NEW lift kit video is up! Check it out kzread.info/dash/bejne/lomVuc5vdNHQidI.htmlsi=ljpxQH4MJ3MH1JxH For discounts on all Torch Off Road parts use www.torchoffroad.com/truckandroll

Awesome video. Very well explained and thorough.

Hey man you did a good job!! I'm going to do my truck like that ..👏

I got the 3", just finished the driver side, fender is at 39" but should go up more when I get new tires, 285/75/r16s

Looks great.

@truckandroll989

Жыл бұрын

Much appreciated!

I like it look good thank you buddy

Bro u did amazing

@truckandroll989

6 ай бұрын

Thanks I really appreciate that! Plenty more videos on this truck from stereo to full exhaust! Loved this truck :)

Maybe your truck is a little different but most of the time the adjusting screws for the torsion bars should be close to the same measurement from one side to the other....

I installed two inch keys to the torsion bars on my 98 Silverado ext cab. I also had to compensate the rear with 2 inch blocks. I think I had to crank the keys up to 3 inch to level it out. I can't remember. It was about 4 yrs ago I did it. It drives fine but stiffer. It hops over speed bumps unless you really creep it over. As far as being level side to side, one corner is like a 1/4 inch different than the other 3. I just called it good. You can't tell. 2 inch lift looks better but I plan to add another 2 inch, making it 4 inch lift. I also installed air bags to the rear for towing.

Thank you for this helpful video! I've got a '98 Tahoe I'd like to lift 2" using the 2" blocks rear, and adjusting the keys in front, like you did. Two questions: 1. When you hit a pothole or bump hard, does the truck feel wobbly? 2. How's the angle of your front axle shafts after the lift? Thanks much!

@truckandroll989

4 ай бұрын

Truck doesnt feel wobbly at all over bumps, perhaps marginally stiffer but not wobbly. I didnt notice an issue with the axle shafts. The CV joint can take quite a bit of misalignment. Any higher and you may want to consider the modified upper control arms which Torch Off Road sells. Dont forget you get discounts using my code (link in description) for anything purchased off their website I think the 2” lift is really the happy medium here. I think you will like it!

@wpdv

4 ай бұрын

@@truckandroll989Awesome! Will do! Thank you.

Got my lift on my definitely is stiffer but I have old shocks hoping that the skyjackers make little smoother ride

@WhiteColonizer

Жыл бұрын

Any update?

@bigcountry4588

Жыл бұрын

​@@WhiteColonizerget 2-4 upper control arms

@jessesarrett9477

Ай бұрын

Does that help with clearance on the upper bump stops? Im just trying to figure out what to do next on trying to make it smoother and not hit the stops​@@bigcountry4588

I have a question about the sky jacker schocks my bushings seem to tight to fit the metal bracket for the two rear bolts did you melt yours down ? Thank you kinda following your setup 👍

@truckandroll989

Жыл бұрын

So they are certainly a bit of a pain to press in you are correct. Here are a few tips: 1. Use some sort of lubricant. I have found for rubber on metal that interior cleaners work well (i.e. armor all, lucas, etc.). Even windex works in a pinch. 2. You can always try to toss the bushings in the freezer overnight and leave the shocks out in the sun. Sometimes a little bit of thermal growth/shrinkage goes a long way Take your time they will go in. Lubing them up really helps :)

@mikeydejon2148

Жыл бұрын

Thanks I appreciate the input it just seemed like bushing were to big but I’ll throw in freezer then coat them in wd 40 tmo👍

@mikeydejon2148

Жыл бұрын

Everything’s done thanks for input I only swore 50 times getting bushings in😤👍😂 I will be starting to do some obs videos soon👍

I went to the site to get the same kit I see the torsion bar keys for a 94 model Chevy but I don’t see the shock kit or the rear leveling kit for anything but for a 99-07 Chevy. Will the 99-07 kit work on a 94

@truckandroll989

7 ай бұрын

Best bet would be to call or email them. They are very responsive to both and helped me find something I didn’t know they offered. When its time to order use the link torchoffroad.com/truckandroll and you should get a discount at checkout :)

All the torsion keys are is ford torsion keys that chevy uses for a cheap lift but the bad part is that it puts the ball joints in a bind if taken to much and stiffins the ride also

@truckandroll989

10 ай бұрын

Yea its a balancing act for sure. I went up 2” instead of the full 3” that the keys will allow. Similarly i installed larger shocks to allow for the increased travel. You are right though modified UCAs or new ball joints are a good call for longevity sake, especially if lifting 3” +

@bananasdildo

5 ай бұрын

did you buy the 3" keys or 2" keys?

@truckandroll989

5 ай бұрын

@bananasdildo ordered the kit that allowed 1-3” of travel and shot for 2” by the spacers I selected in the rear. I believe keys are one size to accommodate various lifts depending on how you set them.

Hey what size tires are on that truck? Looking at doing this and trying to find some tires to compare it to

@truckandroll989

5 ай бұрын

32x11.5x15 BFG All Terrain K02

You don't have sway bars...my Yukon does. I'm looking for the 2-3" lift. Do you happen to know if i need to extend the sway links?

@truckandroll989

Жыл бұрын

I have sway a sway bar in the front and it was fine

@worldwideaudio1705

Жыл бұрын

@@truckandroll989 awesome! Thanks!!

Great video! What size tires are you running?

@truckandroll989

Жыл бұрын

32x11.5x15 BFG All Terrain K02

@CelebrityStuntman

Жыл бұрын

@@truckandroll989 They look great! Thanks for your reply.

@truckandroll989

Жыл бұрын

@@CelebrityStuntman thank YOU for watching! I really do love the k02s. Fantastic in our utah winters having to drive up canyon roads

Curious why your tow hooks are open down instead of to the outside? Just aesthetics?

@truckandroll989

Жыл бұрын

I think they are not the original tow hooks for the truck. They are turned 90 deg in the wrong direction but thats how they bolt up. If i could snag the correct ones Id swap them

@SlicksOutdoors

Жыл бұрын

@@truckandroll989 they look good, I was just curious if you heated and turned them or if you bought it that way. Thank you so much for the tutorial, I’m about to put 2” keys on my ‘98 model.

Hey I’m looking into this lift kit, do you think someone could run 35s with 3 inch lift?

@truckandroll989

Жыл бұрын

I had plenty of room granted i went with the 2” lift and am on a ~33” tire but i bet you could. Backspacing and width up front would play a key factor

Just did the Torch 2-3" leveling kit on a 99 Suburban, the problem I am having is that my new torsion keys seem like they hang from the bottom more than yours(from what I saw in the video). This is causing the UCAs to hit the droop stops I have the keys resting on the saddles as far down as they can go. I have tried various positions and swapping the keys side to side but it hasn't fixed it. I'm starting to wonder if I need new torsion bars. I ran into the stuck bar issue too on the passenger side, even tried a come along to pull the bar forward (didn't work). I ended up moving the brace back as you mentioned. Once the brace and key was off I was able to wiggle the bar around at that end and loosen it up to slide it forward. I needed it loose for future LCA bushings and ball joint install.

@truckandroll989

9 ай бұрын

Hmm. I think you are on the right track trying to adjust the key location by maybe 1. Are you checking side to side height with the suspension loaded and sitting on the ground. Do you have UCA issues says at 2” of height (higher than before). Mine required some fine tuning to get the truck level

@4theloot638

9 ай бұрын

@@truckandroll989 I attempted to adjust the key by one flat but it either hits the top inside of the cross member or droops more. The key sits on the saddle with tension on the tip of the bolt just touching its indent. The UCA is against the droop stop even when loaded with the keys in. When I installed them, I had the same conditions as yours with the wheels off and the frame on jack stands. I have 3 1/2" inches of lift compared to my stock height with no room to go down.

@truckandroll989

9 ай бұрын

@@4theloot638 sounds like have them droop and then adjust upwards? I doubt the torsion keys are totally shot but could be wrong. Perhaps Torch can help you out?

@4theloot638

9 ай бұрын

@@truckandroll989 Thank you for the help, I have shot them a message to see.

@4theloot638

8 ай бұрын

@@truckandroll989 Torch got me a new set of keys but, it is still the same issue. I ended up having to buy a set of Rough Country 2" keys. It seems to be sitting level and has a gap below the upper control arm now.

Looks good. What size tire?

@truckandroll989

Жыл бұрын

They are a 32 x 10.5 x 15 i believe. BFG All Terrain K02

Whats the part number on your skyjacker shocks?

@truckandroll989

Жыл бұрын

H7083 and H7081

Can you do som dragy videos with the mustang 60-130?

@truckandroll989

Жыл бұрын

I need to get a draggy and weather above 20 lol but id like to

Any issues with the stock upper control arms or getting an alignment?

@truckandroll989

Жыл бұрын

No, not that I’m aware of. The alignment went fine and it seems to drive OK

@yep.yep.yep.000

Жыл бұрын

Cool man, I read alot of reviews on Amazon. They indicated that even with the torsion bolts backed way out. Stock upper control arms were hitting bump stops and un able to align. I wasn't sure it fake hate reviews or truth. Either way I ordered the exact equipment in your video and I'll try my luck. I have a 1996 chevrolet suburban k1500.

@truckandroll989

Жыл бұрын

@@yep.yep.yep.000 sweet hopefully you took advantage of the discount code ;)

@yep.yep.yep.000

Жыл бұрын

Aw shit I forgot 😮 my bad

@extraziadeh

9 ай бұрын

Any update on this? I wanna run this kit but was also thinking about UCAs smacking the bump stop

I bought a truck (94 chevy) with 35s on it and it has a body lift kit. Also rhe front torsion bars are cranked to the max. The ride is horrible. I want to lift the truck up more just to lower the front end down to have a softer ride.i know i could just put smaller tires on it but i want it up the same if not a little higher than it is now

@truckandroll989

7 ай бұрын

In my opinion any time the torsion bars are cranked front stock you will change height but also impact ride quality. So if you need the clearance for 35s Id look into ways to minimize maxing out the torsion key cranking and that would help ride quality and likely increase longevity of other suspension components. For me I had like 32” tall tires so it wasnt a huge issue to add 2” up front. However there will always be some amount of tradeoff.

Do they turn when you take them out the torsion bars ?

@truckandroll989

Жыл бұрын

The only way for the torsion bars to turn would be to remove them from both the keys and the lower control arms. If yours are like mine, and are stuck in the control arms, they cannot turn.

@mikeydejon2148

Жыл бұрын

Okay I appreciate your patience thanks bud 👍

Does anyone know where to find a complete wire harness for this truck ?

@SpeeeedyG

5 ай бұрын

LMC

What size tire are you running with lift kit?

@truckandroll989

11 ай бұрын

Same as before the lift. They are a BFG k02 and measure just under 33”

Do you have any probs with hitting the bump stops more after the lift

@truckandroll989

8 ай бұрын

I did not. It maybe road a tiny bit rougher but that’s not uncommon when you lift it from the keys. I also only went with the 2” lift so it certainly wasnt maxed out in its travel.

@04JALD

8 ай бұрын

@truckandroll989 ok cool. I am not wanting to much of a lift but I saw others talk about the bump stops too. Good job on your video. Thank u.

What was the final height at 26:14 and what size tires are you running I'm chasing after this look on my truck thank you.

@truckandroll989

4 ай бұрын

I want to say right around 35” maybe a tiny bit taller. Tires were a 32.5x12.5R15 (BFG K02)

@HartingFarms

4 ай бұрын

@@truckandroll989 I'm assuming a 3" lift and 33s on my rims and BFGs would give me what I'm chasing. What do you think?

@truckandroll989

4 ай бұрын

@@HartingFarms if you are going for a similar look to me then yes 💯 I think it would look great!

@HartingFarms

4 ай бұрын

@@truckandroll989 Alright thank you I appreciate your time

How is the front suspension holding up?

@truckandroll989

9 ай бұрын

No issues!

Is that n Avs bug guard ? I couldn’t get my hood to close correctly any tips ?

@truckandroll989

Жыл бұрын

To be honest Ill have to check. It was on the truck when i got it and seems to close just just fine. That being said it is cracked in the center as has been since I got the truck

@mikeydejon2148

Жыл бұрын

Thanks for your discount code I got mine what shocks r u running ?

@truckandroll989

Жыл бұрын

@@mikeydejon2148 Excellent! Glad it worked out. I went with Skyjackers. The part numbers are H7083 and H7081

@mikeydejon2148

Жыл бұрын

Thanks!

Are the new shocks that you installed stock length?

@truckandroll989

Жыл бұрын

Nope purchased longer then stock on purpose to account for lift

@yep.yep.yep.000

Жыл бұрын

I was asking because supposedly some stock shocks have a bit of extra travel.

@truckandroll989

Жыл бұрын

@@yep.yep.yep.000 yea you definitely want to get a longer shock IF you are lifting and vice versa if lowering. My old shocks were in OK shape but i was worried id be extending them beyond their useable range

Did you have to get different control arms or did the stock ones run just fine

@truckandroll989

4 ай бұрын

I did not have any issues with the stock control arms, but I didn’t go as high as I could have in the front so if you were maxing out the torsion keys, it might not be a bad idea to get new control arms too

@bossman147

4 ай бұрын

@@truckandroll989 I plan on doing something similar to what you did by adding in the 2 inch blocks then just leveling out the front with the rear

@truckandroll989

4 ай бұрын

@@bossman147 yea i think it gave it a tough look without going overboard. Use the link in the subscription and you get a discount on your order 😎

@truckandroll989

4 ай бұрын

HTTPS://TORCHOFFROAD.COM/TRUCKANDROLL

@bossman147

4 ай бұрын

@@truckandroll989 thanks for helping me out after making the video almost a year ago

Bedliner u used?

@truckandroll989

3 ай бұрын

I’m not sure it was on it when I bought the truck maybe rhino lining

Why not just crank the stock torsion bars? maybe I missed that part.

@truckandroll989

7 ай бұрын

So the aftermarket keys are clocked differently. You dont have to crank the new keys as far for the same lift. Its possible you could run out of of adjustment.

Angle grinder. Cut the rear u-bolts off. You get new ones anyway.

@truckandroll989

9 ай бұрын

Very good call. Was my first time playing with those stupid things but you are 100% right

How is the front end holding up a year later?

@truckandroll989

4 ай бұрын

Truck has been rock solid :).

@JustSomeGuy38790

4 ай бұрын

@@truckandroll989 ok thanks!

What brand are the rims???

@truckandroll989

Жыл бұрын

Not sure sorry ill have to check later