NB Miata Key’s Racing Steering Wheel Install!
Автокөліктер мен көлік құралдары
Here’s a full tutorial on installing my Key’s Steering Wheel as well as an NRG Quick Release with a Momo hub! Decided it was time to have a video actually showing you how to properly have a working horn and with no airbag light as well. Process was fairly simple, just time consuming, and I hope I was able to help guide you to properly install your wheel/ quick release. Let me know if you have any questions/ comments/ concerns!
Steering wheel:
www.nengun.com/keys-racing/dr...
Hub adapter:
www.ogracing.com/products/mom...
Quick release:
www.amazon.com/NRG-Innovation...
Forum post for horn button: forum.miata.net/vb/showthread...
Pictures credits:
ER34 - gran-turismo.fandom.com/wiki/...
KZread video screen grabs credits: • GT6-BLITZ DunlopER34 S...
Social:
* Instagram - / dapetdetect. .
* Tik Tok - vm.tiktok.com/4qBS3g/
*Twitter - dapetdetective
Thumbnail created using Canva.com and their iOS app.
Credits:
Music
Track: Arya, borne & Lynzz - Need U [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Arya, borne & Lynzz - ...
Free Download / Stream: ncs.io/NeedU
#nb #miata #steeringwheel
Пікірлер: 38
thanks this helped me un-mod my steering wheel and go back to stock, seeing all the connector locations and factory routing 👍
@dapetdetective
Жыл бұрын
No problem! Thanks for checking it out!! Glad I could help 🙏.
Got mine done today. Thanks! your video was very helpful! Also would like to say for an NB1 I was able to get my SRS Airbag light to go away with 1x 3.3 ohm resistor.
@dapetdetective
2 ай бұрын
Suoer glad I was able to help! My main goal with these vids haha. And cool deal I appreciate the note! Hope you enjoy the new setup 🤘
Thank you so much for this!
@dapetdetective
Ай бұрын
Glad I could help!!
perfect video man
@dapetdetective
Жыл бұрын
Thanks so much for checking it out man!!
I just tried to put my steering wheel on and looking at your video what I did with the horn was cut the green connector off and make a wire and attach it using a quick disconnect as power am I wrong and the green wire is ground and the wire inside the hub will connect to the button and work
Nice video! I'm wondering though, did turning the prongs you show at 7:18 by 90 degree to fit your hub affect the turn signal canceling mechanism?
@dapetdetective
Жыл бұрын
Appreciate the words!! No issues at all, skip over to 20:23 and I show it working!
Did the hardware and Allen wrench you used to install the steering wheel come with the hub or your wheel?
@dapetdetective
11 ай бұрын
The wheel hub does come with the hardware and wrench required but I bought the fancy blue color ones for aesthetics separately!
hello, would u be able to link a website to find that blue splice box thingy u used for the horn wire? awesome vid btw!
@dapetdetective
Жыл бұрын
Hello! So I had that thing on hand in one of my electrical kits, but if you Amazon or Google “wire splice kit” or something similar it should come up!
How much torque for the center nut? I tried to find some figures but no luck. Installing my wheel in a few days. Thank you so much for explaining everything so well in your video love it 🙌🙌
@dapetdetective
9 ай бұрын
Thank you so much and for watching! Glad ai could help. So I found 36 ft-lbs floating around as spec but personal I feel better a bit higher so maybe 40-50 ft lbs to be safe? Just be careful with some lower quality hubs being probe to cracking from over torque. But I’ve never had issues with my Momo hub in any vehicle I’ve had.
@itz_-spyro-7104
9 ай бұрын
@@dapetdetective thank you so much, I've got a luisi mirage wheel and hub so really good quality, will probably use 40 and if it feels not enough might as well use a bit more. Looking forward to new videos of yours. 🙌🙌
What ohm resistance were those resistors you installed. 19:32
@dapetdetective
8 ай бұрын
Been a while but if I remember right, should be 2 3.3 ohm resistors!
@zachoryjamnik5605
8 ай бұрын
@@dapetdetective thankyou!
what shift knob is that where can I get one for my NB
@dapetdetective
Жыл бұрын
So the shift knob actually comes with the entire IRP shifter assembly sadly and apparently VERY hard to remove haha not even sure if it’s possible without damaging the finish. The install and links to check them out are actually in my previous video, IRP Shifter install!
@jake-jl6gx
Жыл бұрын
@@dapetdetective Uh oh hahaha, It just looks so frickin sick, is it chassis mounted ?
@dapetdetective
Жыл бұрын
@@jake-jl6gx Haha I love it man! Lemme link it to give you an idea! It’s actually like a normal shifter, nothing fancy, mounted to the stock shifter housing atop the transmission. Here’s the vid: kzread.info/dash/bejne/jKiI3MGFqrHWktI.html
@jake-jl6gx
Жыл бұрын
@@dapetdetective thanks!
@jake-jl6gx
Жыл бұрын
@@dapetdetective I’m gonna try and install my quick release stuff today, I just know that the horn is gonna be a pain in the butt
Did all this make it awkward to reach the blinkers?
@dapetdetective
3 ай бұрын
At first it’s odd for sure but I got used to it pretty quick!
@mihaiserbanescu8676
3 ай бұрын
@@dapetdetective I have an airbag light on and I'm looking to do a quick release to get rid of the issue. I was wondering if I'm gonna have to take my hands off the steering wheel to reach the stalks. It looks like there is no middle ground with this issue.
@dapetdetective
3 ай бұрын
@@mihaiserbanescu8676 honestly I just had to reach a tad more than comfortable but if you run no quick release or also a flatter wheel, no issues there!
@mihaiserbanescu8676
3 ай бұрын
@@dapetdetective I was thinking to get the NRG short boss kit. I hope that will bring it back a bit to OEM spec.
@dapetdetective
3 ай бұрын
@@mihaiserbanescu8676 yeah that should work great and not much difference I’m sure