Family members and friends would find this video Guantanamo bay like torture,but I dont! It takes a confident man to take one of these things apart put it back together until four am and then do it again in a few hrs time.Mine isn’t broken yet but I had to watch you rip it apart in the case that I need to. I just stumbled upon you and dont know if you have anymore videos but Ill check.Keep doing the stuff that you do!

Thank god for filming this reassembly, I have been trying to find such a video since forever 😍

@Man_De

Жыл бұрын

Glad it's helping people! Let me know how your reassembly goes.

Thank you so very much for posting this. This is exactly what I needed ❤

@echov4898

Жыл бұрын

I sent this after reassembly and I can now say I have installed the shifter on my bike and it works perfectly. Thank you so much

Reconstruction starts at 8:00

Very helpfull. Thanks. I got the second washer part, retaining the first spring, broken on mine, so I'm probably screwed unless I can get replacement, but this video was pefect to figure out what was wrong and helping reassemble.

Diagram for everything else: manualzz.com/doc/53870513/shimano-st-5500-tuas-perpindahan-rem-exploded-view

@brewerkz8342

Жыл бұрын

which it had a further breakdown, only shows the higher level assembly.

I have the shift lever off only for polishing. Can you clarify, which side does the spring end goes with respect to the wide tab on the shift mechanism? I am struggling to assemble and have return tension on the lever

@Man_De

Жыл бұрын

At 22:02 I say "It either goes in here or in here." Both times gesture to a spot on the plastic. Once I was done recording, I found out that it was the first "in here". That will be the small hole that doesn't go all the way through the plastic. Hope this helps!

@brewerkz8342

Жыл бұрын

@@Man_De just to clarify at 24.01, your removing and reinstalling the spring in the lever arm (y axis pin in the arm). Does the spring end that stick out sit on the clockwise or counter clock wise side of the wide brass color tab your pointing to?

@brewerkz8342

Жыл бұрын

@@Man_De I emailed a photo for clarity.

@maximebouvier2320

Жыл бұрын

​@@brewerkz8342 hello, I think i have the same problem. Did you find a solution ?

@Man_De

Жыл бұрын

@@maximebouvier2320 Nope, I give up. If you find a solution, let us know. (see @onemanoneideal convo)

I believe that the spring you are installing at minute 24:00 and following is pre tensioned. Unfortunately I was not able to figure out how the hell this is supposed to be done. My hands and fingers truly hurt by now. Maybe someone knows how? Or knows where that thing is supposed to be hooked onto? thank you so much in advance

@Man_De

Жыл бұрын

I had the same experience with basically no luck. I've been running it without the spring tensioned. It works well enough for my needs, but it doesn't snap back to the resting position properly, so I need to do it manually. I've ridden over 200 miles with it like this, and I'm used to it by now. BUT! if anybody finds the solution, that be great!

@lksbrn

Жыл бұрын

Dayum…

@lksbrn

Жыл бұрын

I see they completely changed the design after this awful layout in the next couple iterations

@lksbrn

Жыл бұрын

Ok so I made some progress! Using fishing line I was able to put tension on the spring before mounting- I made it to the first “hook” but ran out of luck for the actual position. The shifter jumps back into its original position but only sometimes

@sorro9120

4 ай бұрын

@@lksbrnthank you for the tip with the fishing line!! after 2 hours of trying I finally managed to get the spring to hook on to the smaller counterpart! it works flawlessly now! for anyone trying it as well: I also plastically deformed the metal spring a bit so that the "hook" is facing a little bit more outwards. I think that also helped

Helpful guy: www.flickr.com/photos/mrjoeball/8151690775/in/album-72157631921008792/