This looks really good 👍

Impressive results, I'll have to give this stuff a try. I ordered a bottle of their "nylon-like" resin a few months back, but it didn't work the way I was expecting it to. This is much more in line with what I would've wanted from a tough and flexible resin.

@greedy3d480

Жыл бұрын

It is very good

A very thorough test and comparison. Thanks!

@greedy3d480

4 ай бұрын

Glad you liked it!

ABS-like is my favorite resin from them, i should try this one and nylon

THIS IS THE WAY! :)

@greedy3d480

Жыл бұрын

🤣👍

This will be great for printing action figures or anything with moving parts

@greedy3d480

Жыл бұрын

Yeah I agree

Nice Video! Can you also provide the Slice Parameters you used (layer thickness, normal exposure time, bottom exposure time, Lift distance, lift/retract speed, etc...)?

The Basic sunlu the force your pulling that is still pretty damb good compared to elegoo and anycubic basic ive used! I just got a 2kg bottle as wrong order so away to experiment and mix some of the ABS on with it! I might make it just that bit stronger for using up I'll not waste it! I cannot find the Toughness resin anywhere to get some to try,Weird!

I wonder if this is a re-branding of their ABS-like resin? It's my favorite for sure. You can literally tie supports in knots if you want to because it's so strong and flexible.

@greedy3d480

Жыл бұрын

Hmm note sure

@Fabodroidgaming

6 ай бұрын

I dont think so, i use their ABS-like resin (its my go to resin) and it is way more brittle than the toughness one. I recommend to mix them. I do ratio 10:1 ABS-like/Toughness, its firm and detailed like the ABS-like, but a lot more resiliant to impacts than pure ABS-like.

i had try it...but don't seem is " Tought " look more rubber & soft....Not hard enough......may i know what your setting?

Throws Plastic bag on floor - Loud DING heard. LOL - Keep up the amazing videos !

@greedy3d480

2 ай бұрын

Thank you 😁😁😁👍

How do you think it would stand up to parts that are hollowed, with a wall thickness of about 1.9 mm? Looks promising, so frustrating when small details break off. Thank you for the review.

@greedy3d480

Жыл бұрын

I think it would be fine it's so strong

I wonder if this could be mixed with the water washable resin to make it slightly more resilient?

@greedy3d480

Жыл бұрын

You'd have to touch base with Sunlu for that 👍

Have you tested the sunlu resin cleaner that is supposed to replace isopropyl alcohol

@greedy3d480

Жыл бұрын

No ill look into it

Hi there, thank you for the video. It was very informative. Can I ask if the cured resin powders/produce dust when it grinds? I'm thinking of making moving joints and I'd rather not found out it powders out toxic resin dust. Thanks,

@greedy3d480

3 ай бұрын

Any friction will cause dust I believe... Dependant I guess on amount of friction 👍

@user-cy9kr4hi7t

3 ай бұрын

@@greedy3d480 Thank you for the reply. I was hoping this would be a cheap replacement for the 'engineering' resins like resione. I guess I'll keep looking.

@user-cy9kr4hi7t

2 ай бұрын

@@greedy3d480 Hi there, thought I'd say after an initial test I couldn't get any dusting on my test of rubbing two flat surfaces together. I was quite thorough and didn't produce any dust. I am going to print a ball joint as a test soon but if there is no dusting, this resin could be suitable for practical or engineering parts like gears.

@greedy3d480

2 ай бұрын

@user-cy9kr4hi7t ah I assumed you meant when sanding... Not sure re ball joint.. I imagine with lubricant you'll be find

did you cure the supports to see if it made a difference to strength when you try break them?

@greedy3d480

7 ай бұрын

I cured it all

Do you have to clean the models with IPA when using this?

@greedy3d480

Жыл бұрын

Yes you do

I mixed some toughness resin with the water washable resins ( 1 liter over 6 litters waterwashable) my prints no longer snap with the small parts instantly and has some flex.

@greedy3d480

Жыл бұрын

Good to know thank you

@gabrielsantoyo442

11 ай бұрын

what kind of water washable resin did you mix?

@Buildonsound

11 ай бұрын

@@gabrielsantoyo442 sunlu water washable with Sunlu toughness resin

Can You compare this toughness resin to abs like from sunlu?

@greedy3d480

Жыл бұрын

Haven't used that one someone on here may have though

It's good for making joint?

@greedy3d480

Жыл бұрын

Yeah I'd say so 👍

To be fair to sunlu the ABS like isn’t to be sniffed at its amazing resin im 17st and not broke a model or test part yet with it! But curing is also a MASSIVE part in the last stage as over curing can just strip the resins Toughness properties out completely makong it as brittle as a basic standard! I have been told from a professional resin tester any more than 4 minutes to cure your part you are at risk of loosing the Toughness that binds it together! Sounds crazy low time but is working but still do a 5 or 6 i can't help it and larger models ive worked out myself at 22 minutes for a statue hollow at 1.8mm thick wall is just right and UV can penetrate and cure the insides at this wall thicknesses

@menent

8 ай бұрын

22 minuts curing wtf bro. i just cure 1 o 2 min my figures only , i read alot and less time is better for everithing . You need to get the rigth time to the figure not get stticky depend of the size of the figure its about 1 or 2 mins max 3. Curing piece 22 minuts porblable the resin will be like glass if you want to cure inside buy a mini led lamp and put inside a hole. But to be onest i print 1/4 figures and i never cured inside and some of the figures have 3 years they are huge and they still there, no breaks or cracks. if you wash the figure good no problems if you dont cure inside

Did you notice a detail or quality of detail difference?

@greedy3d480

5 ай бұрын

No to be honest , quality was good

I've printed over 15 bottles and agree that if you drop a model, assume it broke. Great stuff, but for show pieces only. Impressive, might have to bite the bullet on this stuff. I wish they would just call this standard and abandon the old.

@greedy3d480

7 ай бұрын

Yes I went back to it again recently and it is very brittle compared to other mskes that I'm using at the moment

When ppl say hard they think of tough, if you want anything to withstand real world use and stress, it needs to retain its shape yet be flexible enough not to shatter on impact or with bending or repeating abuse. The only things that should truly be hard, should be thing that cut into other objects or etch them unless they want something that is basically like glass.

@greedy3d480

Жыл бұрын

Thank you for your comment 👍

how it compares to abs-like?

@greedy3d480

7 ай бұрын

Abs much stronger and less brittle

@MrHoodsquirrel

7 ай бұрын

@@greedy3d480 Abs like is stronger compared to this? I thought Sunlu tough would be stronger

Damn batman. This stuff is expensive 😮

@greedy3d480

6 ай бұрын

yep it aint cheap