Nice stuff. That "equal spacer" could use a wingnut on a small bolt to lock it in place to keep going without error. Thanks for the link!

For the tire tread depth gauge and the bolt&nut sorter you can color the legends a little easier if you switch filaments to black (or other contrasting color) for the last couple layers. That'll save the marker issues that I always have of the ink running down and bleeding across the face of the part. The issue with the marker on the square is probably because the markings were debossed (sunken into the surface) instead of embossed (sticking out of the surface) like the tread depth gauge and bolt&nut sorter. But, since that was printed with the markings on a vertical surface, the color changing trick would be a major pain even on a printer that has decent M600 support.

Did you just super glue what is supposed to be a replaceable boxcutter blade into that "faker knife"?

Why would I go through the tedious task of making that brush when I could do the same job with a cheap 25-cent chip brush?

In #2, how do you change the blade, if it's all glued ?

@jasond9824

2 жыл бұрын

It appears to lock in the blade out position, but not lock in the safe to carry position. What a stupid overall design flaw

@chrisnupp7097

2 жыл бұрын

@@jasond9824 I printed one, it locks it into both positions.

@chrisnupp7097

2 жыл бұрын

It's not supposed to be glued in place. There's a tab by the blade divots (where the blade locks in place) that you can push out of the way to remove the blade and replace it.

@theanimationkingdom4

2 жыл бұрын

U cant.

Thank you for the update.

I enjoy this type of video and appreciate the time and effort you put into it. It's a great way to get ideas for future prints. Thanks!

@3DPrintsBuilds

2 жыл бұрын

Thanks!

Spray can handle needs an adjustable end stop so u can just sqeeze handle and set the exact spray volume without the need to hold just the right squeeze to get what u want for spray pattern.

Look so cool that bro

for the nuts & bolts shorter, you should add the size to the nut side

What settings did you have to change on that first print? I’ve had that problem with one of my printers and don’t know how to fix it.

@3DPrintsBuilds

2 жыл бұрын

I changed line width from 0.3 to 0.4mm

i like the concept very much 💕👌👍

Do you have your print settings displayed anywhere? I just got a ender, and my prints never come out looking that nice.

@3DPrintsBuilds

2 жыл бұрын

Cura profile for Ender 3 V2: www.mediafire.com/file/sxlrfx1jiebkcif/Ender_V2_Basic_settings.curaprofile/file

Привет а ты не печатал корректоры в фары для е39. Спс если есть стл скинь плиз. Удачи

Only spacer and bolts measure tool are useful. The rest are good only in collecting a dust or filling recycle bin.

what cura settings are you using for those clean prints?

@3DPrintsBuilds

2 жыл бұрын

I have different settings for different prints, but I can share my basic Ender v2 PLA profile: bit.ly/2Zg40Ff

Awesome video and content 👌 what does R. F on the oil wrench mean?

@3DPrintsBuilds

2 жыл бұрын

Thanks! The R. F. are the initials of the designer. Rusty_Fly

I have the same problem witch my 3d prints that you in first print. What did settings you change.

@3DPrintsBuilds

2 жыл бұрын

Changed line width back to 0.4mm

The nr10 yellow bolt and nut sorter.. you got a link? For the file

@3DPrintsBuilds

2 жыл бұрын

Link in the description.

On your recessed groves,(like the carpenters square) you should try a wax crayon 🖍 instead of a sharpie. It works great. You can rub off any excess with a paper towel for clean marks.

@3DPrintsBuilds

2 жыл бұрын

Thank you for the idea. I will try it someday.

nice combination of useful tools. keep uploading. good luck .

@3DPrintsBuilds

2 жыл бұрын

Thanks!

What did you applied to the spring?

@3DPrintsBuilds

2 жыл бұрын

I applied grease.

Nice .. Can I have the wood burner link and permanent marker link?

@3DPrintsBuilds

2 жыл бұрын

Wood burner: s.zbanx.com/r/0oD7Tzj2iDwR Permanent marker: euro-industry.com/main.php?index=details&cat=8&prod=23201550&lang=de

Nr. 1 Trim/Clip popper - what filament is it, please?

@3DPrintsBuilds

2 жыл бұрын

PLA

@S....

2 жыл бұрын

@@3DPrintsBuilds Dude.. what brand / color? xD

@3DPrintsBuilds

2 жыл бұрын

@@S.... Gembird Gold Metal PLA

Print = 'auxiliary handle' for drill machine.

It's more expensive to make these than it is to buy ones that are readily available on Amazon lol

@pcerano742

3 ай бұрын

Lol. Most of these prints probably cost less than $1.50.

@styxx0500

3 ай бұрын

@@pcerano742 and yet, they aren't even worth $1.00 🤣

You have a typo in your ad, the word you want is "stuff" not staff

i saw that 3d guns folder, can't stop the signal.

👍 👍 👍 👍

amd why didnt you loosen the oil filter cap that fit perfectly?

@alexistaboada5759

2 жыл бұрын

Bc the tool would have disintegrated with any amount of load

Whipping that blade around was freaking me out.

Hi. Which slicer do you use?

@3DPrintsBuilds

2 жыл бұрын

Cura

@granul555

2 жыл бұрын

@@3DPrintsBuilds How did you get the numbers printed on top? They look bad to me when printed.

@3DPrintsBuilds

2 жыл бұрын

@@granul555 Look over your print settings. Maybe you need to slower down or change layer height.

@granul555

2 жыл бұрын

@@3DPrintsBuilds Can you please share your Cura settings?

@3DPrintsBuilds

2 жыл бұрын

@@granul555 I use different settings with different prints and printers. Here is one of my Ender V2 settings: www.mediafire.com/file/v0l8ifqz7seiazs/Ender_v2_0.2mm.curaprofile/file

🔥💕👌👍

Lol... why did you glue the blade into you knife?

I will have to get my printer set up so I can utilise it better.

Полезные инструменты? Ну уж линейку то можно купить в магазине. Как и почти всё остальное

Is everybody just that messed up every one of those things that I see I don’t have the design I don’t have the figure out the way to print it or make it I don’t have to buy the printing material to do it it’s already there all I Gotta do is go to the damn store and buy it and once I figure out the time spent and the printing material it’ll be about 75% cheaperIf I just go buy it

@andrewjackman8926

Жыл бұрын

Got a headache reading your comment. No punctuation?

Игрушки и ее более того.

Jump to 8:43 believe me, watch till the end. Don't waste your time like I did.

Hii

If you have to use super glue on a removable part it's not convenient

Or maybe just buy a cutter and save the 6 hour of printing

gdzie na stole kroisz.. matka by Ci zaraz pokazała ciachanie na stole

☝️ I'm the first person to design "print in place" brooms and brushes about 8 years ago.

Самоделки полная хуйня (с) Доктор Дью ((((

Can't you spell?

Useless

Seriously ? What have you done here ? You are not the owner of designs, you just publish timelapses of your printer printing other guys work !

@warmesuppe

2 жыл бұрын

Where does he/she claim that?

@LoreLibrary-Official

2 жыл бұрын

Where do they claim its theirs

@brandielee7971

2 жыл бұрын

They don't claim the designs are theirs, and they link the the stuff. It's just to make people aware of the files

@MrToufou54

2 жыл бұрын

So, yes everybody, but where are the credits (in the video) ??? Where is the creativity ? What does this video give more than a search on stl search engines ? I'm just saying that there is no work on this video... I'm here for having more that just that I could by myself

@LoreLibrary-Official

2 жыл бұрын

@@MrToufou54 yes u can do it yourself..this just show to people that these file exist..the maker of the file allot them to do this cuz its freeeeeeeeee

I need one of those Faker ꓘnifes.... lol Thanks for the share.. Just stumbled upon your channel!!!