Super Bee w/ a 3 channel radio, Gas RC Kill Switch, Killer RC
Ойын-сауық
I explain how to set the Super Bee for use with a 3 channel radio. Plug the Super Bee into your Aux channel, and both dip switches should be up. www.KillerRC.com for more info or to purchase a Super Bee.
Пікірлер: 34
Very good explanation. Thank you :-)
I thought you needed a cutoff switch to be able to use the third Channel. please help
hi I'm wanting to run etc Leds off my killer bee so I can see it x from a distance can you point me to a how do please thank you
Does Super bee kill switch work with Spektrum AVC because my Spektrum AVC interferes with it. When the AVC is on, the kill switch automatically turns the engine off and it doesn't take any input from the transmitter thereafter. So I have to turn off the AVC and then the switch gets turned on or off from the transmitter.
Osmar Castillero I did every single test And I notice if you or if the coil cable get disconnected from the supper bee kill switch the engine still running. I tape my around to make sure will not comes off
@MrKillerRC
5 жыл бұрын
Yes. Make sure the ignition wires wires are securely connected to the ignition coil. You can pinch the spades with pliers to make them fit more tightly.
Another video and another video and another video
what if the receiver stops working ?
Hi guys Can you please send me the link to the 2 channel kill switch- thanks
What's is up ? You mean towards wire terminals or what
How dose it shut down the car?
Where is killer rc i ordered one and its been 2 weeks no response no calls nothing?
i turn off my transmitter but the killer be doesn't cut off the engine... everything works fine otherwise. help please
@MrKillerRC
8 жыл бұрын
Info@killerrc.com Probly just need radio settings changed.
@faniss1380
5 жыл бұрын
I have the same problem. Did you find a solution? Please let me know
Could u do one on the stock losi spectrum receiver I have the dx4s and the new kill switch
@pb2themax
10 жыл бұрын
For a 3 or 4 channel radio you don't need to change any settings on the Super Bee. Just set the radio like this. www.killerrc.com/forum/viewtopic.php?f=13&t=1077
@craigtreeguy
10 жыл бұрын
Thanks for the reply
Hi bud, having a problem, I shut the radio off and the kill switch stays on?
@MrKillerRC
5 жыл бұрын
Depends on what radio you have. You probably just need to change how the failsafe is set on the receiver. Hold down the Aux button (Super Bee LED red) while you rebind the transmitter and receiver. Try that out
@phuckyou73
5 жыл бұрын
That you saved my ass again
I have a 4 channel receiver but only 2 channel transmitter. Which video should I follow?
@pb2themax
10 жыл бұрын
Treat the receiver like its a 2 channel receiver. There will be power on channel 3 and 4 but no signal. So you'll need to put a splitter cable on the steering channel for the Super Bee. Flip down the #1 dip switch on the Super Bee to turn off Aux control.
@joemilnes9062
10 жыл бұрын
Ok thanks. So even if I plugged it into ch 3 or 4 and turned my transmitter off simulating a radio glitch, nothing would happen?
@pb2themax
10 жыл бұрын
Joe Milnes With a 2 channel transmitter, If you plug the Super Bee into channel 3 or 4 the Super Bee would think there is a constant radio glitch and you'd never be able to start the engine.
@joemilnes9062
10 жыл бұрын
Oh thanks for the help!
Yeah same problem anyone using a spectrum dx5c
@MrKillerRC
5 жыл бұрын
crazy4baja Both dip up on the Super Bee. Plugged into the Aux. Hold the Aux button in the off position (Super Bee LED Red) while you rebind the transmitter and receiver.
@phuckyou73
5 жыл бұрын
@@MrKillerRC that was a big help and than you so much for getting back with me big help cheers
It comes on red at first i hit channel 3 it goes green runs for a minute shuts off
@MrKillerRC
4 жыл бұрын
Roderick Taylor Does this only happen when the engine is running? It could be radio interference from a bad spark plug resistor. Install a new NGK CMR7H spark plug and try it.
@rodtaylor62
4 жыл бұрын
@@MrKillerRC ok thanks
For installation on a HPI Baja see this www.killerrc.com/forum/viewtopic.php?f=25&t=586 For installation on a Losi 5IVE see this www.killerrc.com/forum/viewtopic.php?f=25&t=565