You just saved me an expensive trip to the gunsmith. Thank you!!!

@devildog_iii3492

3 жыл бұрын

Glad to hear! Thanks

This is the only video I can find doing this. Thanks

Ive been having a lock open after every round problem, narrowed it down to the slide lock/ release spring. @ 7:43 in this video saved me from going crazy and selling this damn gun! Now she works 100%!! Thank you so much for this video!!!! VERY HELPFULL!!

@devildog_iii3492

11 ай бұрын

Thanks bud, glad it helped. Must of been super frustrating haha

Very nice! Hellcat is easy to do a complete breakdown like the glock, but Hellcat seems to have a much better trigger. Great vid bud, keep up the good work.

@devildog_iii3492

3 жыл бұрын

Yea it’s not bad to take down at all. Thanks bud, appreciate it.

Thank you very much for this vid!!! I just bought a hellcat site unseen and it turns out its very bad inside, i need to remove all the guts. I couldnt find a tear down video. This was very helpful and now im not scared to pull it apart. Thanks again!

@devildog_iii3492

Жыл бұрын

Thanks bud, good to hear! Yea that’s why I made it haha. Didn’t have a video to go by myself so dug in.

As far as I know these pistols are produced by HS Croatia as „H11“, Springfield only labeling and selling as „Hellcat“. Great subcompact, very accurate 👌

Well done, thank you, just went through all this today myself on one.

@devildog_iii3492

Жыл бұрын

Nice, Glad it helped.

Hey, thank you. You did a great job on this.

@devildog_iii3492

3 жыл бұрын

Appreciate it bud

Thx Homie, this was a good informative video, you made it very simple👍

@devildog_iii3492

Жыл бұрын

Thanks man

Nice video man very helpful 👍 You should do one on how to break down and reassemble the slide on the hell cat

There is a tiny circlip that goes on the left side of the sear housing block for the rear frame assembly pin to catch on. Easy to miss. I had a little "ah-hah!" moment myself.

@devildog_iii3492

Жыл бұрын

Oh nice haha. Thanks

@devildog_iii3492

Жыл бұрын

My buddy just texted me a pic of that cir clip “where the hell does this go!?”

@Motorrad127

Жыл бұрын

@devildog_iii3492 all good now?

@devildog_iii3492

Жыл бұрын

Yep

@michaelhawk1826

7 ай бұрын

@@devildog_iii3492I have the same problem where the hell does it go and do I even need the clip?

Thanks buddy, we needed this!

@devildog_iii3492

4 жыл бұрын

Yup! Thanks man

@iangallaghersr.710

4 жыл бұрын

@@devildog_iii3492 now we need a video on how to disassemble the slide!

@devildog_iii3492

4 жыл бұрын

Yea I will do one. There’s a couple on YT thou right?

@iangallaghersr.710

4 жыл бұрын

@@devildog_iii3492 i haven't been able to find one if there is.

@deucedeuce1572

Жыл бұрын

Reading all the good comments, it's so disgusting that there are people that would ban this kind of speech and even go out of their way to report it. They don't care about safety or anyone else, only their evil, twisted, selfish, cowardly ideology.

Great video

@devildog_iii3492

3 жыл бұрын

Thanks bud.

Awesome video, thank you so much. After 500 rounds, I'm disassembling and doing a thorough cleaning and replacing lube. I've looked in the manual booklet and it says to "lightly oil moving parts". Where all would you say needs oil? Every friction surface and moving parts including springs and internal gear movement points such as the sear assembly?

@devildog_iii3492

Жыл бұрын

Thanks. Usually do slide rails, barrel hood, striker nose and pivot/friction points, pin block.

Thanks bro this help me alots thanks Bro!!

@devildog_iii3492

2 жыл бұрын

Glad it helped

Any idea if I'll lose any important functionality by reassembling the gun without the magazine blocking lever? I believe its only purpose is to prevent a magazine from being in the gun when field stripping it, but mine rattles all the time, even when a magazine is inserted which is super annoying.

@devildog_iii3492

2 жыл бұрын

Not sure.. but I’d probably leave it

@kre8elapache802

Жыл бұрын

Did you ever take it out?

@deucedeuce1572

Жыл бұрын

@@kre8elapache802 Was wondering the same. On the P320, you can completely remove the takedown-safety lever (that is also the magazine block) and the gun will fire/work 100% normally. The only difference is that you'll have to pull the trigger to disengage the dear to disassemble (...and that you won't have the magazine block anymore either). Otherwise though, it's no big deal at all to just completely remove it. Some people do just because it's a hassle to reinstall and it offers no real protection of any kind. You have to lock the slide back to turn the take-down lever anyways, so it would be Really Hard to accidentally take it down with a magazine installed.

has anybody tried to shorten pretravel distance by shortening the sear spring like it can be done on Glock? Would that help?

@devildog_iii3492

Жыл бұрын

I haven’t heard anyone doing that. I shaved down the trigger safety/hinge some

trying to change mag release and cant take apart the spring help

@devildog_iii3492

3 жыл бұрын

Swapping it with what release?

@kkibler1

3 жыл бұрын

You figure it out yet?

@miztrusa

Жыл бұрын

Spring jus pops Out of the groove so you can swap it out.... Then slide the aping back into the groove

I get that flipping up the take down lever pushes out the magazine blocking lever. But I’m confused what pulls it back in? I’ve seen some videos where the takedown lever is flipped down, but mag blocking lever stays out which seems like a big issue to me. Thanks!

@devildog_iii3492

2 ай бұрын

I don’t recall actually.. gonna have to check now

@chrisahyo9512

2 ай бұрын

@@devildog_iii3492 thanks!

I spent 2 hours trying to put this thing back together smh this was the first and last time I will ever take this gun apart

@devildog_iii3492

10 ай бұрын

Haha she was definitely frustrating the first time around

Disconnector pin fell out of sear housing after removing trigger bar assembly- how do I reinstall?? Thanks

@devildog_iii3492

11 ай бұрын

It’s not in the vid? Can’t remember

Thanks!

@devildog_iii3492

2 жыл бұрын

Hope it helped

@jasonk.martinez6726

2 жыл бұрын

Made the difference between a bunch of small part in a bag to functionality! Very helpful!

@devildog_iii3492

2 жыл бұрын

Oh good!

My magazine blocking lever moves front and backwards on the frame and rattles a lot. Is that normal? Thank you for the video.

@devildog_iii3492

2 жыл бұрын

With the mag in or out? Cocked or not?

@John-pq8zo

2 жыл бұрын

When the magazine is in it doesn’t move as much since there’s less space to move. But I can pull it in and out about a quarter of an inch. Maybe it’s just how it’s designed some hellcats don’t do that. It is really annoying though I’ll probably sell it. It does it regardless of if the slide is cocked or not.

@devildog_iii3492

2 жыл бұрын

I’ll check mine at lunch

@devildog_iii3492

2 жыл бұрын

Mine moves maybe 1/8” out if that

@deucedeuce1572

Жыл бұрын

@@John-pq8zo Heard this from other people too. Someone mentioned taking it out, but I'm not sure if anyone tried. I know the similar part in a P320 can be removed without any problems. It just removed tha magazine block and makes it so you can take the slide off without having to pull the trigger. You have to lock the slide back to turn the take-down lever anyways, so the take-down-safety lever isn't really necessary. Just have to pull the trigger to take the slide off though, which isn't a big deal, because you KNOW the gun isn't loaded when you lock the slide back to turn the take-down lever.

I just installed, and reinstalled, the Apex trigger in my Hellcat. I can't figure out what I'm doing wrong, but every time the new trigger gets stuck. Any thoughts are greatly appreciated.

@devildog_iii3492

2 жыл бұрын

I’ll look into it, none off the top of my head tho sorry

@deucedeuce1572

Жыл бұрын

Only the new one? Ever figure it out?

Nice how to!

@devildog_iii3492

4 жыл бұрын

Thanks bro. I’ll watch ur new vid once the kids asleep

@eltenda

4 жыл бұрын

@@devildog_iii3492 no prob...stay safe

@JF-lt5zc

4 жыл бұрын

Excellent video. Now I know how to take mine apart. For the striker assembly, my eyes aren't quite good enough. Is that a hex key on the back of the slide to release the rear block to access the assembly? Thank!

@devildog_iii3492

4 жыл бұрын

I’ll take a look at it when I can today and let u know. Or there’s also videos that show slide disassembly if ud like.

I did something wrong I can’t get my slide off now lol

@devildog_iii3492

3 жыл бұрын

Does it go forward at all?

@curtishardin4519

3 жыл бұрын

@@devildog_iii3492 A tiny bit

Oh my fucking god does no one has a disassembly with the manual safety?

@devildog_iii3492

2 жыл бұрын

Hahahaha, sorry man.

@Illness.og.

2 жыл бұрын

@@devildog_iii3492 lol I ended up figuring it out

@devildog_iii3492

2 жыл бұрын

Nice. Couldn’t be too different I figured

@Illness.og.

2 жыл бұрын

@@devildog_iii3492 nope, just freaked out when I suddenly saw the thumb safety plunger and spring on the table without seeing where they were haha

@devildog_iii3492

2 жыл бұрын

Haha

Point out the sear housing pin safety. It's small as fu.ck and could be easily lost. It sets in the driver's side of the sear housing.

@devildog_iii3492

3 жыл бұрын

Yea I’ll do a revision soon