I’m buying this just bc of the tutorial video. So good!

Any change to support BB Full frame 6k? I got 2 motors and wanted to use one for iris, can I use the zoom lever on the wheel? also I want to add my irix 30 mm lens can you do a video for user lens? thx

Is there a video going into further about connect camera control for fx3? I followed everything to a tea, but it's still not connecting to my fx3. I updated all the firmwares camera and the nano

When I map in my user lens it does not show the focal length of the chosen lens is there an option to show the iris stops and zoom distance on the main page or can you add a fourth page to display all three? The torque doesn’t seem to change when set to the lowest option the gears often jump of the lens which effects the user’s mapped point and I have to hold the motor in place. I also find after auto calibration you have rotate the focus wheel from infinity to minimum focal twice before unit shows correct focus points.

At 22:05 you talk about colors and motor numbers. What is the correspondence? How do you know which color 'motor 1' corresponds to?

I liked that on the original nano wheel you could set A/B with the hardware buttons - but on the Nano 2 you can only set marks with the FUNC button - you have to look at the screen and hold the A/B button onscreen. Is there any way to make the FUNC button operate as A/B marker? If not please can we have this in a future update as an option?

Hi. Nice Overview. Is it possible to run the motor with the side handle standalone or do I lack functionality when running without the main wheel?

@Nellkay

2 ай бұрын

I have the motor with the handle, it works fine. You just have to make sure to attach the handle from the top as the side nato rails are not for mounting it to anywhere

What does the rocker range parameter change? It's hard to tell, I've played with the setting and not much changes

Can the REC button be used to initial recording on the Panasonic S1H via that camera's remote port? I have the Tilta cable labeled "For Handle/Motor" on one end (USB-C), and "GH/S series R/S" on the other (3.5mm TRS). BTW, I am able to trigger recording on my GH5 and S1H with the old Tilta powered control handle, via a micro USB cable from the original Nano 1 motor to the cameras' remote port. So, that means the remote port on these cameras is working. I just can't get it to work with the Nano 2 control handle. I have the same problem with the Advance Focus Grip.

Is there a semless way to switch between the handle and the fosu wheel ? I would like to have the gripp attached to the camera and the wheel atached to the soulder rig. and to switch between those two on the fly when mounting the camera to a shoulder rig.

I have a question, Focus Wheel can also be used on Sony lenses that have PZ? I would like to control the PZ function, without having to connect it to the Ronin, is it possible to work?

Just got this and love it so far! Only thing not working so far is the Bluetooth. I’m trying to connect to a BMCP 6K and it sees the camera, but won’t actually connect when I press the frequency. Any suggestions?

@TILTA

7 ай бұрын

shoot our support team an email at support@tilta.com!

How can I configure to see the focus distance of any manual lens? I only see that it is possible with the lenses that are saved on the list.

Is there a way to use the Nucleus M controller for this motor and Nano at the same time? I mean one for focus and one for iris

@TILTA

9 ай бұрын

Yes that would work.

can I use the nano ii wheel on camera for local control and the nuclear M wheel with my focus puller, easily switching back and forth to control focus?

@leonpowell1044

6 ай бұрын

That has only recently be made possible on a $30000 systems I doubt Tilta has a manual override on the nano II hence no answer

what accessory is attached to the hand wheel controller on the cage?

@TNerdProduction

4 ай бұрын

I want to know it to ❤

@tilta: Do you plan to add support for Nikon cameras to the Nano-II? It would be quite handy if that’s the case, appreciate your feedback.

@TILTA

8 ай бұрын

We do not have a definitive date yet but we are trying our best to push it now.

@bsc001

8 ай бұрын

Thank you for feedback. If you need a beta-tester, I have both Z6II and z9 available for testing. @@TILTA

will it work with the BMCC 6K FF as well? please say yes!

EZ Mode doesn’t seem to connect the Nano 2 handle to the tilta receiver. Any tips on what to do?

I just unpacked my new Nano II and I can't get camera control to work on any of my cameras (BMPCC 4K, 6K Pro, and 6K G2). I'm using Blackmagic's latest firmware, 8.6 Public Beta on all 3, and I've updated the Nano II firmware. Is this incompatible? I also tried using it via the Bluetooth+ App, same thing.

When will the Nano II motor be compatible with older Tilta Side Focus Handles?

@TILTA

7 ай бұрын

We will be releasing a cable for Nano II to use with advanced side focus handle soon.

@optical-sound

7 ай бұрын

@@TILTA Great news, thanks! A bit unsure why a regular USB-C with a firmware upgrade wouldn't cut it, but any way super glad to hear I can still use my handle. Thanks again for the update

@optical-sound

6 ай бұрын

@@TILTA I noticed in the Dec 23 firmware update that the Nano 2 motor now supports Nucleus M side handles. Is this also the case for advanced side handles? Thanks for the update 🙏

@MarcusWitte

3 ай бұрын

Looking forward! :D@@TILTA

Seems like FX3 support is only through USB right now? Hope there's a bluetooth option in a future update. When using external batteries, I prefer to use USB over a dummy battery to reduce the chance of the camera losing power.

@TILTA

8 ай бұрын

As of now the only communication is through usb-c. This is something we are currently trying to push (the wireless functionality) but there may be some limitations when it comes to Sony's protocol. More info about this coming soon.

what are the currents supports for FX3 and FX6?

On setting marks, how do you change the speed of the wheel if you’re trying to do a FAST focus throw. I noticed when I set the A/B marks and start turning the wheel it’s very slow and you need to turn the wheel a lot to actually finish the focus range..I’m talking about a fast 1 second dramatic focus throw

@Mekchanoid

5 ай бұрын

I'd like to know too! Frankly that sounds too sophisticated for this, especially at a time when much of the core pre-release functionality is still buggy. What voltage are you putting into it? That might be one reason why it's slow. My experience is that regardless of the speed of your hand movement, beyond certain speeds the motor starts to lag.

@Scifictus

Ай бұрын

Yes - go into Settings - Rocker Speed - then 'Range' to adjust how quickly the focus throw will go between A and B - but the wheel must be in DF mode for this to work.

@philliptamez

Ай бұрын

@@Scifictus awesome thank you! Does your unit ever have a problem when calibrating and when it’s supposed to go into the opposite direction after finishing one direction, it keeps on going and scraping the gears? Mine seems to do this a lot

Nucleus M handle still doesn’t work with N2 motor. When will there be an update?

Do will open the api communication protocol, will be nice to develop a compatible UEngine addon without the need of reverse engineering your protocol like we did with previous version.🤔

Hi, I'm interested in this product for one shot in particular, where I would need a very slow, controlled and fluid zoom-out. Is it possible with this device to change the speed of the zoom rocker ?

@DadDoesOutdoors

4 ай бұрын

Yes, within ‘Multiplier’ menu

Hi there. It says you can use the new dji motor to focus from the nano wheel. But I can not see how to connect it. I bought the new focus pro motor - nowhere I can find how to connect it. The wheel has a dji flip even .. but not a description how to pair

Have you got a part number for the right angle rosette adapter for the control handle? It looks slightly different to the Nucleus M. If it is, I hope it’s a little cheaper than the Nucleus M adapters!

@TILTA

7 ай бұрын

Yes, here is the SKU: TA-RRA-1420

@FrazerBoorman

7 ай бұрын

@@TILTA I have bought one already and find that it wiggles loose. The locating pins aren’t snug so the handle can wriggle side to side, eventually loosening the handscrew… Have you seen this before?

i get motor error often to frequently, and i wish you would of included a usb wall wart, just so you could get immediately working, cause it don't like alot of power stuff. just got it, i have it setup for zoom, ive read all that there is, watching videos, updated firmware. ill call/email if problems continue.

when the tilta nano 2 will be able to control and start rec on the sony a7 iv ? Is the firmware update release soon ? Thx

@TILTA

8 ай бұрын

We are currently working towards to make this happen. More info coming soon on the next firmware update.

What happened to the handle? Will it still be released or is it discontinued? And if it will be released, what's the cost?

@taylormacbrown

8 ай бұрын

Definitely want to know the answer to this

@SliceOfFilm

7 ай бұрын

@@taylormacbrown It is available, don't think there's any reviews yet.

what is your F adapt used?

Can this be used with the DJI LIdar to auto focus a manual lens?

@TILTA

9 ай бұрын

Unfortunately, it is not actived yet.

I want to see a better view of how the control handle is attached

@sachathomasvideophoto1199

6 ай бұрын

Same here.

How do you pair hand wheel with dji rs3 pro motor?

Is the only way to turn off the motor by disconnecting the cable?

The focus ring on my lens has a long travel distance (270 degree), and when I turn the wheel to max or minimum, it doesn't make the lens to infinity or minimum focus. What should I do?

@ianmartin2924

Ай бұрын

Manual calibration

Did u guys forget to put in a charging status indicator? When it is plugged in i cant find anyway to see the charge status. The only way to check is to unplug the item and check the battery icon to guess if its full or not, its so small its hard to tell. Can u guys add a firmware that puts a charging status on the screen when its off and plugged in

with FX3 Trying to connect via USB-C. Only OUT 2 works. When I change to OUT 1 PC Control is unavailable. WB doesn't work. ISO, SHUTTER & APUTURE work. Would be great to have PD to camera from battery through the motor. Otherwise it's not that useful with FX3. Also trying to connect with Nucleus M left handle - not supported yet. It seems like I bought too early.

@ok-fd7gq

8 ай бұрын

too late to return

when will be release date for the handle ?

@TILTA

8 ай бұрын

There has been a slight delay but it is looking like early November. Please keep your eyes peeled on our socials and website for more info regarding the official launch date.

anyone know how to control a7s3 with the wheel through bluetooth or wifi? I cannot get it to work. Pairing works fine but ctonrols and info never go thru

I don't see any charging indicator when I attempt to recharge the internal battery of the Nano II control wheel. How do I know if it is charging?

@TILTA

6 ай бұрын

We are working on showing battery status through the blue LED indicator above the screen. This feature has not been optimized yet but we will be looking to do so in the next firmware update. It should take about 2-4 hours for a full charge depending on the source so I would go by that until we implement a better solution.

@streetlife20

6 ай бұрын

Was wondering about that too lol!

Nick. I have tried to contact Tilta in Burbank with some questions to no avail. How can I get in touch with someone? I have a fair amount of questions regarding the II, and the just released firmware (Dec 2023). Like, what happened to the mulitplier? But also some other general questions - can you calibrate the knob for a lens without stops? What exact adjustments are supported for the FX3? Do I have to recalibrate a lens every time I use it, or does the Nano store info that can be recalled? Why does the screen freeze up some times? I've got a few more. Can I get any support? Thank you! I think I'm going to love this, but there is a learning curve for sure. Also, I can't seem to really enter info at all on the lens page. What's the voltage out of the second USBC motor port? It needs to be 9 volts for the FX3. Your motors will work between 3V and 17V, so a 5 volt USB A will suffice, but I don't think that's enough to jump to the FX3 and provide power from the second port. Just lots of questions.

@TILTA

6 ай бұрын

please email support@tilta.com and someone from our support team should reach back out to you

I like the fact that you went into such detail in the video, lots of work to create the video I'm sure. I needed to review the video several times to try and setup the unit I purchased and have a few thoughts. For future videos please consider not using such an annoying sound effect in between EVERY chapter. Also, regarding the voice over, please complete the sentence with full voice projection, the drop off at the end of each sentence sounds mumbled and garbled. Nit-picky yes....But got very annoying when trying to pay close attention. I feel for the editor of this piece. I ended up returning my Nano II. The product had issues, most of been a lemon. Spent a few hours trying to get it work but no luck.

Ex to get the mirage motor working... But how to use both the mirage motor as motor 1 and the nano ii motor in motor 3 for example?

@TILTA

9 ай бұрын

Click mirage button for 4 times and you could select the motor number for mirage and then you could change the color for nano II motor to make it motor 3.

@Shutaru1985

9 ай бұрын

@@TILTA i'll try it out and get back to you guys. My mirage motor, when nano ii is in manual mode, works fine but since in manual only 1 Chan can BE active at any given time, even when i have the nano ii engine lets say, in Blue color, it does nothing on the front rocket/switch

Is there any reason by when trying to calibrate the zoom manually using the rocker that the motor goes to full strength and rips pass the hard stop causing it jump off the ring so you can never achieve a proper calibration. When I using auto it only spins for a short time and never reaches the hard stops. So Im stuck with a zoom that either get bumpy at the end of the hard stops, causing the lens to move or a zoom that never reaches the end points. Please can we have some more detail information on the operation of the unit. Any new of any firmware updates? as it still feels very buggy, the lens info doesnt work either? I noticed when using bluetooth to my BMPCC4K that I have to have it in DF mode or it does function correctly. It feels like a quality product, but is being let down my the bugs, come on Tilta more updates please.

@poti732

7 ай бұрын

Same , just use custom mode for the zoom not the zoom mode

Is there an accessory for mounting the hand wheel controller to a 15mm rod?

@thegentlestories214

7 ай бұрын

i want the same ;)

@leonpowell1044

6 ай бұрын

Tilta 15mm Rod Holder To NATO Adapter and a short nato rail

@sergioam12

6 ай бұрын

Thank you!! @@leonpowell1044

This video should have been released prior to launch.

You say you will go over the handle firmware update at a later point, but I don't see that anywhere... I updated my wheel and when trying to do the handle it sits at 100% but then the handle doesn't boot. It only boots when in upgrade mode and shows the original firmware

@TILTA

Ай бұрын

Here is the link: kzread.info/dash/bejne/d4GEvLdpiZmdZLw.html

To all the Canon Users: Is anybody able to connect the hand wheel or the hand grip to the Canon R5C in video mode? Which USB setting in camera are you using? Which setting the the hand wheel. Nothing seems to work.

Trying to connect my Tiltaing Right Side Advanced Focus HandleType VI to the nano ii doesent work. Do I Need a specific cable or is not meant to work together ?

@optical-sound

8 ай бұрын

I have the same problem. I was told by Tilta a month or so ago that a future Nano II motor firmware upgrade would fix this 'over the next month or two'. So I hope it comes soon..

@alexlubensky

7 ай бұрын

Right now it also doesn't work with Nucleus M handgrips. Once the NANO2 FIZ boots up - it switches all motors to be controlled from the NANO2 FIZ and it's impossible to unlink a motor from the NANO2 FIZ like it was possible on the M FIZ. Lots of stuff to be fixed still

@TILTA

6 ай бұрын

We will be releasing a new cable for the Right Side Advanced Focus Handle to work with the Nano II motors soon.

@OutTime

6 ай бұрын

@@TILTA ok Cool please Sent it to me for free it was advertised differently.

@alexlubensky

6 ай бұрын

@@TILTA how about ability to control zoom from Nucleus M handgrips while controlling focus from Nano II? Basically an ability to remove link to sertain motor numbers in the nano II system like it is already done in the Nucleus M system and old Nano (I can use my NANO 1 simultaneously with Nucleus M grips controlling focus on my M motors)

The interface for entering your own lenses is crude, doesn't appear to be explained anywhere but it kinda works (it's in System/Lens). Wish it would let you go back and edit the patches somehow. The software barely makes use of the hardware. Why can't you pre-program a zoom zoom or focus pull to time with a slider? Doesn't feel like it's delivering great value as it stands in 01.24. And the outlay for good usb c pd power supply isn't negligible either.

When will there be an update for Nikon Z8???

@TILTA

9 ай бұрын

We do not have a eta yet but we are trying our best to push it now.

Anybody here knows how to firmware update the side handle without owning a control wheel?

When will Nano II be the complete product with the functionality that is being advertised? When will it stop being just the most basic remote follow focus?

2 ай бұрын

I'd love some auto features like being able to set A and B points and a transition time 1sec, 2sec etc... they could do some really cool stuff with this like using focus and zoom motors to do auto-vertigo etc... it would be great it if the hand wheel controller had a dedicated "Auto" page with presets! Also I don't understand why setting A and B points normally doesn't use hard stops. It's impossible to hit focus/zoom accurately which makes it pretty useless (this would take 5 seconds to implement). Tilta need to up their game - they've been making this product for 10 years - the UI and software features should be much more polished/advanced. The UI currently feels like 50% is a placeholder to make it look more functional than it is!

The set up of this needs to be simpler. Unfortunately I'll have to return mine, mine is calibrating but it just keeps spinning non stop, i able to connect however my focus wheel does not correspond with my motor at all.

I just updated the firmware of my handunit and N II motor. Where is documented what the firmware update actually improves?

@TILTA

8 ай бұрын

as of now for the current firmware update there is no documentation but for future updates we will be listing out what improvements the firmware updates make.

@konradgrokopf5288

8 ай бұрын

okay, thank your @@TILTA

Does anyone’s nuclear us randomly start calibrating or racking focus without touching anything??

Well my unit keeps disconnecting from BMPCC4K via Bluetooth, what's more after reset it forgets the WiFi password, any pointers to fix that?

@TILTA

9 ай бұрын

Yes, next firmware will keep the wifi password to stay, the reason we set it forget cause some cameras will need to be connected by wifi. Bluetooth distance is 5-10 meters.

@JacoxNovak

9 ай бұрын

@@TILTA Ok, thanks for the reply:) Is there any expected date on the firmware release?

@AmazeStudios

8 ай бұрын

Retyping the Wi-Fi password every time is tiresome

02:54 The one detail that threw me for a loop is when Nick said not to slide this onto a regular NATO rail. If I can't mount this on a regular NATO rail, I may be sending version II back in favor of version I. How would you mount this to a camera cage as shown in product photos or to a handle on a rail system? Is there even a single 1/4-20 on it? Did I miss something? He did emphasize "slide" so maybe he means to take care when mounting it.

@leonpowell1044

6 ай бұрын

The clamp fully opens so you can mount on a nato rail just don’t slide it or maybe tape the contacts

When adding a manual lens, what is used to indicate infinity?

@TILTA

8 ай бұрын

Infinity should be indicted on the lens itself. Please email support@tilta.com if you have any other questions regarding this.

@alexlubensky

7 ай бұрын

@@TILTA there are lenses that can go past infinity (like most cine zoom lenses and some fix lenses), the lens hard stop is beyond the place where the infinity mark is. The question is - what should be written in lens value to manually set infinity for such lenses. Like I have tried just typing in "INF" and it sets it as a random focus distance very far away. Is this the correct method to assign the infinity spot of the lens or what's the trick here?

@mrshaheedmalik

7 ай бұрын

@@TILTA I'm talking about in the software. Without a way of indicating infinity, how do I properly map the lens?

@leonpowell1044

6 ай бұрын

There is an infinity symbol third input page but it doesn’t show when you choose the user lens it will just give you a numerical value but you you do get a symbol on the display ring

@TILTA Please, fix the ability to unlink a motor from the NANO 2 FIZ, like it is already done on the M FIZ. Right now when the NANO2 FIZ can not operate simultaneously with M handgrips, thus one can't control zoom on M handgrips and focus through NANO2 FIZ. Once the NANO2 FIZ boots up the M handgrips will stop working. Please, make it possible to unlink a motor in the motor menu, right now you can tap on the link, it will show you're tapping on it, but nothing happens.

What if you lost control in the wheel but not handle?

Is the rocker completely analog? Meaning the more it is pressed, the faster it goes?

@TedHolmwood

7 ай бұрын

Yes, it's variable and you can feather the speed

@alexlubensky

7 ай бұрын

no it's not, it is a combination of analog to digital gain. The FIZ has several settings to adjust the speed of the rocker, starting with the actual zoom rocker speed and ending with motor stiffness and sensitivity

Can I pair the new nano handle ii with núcleos m motors ?

@TILTA

Ай бұрын

yes this works

Is there no auto calibration?

Support for lumix camera control?

@TILTA

6 ай бұрын

this is something we are working towards.

I have canon r5 and R/S usbc cable. And no idea how it works. Can`t connect each other. Have anyone manual?

23:00 "You'll also want to make sure that both the control handle and the hand wheel are set to the same channel" - how please?

Can I expect R/S control for red comodo X?

@TILTA

7 ай бұрын

we are working towards making this happen

I just received the Nano II system with remote control grip. The included manual is in Chinese. I don't see an English version manual on Tilta's web site. Does an English manual exist?

It doesn't find any deice in the device list while connecting....

How do you update the handle?

@leonpowell1044

6 ай бұрын

See download manual it tells you Contact wheel to handle keep handle off Connect to Wi-Fi Turn on handle while holding M button Go to firmware update on wheel scroll down to handle and update unit

What if the motor doesn’t stop after 15 seconds, when hitting auto calibration?

@gadgets_and_gear

8 ай бұрын

Mine did the same. I had to pull the power source.

@TILTA

8 ай бұрын

this issue should be addressed in a future firmware update. more info coming soon

@pascalg.8111

8 ай бұрын

Hi. Did you find a work around for this? So far I haven't been able to use the follow focus because of this.

@pascalg.8111

8 ай бұрын

@@TILTA When can we expect that?

Why can't it connect with the Sony with bluetooth, at least for the record function?

I got one already and I cannot upgrade the software on the wheel..tried already more than 30 times..maybe you should have an info video about that only.

@streetlife20

6 ай бұрын

Same here

@leonpowell1044

6 ай бұрын

Is the wheel connected to the internet via Wi-Fi?

@avis144

6 ай бұрын

@@leonpowell1044 yes it is. Annoyingly, every time the update get stuck a restart needs to be done on the wheel..than, all the network details needs to be retyped again. I already gave up on updating it..tried about 50 times.. I Wrote Tilta but never got an answer. If you thinking getting one then wait.

@avis144

6 ай бұрын

@@streetlife20 do you have any development of any kind from your Nano upgrade process? I still cannot get my’n updated.

Lets address the elephant in the room. Is it possible to trigger run stop on Red Komodo 6K from the Nucleus Nano II wheel or handle?

SONY CAMERAS CONTROL: Unfortunately control (other than record button) with sony cameras is still very average. Also, the loud vibration sound for each setting change is very unpleasant :( Can you give us the option of switching it off or reducing it by 95%? In addition. Each time I change the shutter or ISO there is a noticeable delay.

@poti732

7 ай бұрын

The delay is very bad . You can turn off the vibrations tho

How do i Mount it to a nato rail if I dont slide it ? That is the point of the nato rail.

@ouvertcinerental5617

9 ай бұрын

Don't do it anyway. The pins really break. I know it for sure :-) Use the attachment method you see in the video.

@poti732

9 ай бұрын

@@ouvertcinerental5617where ? There is no explaining in the video on how to attach.

@poti732

8 ай бұрын

@@dans2833 nope , I CAREFULLY slide it so the nato rail does not touch the pins, otherwise this is bad design , the pins should have a protective cover…

@poti732

8 ай бұрын

Mine keeps twisting off if I just put it on and lock it , I make sure that it is IN the nato rail but still . To be honest i dont care about the fkn pins at this point , I dont use it on the ronin and if I ever would I can just plug in the V mount to charge it up .@@dans2833

@alexlubensky

7 ай бұрын

@@poti732 Mine came in without pogo pins, it's a flat pogo design now

My Motor is stuck on firmware update after multiple attempts to restart.

@AmazeStudios

8 ай бұрын

It’s now moving after a power cycle and the power for the motor needs to be on the bottom. No usb connection between the wheel and motor.

i need conect to fujifilm xh2s...

@TILTA

6 ай бұрын

this is something we are working towards.

@ZZProduction

6 ай бұрын

@@TILTA I'm really looking forward to it

How to connect nano ii handwheel to dji motor via 2.4G?

@unihumi

7 ай бұрын

I think it's not possible yet.

@UR4UNV

7 ай бұрын

@@unihumi just got official answer - you right

@UR4UNV

7 ай бұрын

@@unihumi yet

@unihumi

7 ай бұрын

@@UR4UNV thanks for confirming with me

is it possible to connect it with A7sIII ?

@poti732

9 ай бұрын

Yes i use it with that.

@RobertoMettifogo

9 ай бұрын

@@poti732 how did you connect it? I tried wifi and usb-c but can't make it work... thanks

@poti732

9 ай бұрын

@@RobertoMettifogo you plug in the motor with the usb C port on the upper side to the camera's usb C and the lower usb C port goes to the powerbank / battery . You need to enable PC remote control on the camera settings to do this , if it is grey and you cant you have to turn off Smartphone remote control to turn on the PC remote control, from that it will work fine. the point is the unit does not have to be connected to the camera just the motor so it is still remote , you can still use it in your hand or give it to another person .

@RobertoMettifogo

8 ай бұрын

@@poti732 I have just the hand controller, not the motor since I plan to use it with my AF lenses, but I can't connect it to the camera, nor with wifi or cable, did all you said and tried other ways but nothing..

@poti732

8 ай бұрын

So if i get you right you ONLY want to use the handcontroller to set camera settings and not to control the motor right ? If so ill tell you in steps again what you need to do : step 1 you NEED some sort of tilta nucleus motor even if you dont use it to be able to connect the handwheel to your camera. step 2 You will find 2 USB C ports on your tilta nucleus motor , the top USB C port OF THE MOTOR itself ( not the handwheel ) needs to be connected to the camera's USB C port . Step 3 Connect the motor to some sort of powersource with the bottom USB C port on the motor . Step 4 Enable PC remote control on the camera if you cant than disable smartphone control and you will be able to . Step 5 Enjoy it is connected . So the basic idea is that the motor has to connect to the camera not the handwheel and you NEED a motor do do this even if you dont use it because Tilta wants to keep the handwheel wireless to be able to operate from. a distance so it actually sends the signal to the motor and than the motor with the usb C sends it to the camera. @@RobertoMettifogo

Hi folks, does the Nucleus Nano II works with the Blackmagic Camera app for iPhone 15 Pro/Pro Max? I am aware the Nucleus M and the previous Nano works. Just trying to make sure if the Nano II also works.

@TheRealJasonEvans

8 ай бұрын

I haven't gotten it to work, yet. I'm hoping it's included in an upcoming firmware update.

8 ай бұрын

@@dans2833 yes. Controlling the Blackmagic camera

@TILTA

6 ай бұрын

Yes, it is now working with our new firmware.

6 ай бұрын

@@TILTA nice! ❤️

@TheRealJasonEvans

6 ай бұрын

I was just checking the latest version of the BM app on a whim and found that it works on last week’s update along with the latest Nano FW!Thanks Tilta!!! Awesome Christmas gift!

cant get the bluetooth to find my camera

Eg "I currently have this set to blue, which is motor number 3". Is it this= Purple = 1 Green = 2 Blue = 3 Yellow = others (???)

@MechaUsagi

4 ай бұрын

You say what the colors functions are at 9:21, but not the numbers.

Main ui

Very confused why they release all this vision of the handle and still the date is a mystery.

@ivanovskiphotography2748

9 ай бұрын

its Oct 20th tilta responded to my coment

@jsrrox

8 ай бұрын

Thanks mate!@@ivanovskiphotography2748

@ivanovskiphotography2748

8 ай бұрын

they deleted their coment so it is not 20 october obviously .....

@bsc001

8 ай бұрын

I ordered the handle and a 2nd motor, together with the base kit. Base kit arrived last week, and handle and 2nd servo shipped yesterday. Should arrive in my hands here in Australia early next week, but anyway, tracking info is updating. Hopefully that helps you a bit.

@TILTA

8 ай бұрын

There has been a slight delay but it is looking like early November. Please keep your eyes peeled on our socials and website for more info regarding the official launch date.

Can the motor be powered by plugging the USB-C directly into the USB-C port on the FX3?

Interesting... Absolutely none of these steps works for me. Even the firmware update stalls. I think I got a bum unit.

@TILTA

Ай бұрын

shoot our support department an email at support@tilta.com and we will get you squared away!

@ianmartin2924

Ай бұрын

@@TILTA Going through the return process now.

15 seconds of auto attempts before one can manually set hard stops Why so long that’s ridiculous I bet people returned their items because 15 seconds is bey vom ond reasonable troubleshooting time

@TILTA

8 ай бұрын

this issue should be addressed in a future firmware update. more info coming soon

I wanted to watch but 45 minutes of vocal fry is 44'50 more than I can handle.

Dang, what a gravelly voice

This guy has the most annoying voice.

OK, but you can’t calibrate for shit with the stupid focus rings that come with it, because they have a plastic piece that always gets in the way