Excellent job..done well to get that done in 2 days...even long days..sort of job i would dread but also want the the challenge.👍🏻

@cputilitysolutions

6 ай бұрын

Thank you! 🙌🏾

very good job chirag could only work out pump overrun through LLH because if 2 motorised valves shut external pump had no circuit unless i missed something 🙂

@cputilitysolutions

2 ай бұрын

Yup just through the LLH 👍🏾

What a difference, I mainly do service and repair now but still get customers asking what to do in this scenario so thanks for sharing at least I can give them some sort of starting point when speaking to the installer!! Love customers reaction "woop woop" 😂

@cputilitysolutions

6 ай бұрын

Always satisfying when it works out 🙌🏾

I couldn't face tracing all that pipework 😅

@cputilitysolutions

5 ай бұрын

😂

Wow you reply to every message. You're a proper youtuber. Good stuff. Thanks for finding the time whilst you do your day job and family life. Onwards and upwards.

@cputilitysolutions

9 ай бұрын

I try my best!

Awesome job

@cputilitysolutions

9 ай бұрын

Thanks man 👊🏾

Great job mate 👏

@cputilitysolutions

9 ай бұрын

Nice one mate 👊🏾

Nice job 👏

@cputilitysolutions

9 ай бұрын

Thank you 🙏🏾

great job

@cputilitysolutions

9 ай бұрын

Thank you 🙌🏾

Cracking job mate, well explained, The customers look very happy also, 👍👍🤜

@cputilitysolutions

9 ай бұрын

Cheers mate 👊🏾

Wicked piece of work 🎉.

@cputilitysolutions

9 ай бұрын

Thanks man 🙏🏾

Nice job the only thing I would have done is put a gate valve on either flow or return to the cylinder, just to tweak down the flow going through the cylinder, will help the heating circulate better and be pushing full belt against the heating return.

@cputilitysolutions

9 ай бұрын

Ah yes good shout!

System working better than before ? Is it all working ok to best of your knowledge ? Your leak free systems happy your happy customers happy sounds like job well done to me 🤷🏻‍♂️ well done

@cputilitysolutions

8 ай бұрын

Thanks 👍🏾

Nice job mate. I made the same mistake with the return on a cylinder easy mistake i found out the hard way🤣

@cputilitysolutions

9 ай бұрын

Always happens when you got so many different pipes to tie in 🤣

Great install . Only thing I noticed was the safety discharge pipe. Should be high temp , typically push fit polypropylene or copper. ABS isn't high temp so when the cylinder temp relief opens at say 90° c the pipe won't carry that temp . Not too sure about the condense being run into it . Having said that it looks impressive & one happy punter 👍

@cputilitysolutions

9 ай бұрын

Cheers mate 👍🏾

Brilliant workmanship just one comment the house that size surely requires a secondary return pump fitted somehow ? But as long as the customer is happy well done again.

@cputilitysolutions

9 ай бұрын

Ideally yes, but we didn't have provisions to run a secondary return unfortunately

Do you ever use automatic filler valves instead of the filler loop?

@cputilitysolutions

5 ай бұрын

I've not used them myself personally

@fionnan2811

5 ай бұрын

@cputilitysolutions they are handy to fill a system while you are venting it and so on.

Does the boiler need any clearance from the wall?

@cputilitysolutions

8 ай бұрын

5mm

Good job mate ….when the boiler is circulating within the low loss header I take it the external pump stays off whilst this is going on ? Then when the customer calls for heat the boiler tells that pump to come on ? This may sound silly but how does the boiler know just to do that small circuit.

@cputilitysolutions

9 ай бұрын

Thanks mate, so both pumps will only come on when the customer calls for a demand. The boiler circuit will always take the path of least resistance so it will naturally just circulate through the LLH. Hope that makes sense

Great job, thanks, what a stupid installation they had, two combi? What was the issue with them that need replacing?

@cputilitysolutions

9 ай бұрын

I think the heat exchangers had gone, it was my mate's install so he'd been there initially to diagnose the issues. The system wasn't fit for purpose regardless so it was screaming to be sorted 🙌🏾

Aha I am guessing 2 x ecomax with condense collectors gone I have changed a good few of them over the years... 😂😂

@cputilitysolutions

9 ай бұрын

🤣

Great job m8. Why the 2 combis?

@cputilitysolutions

9 ай бұрын

Thanks man, I have no idea why there were 2 combis in the first place 🤦🏾‍♂️

LLH acts as a bypass and a buffer to stop a system side pump robbing the water too fast out of a boiler causing lack of temperature rise and wasting gas/electricity. Sadly I come across a lot of double 30kw boilers shoved in and domestic engineers forget that it straddles that commercial line and can't be treated as 2 separate appliances. I spotted one of the other commenters picked up on the pressure relief, they're correct - the only other ways round it is sizing up (2 or 3 or 4 inch pipe) or look up the temperature rating of the plastic waste pipes for water flow per meter. As if it's fast enough over a short enough distance that's the only other way of doing it. I don't know if the tables are current though or even allowed to be used anymore. If you even know the manufacturer/type of plastic pipe currently installed. Side note, you can have the condense go into it if the boiler has it's own condense trap which won't get effected (condense sucked out) should the tank relief go. Cracking install and your understanding is definitely getting up there. 👍

@cputilitysolutions

9 ай бұрын

Thanks for the feedback mate and thanks for watching, much appreciated 👍🏾

Whats the low loss header do mate

@wolvolad25

9 ай бұрын

You actually explain at the end 😂

@cputilitysolutions

9 ай бұрын

👍🏾

Were did u park your van in southall lol 😂

@cputilitysolutions

9 ай бұрын

At my cousin's

Blow off from the cylinder wrong sorry 😇

@cputilitysolutions

9 ай бұрын

Thanks 👍🏾