Hi buddy! I just went to my garage at 5 a.m to check the Febi sport set (Made in Germany) that I bought for my 2013 Golf TDI: there was No play whatsoever...snug and solid like the OEM. Happy with my purchase: pricey, but high quality...I am doing the whole suspension on my MK : Koni Str.T struts & shocks, H&R springs, fEBI spring perch uppers, Febi & sachs struts and shocks mounts, Febi/Rein sport bump stops...the whole set!

Interesting video -- thanks for giving such a thorough investigation

Great Job Mr Sanders....Kudos from Montreal which has worse roads, because of 6 months/year snow....!Keep up the GREAT job! I have just subscribed and put a fat/big thumbs-up!

Very nice, helped me decide what to do about new bushings for the konis I have waiting. Might just stick with oem, lol.

Good video m8, a small tip would be very careful when working on the ground as small stones and grit can get stuck to the grease and end up in the bearing. Just put a bit of cardboard down and good to go. Good luck bud 😊👍👍

2014 VW GLI. Replaced front stock Fuchs setup with Bilstein B4 shocks (amazon), SKF bearing and Lemforder from FCP Euro. Had my non VW local guy install today. Also experiencing a knock/clunk in my front passenger side shock area. And all my dashlights are going off which looks like a bad connection/possible replacement of the wheel speed sensor after installing shocks. The hits keep coming but they won't get me down. Thanks for sharing your video. I should have used your drop test on my SKF/Lemforder setup before installing it.

last bush not lasted 5years think you just solved my problem all the very best of luck for future 😁

Thank you so much for this video! I think this is the same issue I'm having.

Makes sense after I replaced 3 sets of monroe fool strut assembly. Never again! Before I figured it out I replaced my whole front end... And then I find out they had this problem for a while now. Don't waste your time on full strut assembly. Or be ready to replace upper strut mount and bearings.

This is it! Thank you!!

Great Video. Thanks for the info !

@ispeedify

6 жыл бұрын

Riccardo Pelc-wesoly Your welcome!

Good find. And 3:10 that "pliers" looks like a screwdriver.😃

It's not the bearing slop, it is the design of the strut mount itself. Regardless, changing it out fixes the issue.

Dru I have knock on mk 5 tdi 170.It comes and goes .Was it like a rattle knock if you know what I mean.?Makes you replace the drop links .Ok for a few miles then comes back. Doesn't cure it? OBV

Nice video, so wats de position of de arrows?

im having this problem on a stock jetta thats old dealership said its becasue im missing a bellypan and need a new front end i think the shocks need replacing

Hi.what code do the OEM have?

Have similar noise with 2008 MK5 OEM's 145,000 miles - just old. Definitely need to replace.

@richardjohn7991

4 жыл бұрын

Scott were you getting like a rattle knock that went on and off??I mean if it was a cold or hot day??

My 2011 TDI makes a clunk on take off and sometimes during deceleration. I have stock everything, except the dog-bone mount (HPA). I'm wondering if both the bearing and the mount go bad, or if it's just one of the parts. I plan to buy OEM, but they sell them separately. That suggests that only one or the other goes bad. What's the likely culprit?

@Revedance2002

6 жыл бұрын

Did you end up solving or figuring out whether it was the dogbone or the Bushings for you?

hello, how did you get your digital cluster to mirror off of your phone but play audio through the oem radio?

Im having the same noise problem, but i have the oem bushings and strut mounts. i just installed eibach 1 inch lowering springs to the stock shock. I'll see if theres any play in the bushing, but also it looks like you got the strut off without removing the entire rotor and everything...which is what the instructions told me to do for my spring installation. How do you do this? THANKS!

@alyamoney

6 жыл бұрын

Bailey Graf did you do it lol

Makes me wonder about their motor mounts.

The Oem reference of the vehicle is the correct?

Out of curiosity, did 034 Motorsport ever contact you regarding this? I'm using their strut mounts on my MKV GTI and I get squeaks and creaks especially during the colder months.

@ethiopianeyes

Жыл бұрын

a good thing to do is spray some silicon lube between the bearing and housing rubber. helps a lot

Mate my VW Touran Coil springs of the front driver hand side jerks and make noise when turning my car left or right,do I need to change the whole shock absorber or it's a faulty strut bearing?

@ispeedify

6 жыл бұрын

sal k 🤔 Hard to say mate. I would double and triple check everything.

Great video! I’m having sort of a similar problem. A shop installed my VWR springs with new mounts and bearings but there is popping and banging noise from the driver’s side. There is play in the strut assembly as I can move it up and around a little bit by hand with the car jacked up and wheel off. The shop used a cheap (at least $ wise) OE style replacement but either installed the mount in the wrong direction or there is play between the mount and bearings like you demonstrated. I’m going with the mount and bearing clearance is too large. I am curious if your mounts in the video, to replace the 034’s, are VW branded or an OEM equivalent?

@JH-sc7cs

Жыл бұрын

How did you go?

I'm getting a clunk on the passenger side front all new setup and I think that might be my issue! It's been making me crazy!

@aleksandars88

3 жыл бұрын

If it doesn't mounted correctly it will make clicking sound. Narrows must bi towards front/rear of thr car. Mine was wrong mounted and had same problem

Has this continued to make no more knocking? Wife has a 2013 A3 that we have been having bad knocking and I thought it was the strut linkage as the small boot was split. Replaced it and the noise was gone for a few miles then came back. Now I kind of wonder if this is the problem. Mine is an ECS racing model that are black as well. Probably the same manuf that yours are just labeled different. It knocks bad when coasting on a bad road. If braking or accelerating the noise is almost gone which leads me to believe that it is some part that when it is under tension while braking or accel it causes enough tension to "snug" things up a bit but while coasting there is no tension and things are more loose.

@ispeedify

6 жыл бұрын

Sorry for the late reply here, but to answer your question the answer is yes, yes the problem is gone and has stayed gone with the new OEM bushings.

where did you get the oem's ? what is the brand? store name ? part number ?

I had near enough the same problem with new struts and aftermarket strut tops. First test drive was terrible, got home sprayed where I could with silicone spray and it still knocked, rattled, and squeaked.....the next morning all the noises were gone but had a bit of spring boinging from one side......can't stop it, I may try some spray grease into bearing ring.....

@jasonga

2 жыл бұрын

Update, rain today has made all the noises come back.......DONT BUY CHEAP SHIT FROM THE INTERNET, IF ITS CHEAP ITS CHEAP FOR A REASON.....

@JH-sc7cs

Жыл бұрын

​@jasonga did you fix it with genuine strut mounts ?

Non OEM parts are crap what a surprise, who'd have thought. This is ground breaking info.

dude I also live in Hawaii, on Oahu. yes our roads fucking suck. seems like the state is constantly working on them but they stay the same, or a year goes by and the road they fixed goes right back to shit. #jobsecurity but yeah man, I drive a 94' passat glx 2.8L VR6 with 262 cams, 3" intake and exhaust. running into some lean problems, but being an obd1 its hard to diagnose exactly the culprit of my problem. I also have a bunch of cracked vacuum lines that need to be replaced, but i've been thinking of deleting the SAI and EVAP systems. I run rough on cold start, and after 3k-4k RPM the CEL light comes on, but goes away after i release the throttle. you got any ideas as to what it could be? If you ever wanna link up and car cruise and take pics lmk! I live in town.

im getting the top mount clunking noise with oem bushes and h&r coilovers

@nickbellais1192

3 жыл бұрын

Replace the entire strut mount assembly....mount, bushing, bearing, pinch bolt, and stretch bolts. Should go away after that

Moral of this story: Buy OEM parts!!!

We’re just gonna ignore the fact that during the loopty doo he was driving a manual barefoot? 😂

10:03 I disagree; I invite you to drive from Brooklyn to Queens of NYC and tell me again if your roads are shit compared to ours. I've already spend a little over $2k on wheels/tires due to potholes tearing my car up -- and the city has a way of not paying.

@PHxNiteRider

4 жыл бұрын

So true its horrible...

VW oe parts are the best parts for your vw. Thats why they cost more.

Is this the same setup as a mk5 GTI?

@ispeedify

6 жыл бұрын

Ivan Vega I believe it is.🤙🏾

It’s ur transmission mount that’s gone…not the strut. It’s clunking

Sorry but where is the noise? The title suppose to be demostrate what is the noise.

thats what worn out bearing do is what the 034 is doing. bad QC

You do know 034 is Chinese stuff