Great video!! Question can that solenoid by the shifter gears for park prevent the truck from starting? I have change the solenoid against the firewall under the hood with a new starter & now I’m using a screwdriver to start it with the same solenoid on the firewall!! SomeXs it would start & someXs it won’t then I would have to use the screwdriver..
@aaronsroseКүн бұрын
I don't think the column would do it, but the neutral safety switch on the trans might
@bljblj26Күн бұрын
Thanks Bud..
@arnoldmosk494Күн бұрын
To avoid damage S&S tell’s you in the manual to remove the pushrods in the first .
@perryrose8843Күн бұрын
Wiring under the plug? Chafe point. Shoulda gone through it.
@BlindBatG34Күн бұрын
Holy poop, it really is a $175-200, plus shipping part. I thought you were joking.
@josephdavis85302 күн бұрын
I have changed a column in a 2002 Ford F150 . The column came with key . The truck will not start. On the dash board it has Theft wrote. Anyone know what is wrong and I need to do?
@josephtannenbaum86963 күн бұрын
So, a link to amazon for these batteries?
@courtneyanderson57173 күн бұрын
If it's running rough the first step is open side panel and turn drain screw on bottom of carb (shown at 10:40) to drain any possible water, debris. That solves my issue most of the time. The other 2 clear lines are the vents. Black lines are to fuel. I run these in the winter 40 or so times for 2-3 days and the fuel separates and the ethanol is at the bottom and is usually the problem.
@paintilludrop3 күн бұрын
Can you spray cleanerup onto coils. My ac is dripping, not real cold. Senior Low income, cannot repair on roof. Fl heat.
@wjpelka4 күн бұрын
If you were to rotate the battery 180 degrees, it would put the positive post further away from the frame. Then there would be less chance of sorting it to ground. However, the chassis is not grounded like a vehicle so there is difference in potential from frame to battery positive. That would also allow you to remove the 2x4. I had to use a shim for my battery on my DR Stump grinder when I ordered a wrong battery... I like my grader and have built my own wireless control that seems to work better than DR's. I had upgraded to their wireless package, but the system failed and I went back to original corded components, but built the wireless system...
@sweetjoesus5 күн бұрын
Like everyone else on here, thank you for this video! Back up and running in 20 minutes.
@murraymadness46747 күн бұрын
The regulator increases pressure when vaccum is low to boost the fuel for acceleration, so its working properly.
@Justthemow7 күн бұрын
Man I ran my def tank dry too so dry it fell off somewhere in Mexico
@BerryMcCaulkiner8597 күн бұрын
Pretty simple. Tank is bigger to spray more Def each tank
@jpasc6119 күн бұрын
Do you have pictures of where the 3rd function hoses connect to the loader valve ?
@aaronsrose8 күн бұрын
Not at the moment. It was pretty straight forward to hook up. Worst part was finding the correct Korean fittings and getting the adapter hoses made to make the connection into the tractor system.
@perryrose884310 күн бұрын
That may be a way to get better gas mileage to show the Feds. A new hose out into the grill or wheel well should get better temperature readings.
@joekirchner237411 күн бұрын
Nice acquisition!!!👍🏻 Be careful in wobbly bits California!
@aaronsrose10 күн бұрын
Thanks! Got my rubber boots for the feces on the sidewalks. 😆
@LOOKUP-ox1ld11 күн бұрын
Best video I've seen on this fix. Thanks. Direct to the point.
@stevenolden219511 күн бұрын
Great video, fixed my washer tonight thanks to this video!! You saved me hundreds of dollars thank you!!
@stevephillips899011 күн бұрын
What was the part #
@dallasbecker28612 күн бұрын
YOU DA MAN!!!! I couldn't figure out what was wrong and had not clue what that part was as it was just hanging free when I cleaned my filters. You just saved me from suffering in triple digit heat. THANK YOU!!!
@ericrodriguez409013 күн бұрын
Man, I installed this on my Eclipse and it sounded awesome for about a month. Now the bass sounds loose, almost like the diaphragm is rattling. It does sound good a super low volume. I'm getting rid of the blue LED adjustment today. Annoying AF. Any recommendations? I'm setting up gain, etc, exactly as you did right now.
@aaronsrose11 күн бұрын
Interesting. So far it's still running well even though I abuse it to the point of overheating playing Crowbar and Down frequently. lol. Is it solidly screwed to the floor? That made a shocking difference in quality of sound and dB for mine. If that's good and the connections are all good, it may be a defect. Thanks!
@chandrawallace74513 күн бұрын
Dang, that’s a beautiful TJ !! Of course I might be a little biased.
@hughbialecki178913 күн бұрын
Well done, thanks ! Two of my bakflip tracks have broken off. Jumping in on the repair.
@BlindBatG3413 күн бұрын
Getting good parts today is a struggle.
@jakemason943613 күн бұрын
Nice acquisition Aaron. What is the stock thermo temp rating?
@aaronsrose11 күн бұрын
OEM rating is 195F. I've got an OEM Mopar stat on the way and if that doesn't keep it under 200, I'm going to put a 180 in it. Nice thing about this older stuff is they aren't so sensitive to running a little cooler than stock. Thanks!
@mr.impossible342813 күн бұрын
Mine is leaking from the bottom since you’ve fixed it has it leaked from the bottom?
@aaronsrose11 күн бұрын
Never leaked from the bottom after this repair. The rad failed, but that was age related. Thanks!
@perryrose884313 күн бұрын
You can test the old one and new one in a pan of hot water and a thermometer.
@perryrose884313 күн бұрын
Back when the emissions crap started, mid to late '60's, Chrysler went to high temp thermostats. They may be purposely mislabeling temps.
@perryrose884313 күн бұрын
The "001 and the "04 Dodge 2500's both have a rattling throwout bearing. Dodge and independent mechanics have told me that is not a problem.
@Lane-jq3ed13 күн бұрын
Great looking ride, and the 4.0 has always been bulletproof for me👍🏻
@blazenvipers13 күн бұрын
I had to buy a new battery for my John Deere mower because the old one tested bad and was 5 years old. After connecting the new battery, I put a new one of these tenders on it. It immediately went to "solid red". Should the new battery really need charging? I use the battery cable claps to connect it. Thank you
@gazzilioneardad14 күн бұрын
I "re-calibrated" mine by performing some weight reduction....
@snakerog15 күн бұрын
Does the bulb have to work for the zapper grid to work? I am asking because Mine completely stopped working. I took out the bulb which came apart from being so old and tried to get the zapper grid to zap by touching inner and outer grid with a screwdriver, but nothing happened. So I am wondering does it have to have a functioning bulb for the zapper part to work? I don't want to buy a new bulb for it if the zapper part is not going to work.
@aaronsrose11 күн бұрын
I believe the bulb is part of the actual zapping circuit so if that isn't right, nothing else can function. Thanks!
@charlesbullee721515 күн бұрын
I had DEF recall they told me they changed the def pump. Now I’m wondering did they.
@jameskeen806316 күн бұрын
Had steering link recalled, they welded the adj. sleeve, shouldn't weld on steering parts. Did nothing for ABS problems I have had for 2+ years. Done with dealer .
@daviddavis248317 күн бұрын
Fuel pump relay it's under bed where spare tire gors
@biteme785717 күн бұрын
6.58 whats that part just befre the one you de assembled called ?
@cb7pwn17 күн бұрын
You're over inflating and need an alignment.... Don't shit on a company because of your ignorance
@daleyanke373918 күн бұрын
Ur kicker was right in the way when u drilled hole for oil pump im getting ready to drill myself could u show what hole u used in the guide
@fiveowaf45418 күн бұрын
I got a further letter today on the recall 67A. It discusses the extended warranty, but in the context of it covering if a check engine light comes on after having the recall modification done. Given the accounts of people having a check engine light issue that was difficult to resolve after the recall, it doesn't fill me with confidence that Stellantis are now admitting this could be a problem.
@dcarden303119 күн бұрын
They make great scca cars not to many cars fast and or cheaper in the class front wheel drive. Dont take much to make them handle and parts are cheap
@adamjohnson150219 күн бұрын
I seen nothing. Thanks
@chrisk543319 күн бұрын
RIP my 2014 diesel Jeep after its recall flash. Never again!!!
@sob3po19 күн бұрын
If you have concerns about tire wear, take it to a certified trailer service shop. Don't do this yourself........ And inspect your tires every trip and replace them before you have a failure.
@virginiaperez920820 күн бұрын
You did a great job showing us thank you
@leskeegan903323 күн бұрын
You picked a fine product using the Amsoil Lubricants
@twistedjeeper126 күн бұрын
That tractor with loader wet weight is 3350 lbs. I doubt the finish mower weighs 2500.
@DavidFury050527 күн бұрын
Thanks for the video, after watching it was able to change the drive belt in about 10 mins thanks your video helped heaps, and yep the hardest part was putting the spring back on.
@ronkimmel242728 күн бұрын
Thanks. Lead me to the cruise control switch👍
@Yielar128 күн бұрын
Came to watch what you used to insert the wires into the rv style receptacle and you did that part off camera 😂
Пікірлер
Great video!! Question can that solenoid by the shifter gears for park prevent the truck from starting? I have change the solenoid against the firewall under the hood with a new starter & now I’m using a screwdriver to start it with the same solenoid on the firewall!! SomeXs it would start & someXs it won’t then I would have to use the screwdriver..
I don't think the column would do it, but the neutral safety switch on the trans might
Thanks Bud..
To avoid damage S&S tell’s you in the manual to remove the pushrods in the first .
Wiring under the plug? Chafe point. Shoulda gone through it.
Holy poop, it really is a $175-200, plus shipping part. I thought you were joking.
I have changed a column in a 2002 Ford F150 . The column came with key . The truck will not start. On the dash board it has Theft wrote. Anyone know what is wrong and I need to do?
So, a link to amazon for these batteries?
If it's running rough the first step is open side panel and turn drain screw on bottom of carb (shown at 10:40) to drain any possible water, debris. That solves my issue most of the time. The other 2 clear lines are the vents. Black lines are to fuel. I run these in the winter 40 or so times for 2-3 days and the fuel separates and the ethanol is at the bottom and is usually the problem.
Can you spray cleanerup onto coils. My ac is dripping, not real cold. Senior Low income, cannot repair on roof. Fl heat.
If you were to rotate the battery 180 degrees, it would put the positive post further away from the frame. Then there would be less chance of sorting it to ground. However, the chassis is not grounded like a vehicle so there is difference in potential from frame to battery positive. That would also allow you to remove the 2x4. I had to use a shim for my battery on my DR Stump grinder when I ordered a wrong battery... I like my grader and have built my own wireless control that seems to work better than DR's. I had upgraded to their wireless package, but the system failed and I went back to original corded components, but built the wireless system...
Like everyone else on here, thank you for this video! Back up and running in 20 minutes.
The regulator increases pressure when vaccum is low to boost the fuel for acceleration, so its working properly.
Man I ran my def tank dry too so dry it fell off somewhere in Mexico
Pretty simple. Tank is bigger to spray more Def each tank
Do you have pictures of where the 3rd function hoses connect to the loader valve ?
Not at the moment. It was pretty straight forward to hook up. Worst part was finding the correct Korean fittings and getting the adapter hoses made to make the connection into the tractor system.
That may be a way to get better gas mileage to show the Feds. A new hose out into the grill or wheel well should get better temperature readings.
Nice acquisition!!!👍🏻 Be careful in wobbly bits California!
Thanks! Got my rubber boots for the feces on the sidewalks. 😆
Best video I've seen on this fix. Thanks. Direct to the point.
Great video, fixed my washer tonight thanks to this video!! You saved me hundreds of dollars thank you!!
What was the part #
YOU DA MAN!!!! I couldn't figure out what was wrong and had not clue what that part was as it was just hanging free when I cleaned my filters. You just saved me from suffering in triple digit heat. THANK YOU!!!
Man, I installed this on my Eclipse and it sounded awesome for about a month. Now the bass sounds loose, almost like the diaphragm is rattling. It does sound good a super low volume. I'm getting rid of the blue LED adjustment today. Annoying AF. Any recommendations? I'm setting up gain, etc, exactly as you did right now.
Interesting. So far it's still running well even though I abuse it to the point of overheating playing Crowbar and Down frequently. lol. Is it solidly screwed to the floor? That made a shocking difference in quality of sound and dB for mine. If that's good and the connections are all good, it may be a defect. Thanks!
Dang, that’s a beautiful TJ !! Of course I might be a little biased.
Well done, thanks ! Two of my bakflip tracks have broken off. Jumping in on the repair.
Getting good parts today is a struggle.
Nice acquisition Aaron. What is the stock thermo temp rating?
OEM rating is 195F. I've got an OEM Mopar stat on the way and if that doesn't keep it under 200, I'm going to put a 180 in it. Nice thing about this older stuff is they aren't so sensitive to running a little cooler than stock. Thanks!
Mine is leaking from the bottom since you’ve fixed it has it leaked from the bottom?
Never leaked from the bottom after this repair. The rad failed, but that was age related. Thanks!
You can test the old one and new one in a pan of hot water and a thermometer.
Back when the emissions crap started, mid to late '60's, Chrysler went to high temp thermostats. They may be purposely mislabeling temps.
The "001 and the "04 Dodge 2500's both have a rattling throwout bearing. Dodge and independent mechanics have told me that is not a problem.
Great looking ride, and the 4.0 has always been bulletproof for me👍🏻
I had to buy a new battery for my John Deere mower because the old one tested bad and was 5 years old. After connecting the new battery, I put a new one of these tenders on it. It immediately went to "solid red". Should the new battery really need charging? I use the battery cable claps to connect it. Thank you
I "re-calibrated" mine by performing some weight reduction....
Does the bulb have to work for the zapper grid to work? I am asking because Mine completely stopped working. I took out the bulb which came apart from being so old and tried to get the zapper grid to zap by touching inner and outer grid with a screwdriver, but nothing happened. So I am wondering does it have to have a functioning bulb for the zapper part to work? I don't want to buy a new bulb for it if the zapper part is not going to work.
I believe the bulb is part of the actual zapping circuit so if that isn't right, nothing else can function. Thanks!
I had DEF recall they told me they changed the def pump. Now I’m wondering did they.
Had steering link recalled, they welded the adj. sleeve, shouldn't weld on steering parts. Did nothing for ABS problems I have had for 2+ years. Done with dealer .
Fuel pump relay it's under bed where spare tire gors
6.58 whats that part just befre the one you de assembled called ?
You're over inflating and need an alignment.... Don't shit on a company because of your ignorance
Ur kicker was right in the way when u drilled hole for oil pump im getting ready to drill myself could u show what hole u used in the guide
I got a further letter today on the recall 67A. It discusses the extended warranty, but in the context of it covering if a check engine light comes on after having the recall modification done. Given the accounts of people having a check engine light issue that was difficult to resolve after the recall, it doesn't fill me with confidence that Stellantis are now admitting this could be a problem.
They make great scca cars not to many cars fast and or cheaper in the class front wheel drive. Dont take much to make them handle and parts are cheap
I seen nothing. Thanks
RIP my 2014 diesel Jeep after its recall flash. Never again!!!
If you have concerns about tire wear, take it to a certified trailer service shop. Don't do this yourself........ And inspect your tires every trip and replace them before you have a failure.
You did a great job showing us thank you
You picked a fine product using the Amsoil Lubricants
That tractor with loader wet weight is 3350 lbs. I doubt the finish mower weighs 2500.
Thanks for the video, after watching it was able to change the drive belt in about 10 mins thanks your video helped heaps, and yep the hardest part was putting the spring back on.
Thanks. Lead me to the cruise control switch👍
Came to watch what you used to insert the wires into the rv style receptacle and you did that part off camera 😂