Snap Fastener Installation Tool Demo
Тәжірибелік нұсқаулар және стиль
Purchase the Snap Fastener Installation Tool here: www.sailrite.com/Snap-Fastener...
Snap Fastener Installation Tool is a small, two piece setting tool for snap fasteners. The metal anvil has two sides, one for setting buttons and the other for eyelets. This tool can also be used without the base for setting rivets. Great for setting nickel-plated brass snaps and Common Sense button-back screw studs. Not recommended for use with stainless steel fasteners.
Use of a 1/8″ hole punch is recommended to create a hole in the fabric for the snap barrel before setting. An awl may also be used in lighter fabrics to force an opening in the fabric weave for the snap barrel.
Пікірлер: 98
Thank you for showing how to install the snaps! I bought a package of Sontax brand snaps at the home improvement store. The instructions on the package were not clear. Your video helped me to understand how the pieces fit together. Your guidance ensured a successful repair.
@SailriteDIY
9 күн бұрын
I'm glad the video was helpful for you!
Ms.Gratz!!! Thank you, thank you, thank you! I have a daycare and all of the bibs that I've purchased in the past have velcro. The cost for the snap button bibs, compared to the velcro is ridiculous! So after 18 years of being in this business, I just thought of putting on snap buttons myself. This video will help me tremendously! Thank you for doing this video. I really appreciate it!
@SailriteDIY
6 жыл бұрын
You are welcome!!!
I was just looking at my snap kit that I bought from Amazon, and no, I’ve never used it. But I checked it out and I was right. But I watched your video twice, just to make sure. Thank you for your time.
@SailriteDIY
2 ай бұрын
Glad it was helpful!
Thanks for the demo, its a big help and much appreciated.
I have this exact same little kit. So I should not confuse this with rivets and rivet installation?
Can one apply this same principle to making a hole in wood?
watch out Thor ! When I put snaps on thicker leather I have to make the holes a little bigger so the snap sits flush and seats well. I use a tapered tool that stretches the leather just enough to allow that then the leather gets tight again when the snap is set. Rocket Science !
En donde consigo la herramientas para poner esos broches
Hey, thanks! Managed to make a nice knife case for a friend with a brass snap contrasting with the dark leather. Looks great!
I have an item that contains metal snaps, and I'd like to find the correct, matching snaps that go with it. How does one go about doing that?
This was great thanks for this video it helped fix my Columbia pants where the snaps broke. Used this video and like new.
Thank you!! I purchased the snaps, but couldn't find instructions on how to use them. They may have gotten lost. Thank you for the Video!!
Great demonstration. Thanks!
Show as the used whith steel please
thank you! i appreciate it! it is amazing how many things i could have fixed or saved!
Watching this after the fact that I put alot of fasteners together on a jacket! Pretty strong fasteners!
Do you sell a snap system for leather work?
I was given this link to for instructions to install the snap set I bought, these are nothing (kinda) like what I bought. Umm er. So after lots of trial and miss I got the snaps to work. BTW, these are not the cheapest.
Thank you.
Please tell me you guys sell a kit. I dont want to spend the next hour trying to figure out all the items I need to put in my shopping cart.
I can't get the first one, only the second part
I love you…..lol 😜🤣 you made this so much easier for me thank you!
Where you buy that tool
What can be done if the post will not sit any tighter against the socket? I am using the same tool kit (from General) for the same nickel plated snaps. I keep hammering but the post will not curl down flat enough for the snap to work.
@SailriteDIY
3 жыл бұрын
What is the length of the button's barrel, is it 11/64", 1/4" or 5/16" (just give me the Sailrite item number, if that easier for you)? Then how many layers of fabric are you installing the snap into? Finally which snap installation tool are you using from Sailrite?
Is there anyone that used this a couple of times and still come back to the video ? That’s me. Always have to come back to figure out which is which. 😄
Could nonmetallic snap button
Cool video...
Thank you!!
Thank You
What difference between nickel plated and stainless, which the nickel is necessary?
@SailriteDIY
5 жыл бұрын
Nickel plated brass or Stainless Steel which should you use? Both work well and are approved by Sailrite for marine use, even in saltwater conditions. However Stainless Steel is slightly more corrosion resistant than nickel plated brass and Stainless Steel is a stronger metal, so it is often considered a slightly better snap.. With that said most of the OEM boats use nickel plated brass over stainless steel snaps. Why? They are cheaper and easier to install than the SS.
@mamabear52
Жыл бұрын
@@SailriteDIY Thank you, I had the same question
thank you!
Can you combine the male and female snaps together like reversible? I'm trying to fix my mss sleeping bag.
@SailriteDIY
Жыл бұрын
I am sorry, I do not understand the question. Can you email me a photo of what you are trying to do? eric@sailrite.com
I can tell from the narrators voice..you can take his word these are good button snaps.
@Soldano88
2 жыл бұрын
🤣
@KingsDaughter.
Жыл бұрын
Very nice 😅 2:21
Gracias
Lot of thank
Very nice
Cool video but I will say , she needs a bigger mallet if there is one in this universe.
@The67Crucible
6 жыл бұрын
There is only one hammer larger, and THOR is using it... lol
@shanteezys611
6 жыл бұрын
cajunsk
@themistermax
6 жыл бұрын
Lighthammer
@artcat4980
6 жыл бұрын
😂😂😂😂
Um....I how can I get the snaps to attach with just a hammer....
@SailriteDIY
5 жыл бұрын
Well you need a snap fastener installation tool and a hammer. Then they can be installed.
This will fit on 10mm thickness?
@SailriteDIY
3 жыл бұрын
If you use a snap with a barrel length of 5/16 inch it will accommodate thicknesses of up to: From 11/64" to 1/4"
Great 👍 working
I NEED that tool,!!
@SailriteDIY
6 жыл бұрын
You can purchase it here: www.sailrite.com/Snap-Fastener-Installation-Tool
It would be better if they showed the parts more. Her hands cover up too much.
great video...my snaps are in place but when i hit them (sockets) with a hammer with the tools they seem to split....
@SailriteDIY
7 жыл бұрын
If the snap barrel splits it usually means they are a cheaply made snap. Sailrite only offers the best quality snaps from DOT, the barrels of the Sailrite snaps do not split.
@triumphmanful
6 жыл бұрын
duh !
@Stevexupen
5 жыл бұрын
you need a bigger mallet
Thanks for this! I’m stairing at my kit and tool and was like don’t bother hit up KZread.
Merci !
Screw the setters, I want that mallet. Looks like it came right out of the forge of Hephaestus.
@SailriteDIY
5 жыл бұрын
You can purchase that mallet here: www.sailrite.com/Mallet-Hammer-Style-3
@lominicdandolina
4 жыл бұрын
Just cracked the fuck up at this
@eddyvideostar
3 жыл бұрын
Im With 86: What's that?
ممتاز ممتاز👌🏻
My kit came without the Anvil, so guess it's usless unless I can figure out another way to use it without...Thanks...
@SailriteDIY
4 жыл бұрын
You must have the anvil or it will not work. If it was purchased from Sailrite please contact us with your order number and we will resolve that issue.
@Reviewing_Playing_and_More_RPM
4 жыл бұрын
@@SailriteDIY Thanks but it wasn't Sailrite, got it on Amazon from company called Seloky...appreciate it though, I've ordered a set from a different company with just the tools...Thanks again...
Know that I have this info, I'm attaching the tops of cowboy boot to my crocs
SANGAT MEMBANTU. TAPI SAYA TIDAK TAU DIMANA MEMBELI ALAT UNTUK MEMASANG KANCINGNYA 😫
I want that hammer, gotta get one !!!
@SailriteDIY
5 жыл бұрын
You can get that mallet here: www.sailrite.com/Mallet-Hammer-Style-3
holy crap lady your mallet puts Thor`s hammer to shame..
Why not stainless steel?
@SailriteDIY
Жыл бұрын
The choice is yours. Nickle Plated Brass or Stainless Steel Snaps. Stainless Steel is the best choice, but nickle plated brass is still a good choice.
awesome
Thank u so much
@dareisnogod5711
5 жыл бұрын
U R SEW VELCOM.
i live downstairs."knock it off!" lol kidding.... thank you.
🥰🥰🥰
Fixed my wallet. Thank you. :)
PLEASE SLOW DOWN AND IDENTIFY EACH PIECE SEPARETLY. I AM A BEGINNER SO I KEPT GETTING LOST.
Why can't this dude pronounce the "L" in Sail.
Thumbs down, Hammer not big enough
She thinks she’s Thor lol
@ireneuszthegr8
5 жыл бұрын
Thor and Thor LOL
NOT CLEAR! You need to do a close up! AVOID these fools!
Useless demo as no proper time to identify sequence of part assembly
Good for leather belts too 🙂
thank you!
@SailriteDIY
7 жыл бұрын
You are welcome!