Very helpfull. Thanks. I got the second washer part, retaining the first spring, broken on mine, so I'm probably screwed unless I can get replacement, but this video was pefect to figure out what was wrong and helping reassemble.
@Man_De11 ай бұрын
Man, I was doing weird stuff my sophomore year of high school…
@glenangelos602511 ай бұрын
Family members and friends would find this video Guantanamo bay like torture,but I dont! It takes a confident man to take one of these things apart put it back together until four am and then do it again in a few hrs time.Mine isn’t broken yet but I had to watch you rip it apart in the case that I need to. I just stumbled upon you and dont know if you have anymore videos but Ill check.Keep doing the stuff that you do!
@lksbrn Жыл бұрын
I believe that the spring you are installing at minute 24:00 and following is pre tensioned. Unfortunately I was not able to figure out how the hell this is supposed to be done. My hands and fingers truly hurt by now. Maybe someone knows how? Or knows where that thing is supposed to be hooked onto? thank you so much in advance
@Man_De Жыл бұрын
I had the same experience with basically no luck. I've been running it without the spring tensioned. It works well enough for my needs, but it doesn't snap back to the resting position properly, so I need to do it manually. I've ridden over 200 miles with it like this, and I'm used to it by now. BUT! if anybody finds the solution, that be great!
@lksbrn Жыл бұрын
Dayum…
@lksbrn Жыл бұрын
I see they completely changed the design after this awful layout in the next couple iterations
@lksbrn Жыл бұрын
Ok so I made some progress! Using fishing line I was able to put tension on the spring before mounting- I made it to the first “hook” but ran out of luck for the actual position. The shifter jumps back into its original position but only sometimes
@sorro91205 ай бұрын
@@lksbrnthank you for the tip with the fishing line!! after 2 hours of trying I finally managed to get the spring to hook on to the smaller counterpart! it works flawlessly now! for anyone trying it as well: I also plastically deformed the metal spring a bit so that the "hook" is facing a little bit more outwards. I think that also helped
@echov4898 Жыл бұрын
Thank you so very much for posting this. This is exactly what I needed ❤
@echov4898 Жыл бұрын
I sent this after reassembly and I can now say I have installed the shifter on my bike and it works perfectly. Thank you so much
@brewerkz8342 Жыл бұрын
I have the shift lever off only for polishing. Can you clarify, which side does the spring end goes with respect to the wide tab on the shift mechanism? I am struggling to assemble and have return tension on the lever
@Man_De Жыл бұрын
At 22:02 I say "It either goes in here or in here." Both times gesture to a spot on the plastic. Once I was done recording, I found out that it was the first "in here". That will be the small hole that doesn't go all the way through the plastic. Hope this helps!
@brewerkz8342 Жыл бұрын
@@Man_De just to clarify at 24.01, your removing and reinstalling the spring in the lever arm (y axis pin in the arm). Does the spring end that stick out sit on the clockwise or counter clock wise side of the wide brass color tab your pointing to?
@brewerkz8342 Жыл бұрын
@@Man_De I emailed a photo for clarity.
@maximebouvier2320 Жыл бұрын
@@brewerkz8342 hello, I think i have the same problem. Did you find a solution ?
@Man_De Жыл бұрын
@@maximebouvier2320 Nope, I give up. If you find a solution, let us know. (see @onemanoneideal convo)
@MrSimfel Жыл бұрын
Thank god for filming this reassembly, I have been trying to find such a video since forever 😍
@Man_De Жыл бұрын
Glad it's helping people! Let me know how your reassembly goes.
@BetaClimbers Жыл бұрын
Now you just need a big net 😂
@Man_De Жыл бұрын
That's the plan. I should have the net built by V4.
Пікірлер
Reconstruction starts at 8:00
Very helpfull. Thanks. I got the second washer part, retaining the first spring, broken on mine, so I'm probably screwed unless I can get replacement, but this video was pefect to figure out what was wrong and helping reassemble.
Man, I was doing weird stuff my sophomore year of high school…
Family members and friends would find this video Guantanamo bay like torture,but I dont! It takes a confident man to take one of these things apart put it back together until four am and then do it again in a few hrs time.Mine isn’t broken yet but I had to watch you rip it apart in the case that I need to. I just stumbled upon you and dont know if you have anymore videos but Ill check.Keep doing the stuff that you do!
I believe that the spring you are installing at minute 24:00 and following is pre tensioned. Unfortunately I was not able to figure out how the hell this is supposed to be done. My hands and fingers truly hurt by now. Maybe someone knows how? Or knows where that thing is supposed to be hooked onto? thank you so much in advance
I had the same experience with basically no luck. I've been running it without the spring tensioned. It works well enough for my needs, but it doesn't snap back to the resting position properly, so I need to do it manually. I've ridden over 200 miles with it like this, and I'm used to it by now. BUT! if anybody finds the solution, that be great!
Dayum…
I see they completely changed the design after this awful layout in the next couple iterations
Ok so I made some progress! Using fishing line I was able to put tension on the spring before mounting- I made it to the first “hook” but ran out of luck for the actual position. The shifter jumps back into its original position but only sometimes
@@lksbrnthank you for the tip with the fishing line!! after 2 hours of trying I finally managed to get the spring to hook on to the smaller counterpart! it works flawlessly now! for anyone trying it as well: I also plastically deformed the metal spring a bit so that the "hook" is facing a little bit more outwards. I think that also helped
Thank you so very much for posting this. This is exactly what I needed ❤
I sent this after reassembly and I can now say I have installed the shifter on my bike and it works perfectly. Thank you so much
I have the shift lever off only for polishing. Can you clarify, which side does the spring end goes with respect to the wide tab on the shift mechanism? I am struggling to assemble and have return tension on the lever
At 22:02 I say "It either goes in here or in here." Both times gesture to a spot on the plastic. Once I was done recording, I found out that it was the first "in here". That will be the small hole that doesn't go all the way through the plastic. Hope this helps!
@@Man_De just to clarify at 24.01, your removing and reinstalling the spring in the lever arm (y axis pin in the arm). Does the spring end that stick out sit on the clockwise or counter clock wise side of the wide brass color tab your pointing to?
@@Man_De I emailed a photo for clarity.
@@brewerkz8342 hello, I think i have the same problem. Did you find a solution ?
@@maximebouvier2320 Nope, I give up. If you find a solution, let us know. (see @onemanoneideal convo)
Thank god for filming this reassembly, I have been trying to find such a video since forever 😍
Glad it's helping people! Let me know how your reassembly goes.
Now you just need a big net 😂
That's the plan. I should have the net built by V4.
@@Man_De 😂 keep me posted
Helpful guy: www.flickr.com/photos/mrjoeball/8151690775/in/album-72157631921008792/
Diagram for everything else: manualzz.com/doc/53870513/shimano-st-5500-tuas-perpindahan-rem-exploded-view
which it had a further breakdown, only shows the higher level assembly.
It's way cheaper and easier to buy a pack of primers. No need to destroy a shotshell.
Good video by the way.
You can time this with a suitable piece of ice which can be great fun))