sure you have voltage from the speaker, could be blown?

  • @thedjrush

    @thedjrush

    3 жыл бұрын

    I'm was using a active line converter LC7I from audio control and since is uses the speaker signal to turn on instead of relying on a remote signal I don't have a issues with any random subwoofer pops you should look into it

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    I will have too maybe for just the random pop issue. It's very faint when the radio comes on and off but I notice it.

  • @thedjrush
    @thedjrush3 жыл бұрын

    May I recommend the audio control lc2i if you want a better signal for your bass as it is an active (Powered) line converter

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    I have seen a lot of people use that. I will have to check it out.

  • @thedjrush

    @thedjrush

    3 жыл бұрын

    @@EssMotorsports yeah in terms of accessibility it will definitely sound better as it also has a function to restore bass rolloff when raising the volume of the stock system

  • @orlandochiludo1786
    @orlandochiludo17862 жыл бұрын

    I’m having trouble getting the loc converter to turn on my amp any idea what it can be

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    Yeah I had the same issue right away. Make sure you hook up the ground connection wire on the LOC. I didn't do that right away and my amp wouldn't turn on.

  • @lukeLT1ss
    @lukeLT1ss Жыл бұрын

    What was the negative and positive on that speaker? what were the colors?

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    Good question.. I don't remember exactly but typically ground is black or it will be colored with a black stripe. Try this first and don't clip panel back in until u try system out first to make sure it works.

  • @BrandonG0726
    @BrandonG0726 Жыл бұрын

    Where did you get the remote wire hooked up? Is it in the fuses box? I had a 2010 n a 2013 Camaro and there used to be a dedicated remote wire where the vehicle's amp wiring was. Now with the 2018 im trying to figure out where the wire is at. Any inputs???

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    I used an automatic turn on that senses when speaker wires turn on, and then turns amp on.

  • @carlosgarcia2873

    @carlosgarcia2873

    3 ай бұрын

    Hello I’m having same issue were did buy that wire to make the remote work….also do you get any engine noise how you currently have it

  • @BrandonG0726

    @BrandonG0726

    3 ай бұрын

    The RCA converter came w a remote wire. After hooking up everything I did have a loud noise when driving, I unhooked one of the microphones from (either side) the door. N sound is AMAZING!!!

  • @percycarr4436
    @percycarr44362 жыл бұрын

    How u get the speeker box in the trunk tho? Kuz I have 2 12's in a prefab subwoofer box an im not trying to buy another subwoofer box

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    I measured before I bought the box and it fits going through the rear seat opening.

  • @percycarr4436

    @percycarr4436

    2 жыл бұрын

    @@EssMotorsports ok

  • @devoncannon6773
    @devoncannon67733 жыл бұрын

    Which is the positive and negative on the speaker wire. Yellow and green wire with black stripe

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    I cannot remember, I'm sure I used a multi-meter and tested it to figure it out.

  • @devoncannon6773

    @devoncannon6773

    3 жыл бұрын

    @@EssMotorsports did you hook the blue wire to the battery? My amp seems to not shut off when I do that

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    If your using the same kicker product there is a wiring diagram on the back of it. The blue wire is the amp turn on and the black wire was for ground.

  • @tylerpowell3257
    @tylerpowell3257 Жыл бұрын

    can i use this set up in a 2022 1ss 1le

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    Yeah there should be no reason u couldn't. I'm assuming the 1SS 1LEs still don't have an factory amp like mine didn't. 👍

  • @Djxtenz
    @Djxtenz3 жыл бұрын

    What’s going on bro I have a Camaro 1ls 2021 and I just installed my subs and when ever I turn the car on I hear a roaring noise coming from my subs what could I do to fix it

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    If you have a factory amp, Sounds like it could be a feedback loop caused by your active noise canceling mics. I'm just guessing from what I have read on the forums but that would be a good first place to start.

  • @Djxtenz

    @Djxtenz

    3 жыл бұрын

    @@EssMotorsports did your car have a factory amp ? I think our cars are the same

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    No it didn't. The 1ss 1le didn't have amps because the mag ride controller was there. 2ss might be different.

  • @Djxtenz

    @Djxtenz

    3 жыл бұрын

    @@EssMotorsports oh okay did you have any problems with roaring noises with your sub install ?

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    No. I have a slight pop on startup and shutdown but it's not that noticeable. Check ground wires etc. Make sure your not chasing wiring issue first.

  • @squeek797
    @squeek797 Жыл бұрын

    Do I need a compasitor. With just one sub ?

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    No u don't. There is argument that capacitor is harder on charging system as well. So for one sub I would leave out. I have 2 10s in my silverado with no capacitor and it's all good

  • @squeek797

    @squeek797

    Жыл бұрын

    @@EssMotorsports oh ok thanks bro cause I’m installing a single 12 an I thought it would need another recharging route. In my 2017 Camaro lt

  • @JaxonWeems
    @JaxonWeemsАй бұрын

    let me just ask why the heck you are sitting in a running car inside a closed garage? nvm that it sounds great!

  • @EssMotorsports

    @EssMotorsports

    Ай бұрын

    Ah it's called night. The door was open 🤣

  • @JaxonWeems

    @JaxonWeems

    Ай бұрын

    @@EssMotorsports how much did you spend total on this install?

  • @EssMotorsports

    @EssMotorsports

    Ай бұрын

    @JaxonWeems I didn't spend much cause I was reusing old sound equipment. The amp, capacitor, speakers, even most of the wire was reused from previous vehicles. The box was cheap and the new fuses was few bucks but not bad. Everything new now a days would be probably 700 bucks.

  • @athomas3082
    @athomas30822 жыл бұрын

    what size is the box

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    13x30 x13 high. Fit really good in the trunk space.

  • @omarionmitchell7635
    @omarionmitchell76353 жыл бұрын

    how did u get to the speaker

  • @EssMotorsports

    @EssMotorsports

    3 жыл бұрын

    You have to pull the side panel off that is covering the speaker. There is another good video on KZread that shows more detail on what to remove. Everything is held in with clips and couple small screws.

  • @Camerors
    @Camerors9 ай бұрын

    Got everything hooked up on my camero but for some reason my trunk won’t open and when I lock the doors my alarm doesn’t make any noise? Hopefully someone could tell me what it is and how to resolve it

  • @EssMotorsports

    @EssMotorsports

    9 ай бұрын

    Humm it shouldn't have messed with any of that. Did u tap into a fuse somewhere and maybe blow it?

  • @Camerors

    @Camerors

    9 ай бұрын

    Where did you put remote wire? I think that’s what my problem was

  • @EssMotorsports

    @EssMotorsports

    9 ай бұрын

    @MianteWinters I used the kicker keyloc tied into speaker wire for the remote turn on for the amplifier. Check out my other camaro sound system video. Should have link for Keyloc that I used

  • @Camerors

    @Camerors

    9 ай бұрын

    @@EssMotorsports is that supposed to be better ? Because I used the converter in this video and I’ve been having so many issues. What gauge wires are you running ? What kit are you using ? I don’t think you really mentioned everything you used

  • @Camerors

    @Camerors

    9 ай бұрын

    Kinda new to the camero industry and for some reason I’ve been having issues. Haven’t in other vehicles

  • @NEMPLS
    @NEMPLS2 жыл бұрын

    Shouldn't bolt amplifier to the sub box. Can really screw up your amplifier with the vibrations I've heard.

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    I've done this for years in multiple cars, never been an issue. I space it off a little so heat is not a factor. Car probably shakes more than the box does! Haha

  • @NEMPLS

    @NEMPLS

    2 жыл бұрын

    @@EssMotorsports ok, just what I've heard. Looks good tho.

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    @@NEMPLS yeah....probably not the best in terms of electrical interference but works good enough.

  • @NEMPLS

    @NEMPLS

    2 жыл бұрын

    @@EssMotorsports it's a really clean set up you did. I've seen alot of videos of some really crappy installs on camaros. I hate untucked exposed wires and electrical tape videos. You should be proud.

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    @@NEMPLS Thanks man! I try! 😄

  • @denniswestry5223
    @denniswestry522311 ай бұрын

    Rear deck

  • @ss6thgen336
    @ss6thgen3362 жыл бұрын

    were dis you hook up the remote wire to

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    The high level inputs are spliced into the passenger side rear speaker. The remote turn on lead goes to amp. Also have to hook up ground connection which I went to the battery.

  • @ss6thgen336

    @ss6thgen336

    2 жыл бұрын

    i connected the the remote wire from the converter to the sub amp but nothing well turn on not even the converter

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    @@ss6thgen336 make sure ground on the converter is connected or it won't turn on.

  • @ss6thgen336

    @ss6thgen336

    2 жыл бұрын

    the converter turned on now but the remote goes from the converter to the amp remote right?

  • @EssMotorsports

    @EssMotorsports

    2 жыл бұрын

    Yeah it goes to amp turn on connection. Should be labeled or reference manual of amp

  • @Wannakatana2112
    @Wannakatana2112 Жыл бұрын

    No offense but way too much chatter/fluff, and start at one end and flow through to the last end. Jumps around too much. Start at the battery for example and follow it back to the subwoofer, something like that. Linear.

  • @EssMotorsports

    @EssMotorsports

    Жыл бұрын

    I do like to talk a lot! Work in progress getting to the point while explaining everything thorough enough.

Келесі