Just bought a miata 7 hours ago. Stayed up all night watching mod videos. This is BY FAR the most helpful video ive watched

@TheSundaeDrive

3 жыл бұрын

Really appreciate that feedback! We have another miata video coming out this week or next that should be helpful as well :)

@lilyhatake8213

3 жыл бұрын

SAME had mine 3 weeks now, best tutorial i've found

@rogergomez9972

Жыл бұрын

Haha same! Just bought mine two days ago and the horn isn’t working so I’m here trying to get it to work

Those round tabs are for the horn connection, sits behind hub and in turn you bend out that straight tab which then makes constant contact for the horn

@TheSundaeDrive

4 жыл бұрын

ahhh ok. Makes sense. Thanks!

@whitesox2624

4 жыл бұрын

Essentially what the paper clip is doing right?

@TheSundaeDrive

4 жыл бұрын

Yes. Not entirely sure how to get the other things too work but I guess I would just need to play with them and figure it out

Just wanted to let you know how helpful this video was. One of the single best tutorial videos I've seen on KZread. Installed a cheap Amazon hub, an NRG Quick Release, and a Momo Benetton F1 wheel last night in my NA. Frequently referenced back to this video during the installation. Salvaging the connector from the old wheel was genius and made for a very clean install. Thanks again!

I just watched about 20 videos on installing this hub with a working horn, this is by far the best solution. That paper clip idea was simple and very effective

@TheSundaeDrive

Жыл бұрын

Glad it helped!

Hard to imagine there will ever be a better tutorial than this. Thank you so much! I've subscribed! :)

just finished installing my first quick release, and i followed this vid step by step, and im thankful for a proper video👌

@TheSundaeDrive

Жыл бұрын

Great to hear!

Thank you guys I followed every step definitely the best tutorial I found.

@TheSundaeDrive

5 жыл бұрын

Awesome! Glad it helped!

THANK YOU! Everyone on here talking about getting under your car and adjusting the tie rods... The kid that installed the steering wheel on the car I bought had the white dot at at 10-o-clock instead of 12-o-clock. I knew there had to be an eaier fix than adjusting my tie rods.

Best video showing step by step iv seen about installing one of these

@TheSundaeDrive

3 жыл бұрын

Thanks! Just hope it helps :)

Perfect video thank you!!!!! Why can’t everyone make how to videos this good!!

You rule so much I was so hesitant but after watching this I cannot wait to tackle this

@TheSundaeDrive

Жыл бұрын

Glad to help!

I was so totally stumped with my horn lol thank you so much this helps a lot, gonna try fixing my messy job this weekend

@TheSundaeDrive

4 жыл бұрын

Lol glad it helped!

You’re goated for making install videos

the most helpful miata horn video!! thanks!!

@TheSundaeDrive

Жыл бұрын

Awesome! Glad it helped!

I know this Video is old but a GREAT walkthrough! Those rings are Grounding Rings not all horn buttons will ground nicely with all adapters or QR's.

i was looking for a way to get my horn to still work thank you so much!!!!!!!

Thank you for making this video

@TheSundaeDrive

4 жыл бұрын

No problem! Glad it helped!

My NRG steering wheel set just arrived and waiting for me to pick up from the post office...yay!!!! Gen 2.0 quick release and USPL steering wheel

@TheSundaeDrive

3 жыл бұрын

Woo! Enjoy

Awesome vid probably best one out there

@TheSundaeDrive

4 жыл бұрын

Thanks! :) We do at best to not leave anything out

Excellent video. Appreciate the quality of install!

@TheSundaeDrive

4 жыл бұрын

Thank you!

Great video very helpful gotta do it to my Miata once I get the chance

@TheSundaeDrive

Жыл бұрын

Glad it helped!

Thanks for the video man.

@TheSundaeDrive

Жыл бұрын

You got it!

Does removing the clock spring allow the short hub to not rub on the plastic steering column housing? I kept the clock spring and had to cut the plastic housing in order to allow the steering wheel to turn smoothly.

This is such a good video :)

@TheSundaeDrive

2 жыл бұрын

Glad it helped!

Actually done right. Thanks

@TheSundaeDrive

3 жыл бұрын

No problem!

How was it for the signals and wipers? I believe that steering wheel has 2.5 inch deep? Did you have to stretch your fingers out more ?

I'd vote that those are machine screws. Great video! I'm surprised how many people aren't using locktite on assemblies like this.

@TheSundaeDrive

2 жыл бұрын

Thanks! Locktite is often a good idea for sure!

Awesome tutorial, subd.

@TheSundaeDrive

3 жыл бұрын

Glad it was helpful!

I finally find a video where they say where this piece goes 13:33 I have a hyundai genesis but the videos do not teach very well how it gets, so I have to find other videos to understand

Great video thanks

@TheSundaeDrive

3 жыл бұрын

Hope it helps you out!

Any update on how well the stitching on the steering wheel is holding up ? I plan on buying the same one but in white

Does the Quick Release rattle when driving? The one installed on my NA when I purchased it rattled like HELL, and I want to avoid that.

In other words if you don’t want to do the whole thing with the harness you can just cut the end of the clock spring harness extend the red and green wire attach a paper clip to it to a bolt on the turn signal mechanism and make sure it hits the copper backing of the short hub correct?

Bolts have a smooth shank between the thread and the head, machine screws are threaded along their whole length, and regular screws have a pointy tip.

So Ik this video was a long time ago but what are all the things you need for the installation called. I have a wheel and a quick relese what else do I need ? And also do all quick relses work with all wheels ?

How does the spade connector trick work? Does it not matter what year Miata it is? I have a 96

"We didn't need these rings, we just assumed you were meant to ground with a paper clip" lol

@TheSundaeDrive

4 жыл бұрын

Lol fair 😅

This is a great video! One thing though I believe all the screws on the NA miata are JIS, not Phillips. If you use a Phillips driver on a really tight JIS fastener it will cam out and strip. I definitely recommend getting some JIS drivers for your Miatas!

@LanceBruce

2 ай бұрын

Yes, I came here to say the same. If you do any amount of work on these things, get the proper JIS tools, it'll save headaches in the long run

Definitely a bolt. Perfect definition.

@TheSundaeDrive

3 жыл бұрын

:)

Did you have to reconnect the ground wire you took off from the white clip?

How does it compare to the stock offset?

16:09 put one between the hub and quick release to create a ground tab for the horn wire. only used on certain setups.

hi i was just wondering if u half to put the silver mark on the top 14:38

just bought a 92 mx5 going to do this asap

@TheSundaeDrive

2 жыл бұрын

Enjoy!

I've looked st a few guides, and some kept the clock spring, while others removed it, what makes the difference?

@anthonyparks343

4 жыл бұрын

Pretty sure the clock spring is what automatically turns your turn signal off after you turn the wheel a certain amount. So if you remove it, your turn signals won't turn themselves off after you turn. I would recommend leaving it installed

@danyfry39946

3 жыл бұрын

Anthony Parks I removed my clock spring in my car and it still turns off my signals

@TheSundaeDrive

3 жыл бұрын

The turn signals in our buddy's Miata without issue

So what did you do with the 2 circular thin shims with the tabs sticking out of them?

@TheSundaeDrive

2 жыл бұрын

Nothing lol. Apparently they are for what we substituted a paper clip

There a wire coming out from spade connector? I have spade connector on but air bag light still flashing

so happy my AIRBAG light is off you are the best i love u

@TheSundaeDrive

4 жыл бұрын

Glad it helped!

@TheSundaeDrive

3 жыл бұрын

That may depend on the state/location. I'm not sure. You definitely lose safety with this and is intended for race applications.

Does the steering wheel come forward to the driver more than stock and by how much?

@TheSundaeDrive

4 жыл бұрын

I'm not positive but I asked our friend who owns the car and he said he thinks it moved it away just a tad but isn't positive either.

So the paper clip is connected to the red green wire and it is working as + am i right? And the wire at the hub works as - thank ypu for answer :)

@TheSundaeDrive

4 жыл бұрын

Yup! The hub is the ground connection

Does this kit move the wheel closer to the driver/create more leg room while driving?

@maiaaniceto5747

2 жыл бұрын

depends on if you get a wheel that sticks out more or less

thank you

@TheSundaeDrive

4 жыл бұрын

No problem! Glad it helped!

May not be relevant directly to quick release installation. But wonder if the car already have a racing hub installed and want to remove it before we can install the short hub. Any easy way to remove the racing hub after removing the nut? Struggled quick a bit but still won't able to pull out the racing hub.

@TheSundaeDrive

Жыл бұрын

Unfortunately I have not done that and it has been quite awhile since we shot this video so I'm not sure. Sorry I couldn't be more help with that :(

If you disconnect the clock spring which has the airbag wires, don't you then have your airbag warning light always on? isn't there a resistor that can be purchased?

@TheSundaeDrive

Жыл бұрын

We solved this by shorting it out on this car but that will vary from year to year. Most will probably need a resistor.

When I went to put my short hub on and crank the nut down The plastic housing around the steering column was pinched between the hub and started to deform.... You guys didn’t have a problem with this?

@hollyoldham3603

2 жыл бұрын

Did you figure out how to fix this?

when i fix the same setup the steering wheel is more harder to turn...how can i fix that,

Can this is same if i want do it to a 03 matrix?

Does this install keep from the Airbag buzzer and light from flashing and making noise? Or do you have a method to correct that? Great install video

@TheSundaeDrive

2 жыл бұрын

Glad to help! What we did kept the airbag off in this car. It may vary from car to car tho.

@brocksumpter2627

2 жыл бұрын

@@TheSundaeDrive I have a 95 NA8. I just heard the light and a beeping sound happens when the airbags disconnected.

Thx 🤟

@TheSundaeDrive

3 жыл бұрын

🤙

those "rings" are essentially why you didn't need that paperclip lol...You attach the wire to that tab and it functions as a wire with a round base ;)

@TheSundaeDrive

4 жыл бұрын

Thanks! I wish I could have found something to let us know that when in installing lol

@bombshelboy

4 жыл бұрын

@zchsomething you put them right next to each other and scratch up the area where they make contact/where the spade connects so it's bare metal. They should include 2 so you can make them slide against each other that way

@bombshelboy

4 жыл бұрын

@zchsomething sorry, I had an NA! The wire was red with a green stripe for mine (if it's the same)

@hunterdelgado2402

3 жыл бұрын

i know im digging up old stuff but im also kinda retarded, so that "ring that prevents the horn from spinning around" has a little slit in it, you attach a wire by just wrapping the copper around that ring?

@bombshelboy

3 жыл бұрын

@@hunterdelgado2402 look up a "crimp wire connector" and picture the cup styled ones slipping over those tabs ;)

The clock spring is essentially the wire and the paperclip but for the regular wheel

@TheSundaeDrive

2 жыл бұрын

Pretty good anology 👍👍

So if I did this whole process w out removing the clock spring part the horn would still work??

@TheSundaeDrive

2 жыл бұрын

As long as you did what we did your horn will still work 👍

The thing at the end u put in the hub and connect the wire as a ground

Is the wheel position in relatively the same place as the original boss? Thanks for the vid!

@TheSundaeDrive

2 жыл бұрын

It's similar but not exactly the same. I want to say it sat further away from the driver but not 100% sure. Don't drive it and it's been awhile lol

@fifielcoolio

2 жыл бұрын

@@TheSundaeDrive cheers

I just got a Miata and it has a Momo steering wheel, I would like to get a quick release for it. (The horn works on it) Will any quick release hub work with the wheel? And all the horn and airbag wiring should be done because I don’t have an airbag light and the horn works with the center button.

@TheSundaeDrive

4 жыл бұрын

I am not sure but someone else watching may know!

@JavierVillalobos

3 жыл бұрын

It's a SRK-160 short hub+ SRK-250BK quick release, there are clones on amazon as well. Good luck!

The plastic trim around the hub is too small on mine

Will my signal lights click back off when I make a turn ?

@TheSundaeDrive

3 жыл бұрын

No issues with that for our buddy's Miata

The flat rings could be the ground where you used a paper clip. The inner extrusion needs to be bent accordingly to make the proper contact. Let me know.

If I had to guess I would say Those 2 round plates might be used to connect horn wire to . Those plates would have constant contact on the part you used paper clips for .

@TheSundaeDrive

Жыл бұрын

Yes that is what they are for! A few have commented with that solution. Thanks!

This video seems like a good tutorial but I followed it step by step and my airbag light is still on somehow and my horn only works by moving the wheel and the button does absolutely nothing

This may sound like a dumb question but can the wheel and hub be used without the quick release?

@TheSundaeDrive

4 жыл бұрын

I don't believe so

@B0F

4 жыл бұрын

yeah you can. some people just run the hub without the quick release, especially when they have a dished wheel which makes it too close to them because of the quick release

for some reason the short hub is rubbing a lot on the back part and it’s hard to turn? help please

If I understand the wiring for your horn, the new wire/paperclip is +12v from the horn relay, and the hub/steering shaft is ground, and the horn button competes the path to ground to energize the relay. I have a '95 someone else modded a bunch including installing the nrg hub but they never got the horn working. I'm now trying to repair it and my steering shaft isn't grounded. I'm struggling to figure out why the shaft isn't a ground or maybe my understanding is off.

@natek4391

7 ай бұрын

Figured out it was just ball bearing grease was perfectly insulating the shaft from when I parked, turned wheel a tad and the ground came back.

@TheSundaeDrive

7 ай бұрын

Wow that's crazy. Had to be a fun one to figure out.

hey Great video ! and gorgeous wheel !!!🔥🤤 do you by chance know is there a kit for the w202 benz ???say a 1999 model

Those metal rings he mentioned is for hooking up the ground if you dont have a grund wire and instead put it straight on the hub as a ground instead

@TheSundaeDrive

Жыл бұрын

Thank you for that! A few others have commented regarding that as well. We know for next time!

Tried the paperclip thing. The good news is that the horn goes 'beep' when I hit the button. The bad news is the horn also goes beep when I turn the steering wheel left or right.

@TheSundaeDrive

3 жыл бұрын

lol It might take a little bit of playing with. Supposedly those rings that are included can be used like the paperclip to get the horn to work.

Between 8:00 and 8:06 where did the red wire come from????

Where do you get the headlight eyelids, I can't find them anywhere

@TheSundaeDrive

2 жыл бұрын

Not sure. It isn't our car

Those tabs at the end are for a easier ground connection

@TheSundaeDrive

4 жыл бұрын

Good to know!

The ring is for the ground

Paperclip not necessary.take out the contact ring from the hub adapter and run the wire through the hole and connect it to the hub disconnect power wire.more solid power connection compared to a paper which can potentially not make contact.

@TheSundaeDrive

4 жыл бұрын

We will have to try that next time. Thanks for the tip!

You didn’t use a hub?

has this 100% been proven to fit on an ND?

my paper clip came lose while driving around lots of curves - now it honks randomly - time to take it apart

Which gen nrg quick release is that?

@TheSundaeDrive

3 жыл бұрын

Gen 2.0

My horn will not turn on anymore??? It’s all plugged in right but idk what to do

@Paxizz

3 жыл бұрын

Me too.. Followed every step.. :/

How did you guys did the conector for the airbag light?

@TheSundaeDrive

3 жыл бұрын

We show it in the video. Shorting the connection worked for us but doesn't seem to work for everyone.

@aaronmartin5700

3 жыл бұрын

@@TheSundaeDrive yeah but how you did the spade connector thing i dont get that part so thay i can try it

What happens if I cut off the wires for the clock spring?

@JavierVillalobos

3 жыл бұрын

Nothing, but you need to be able to leave enough wiring to make connections for your airbag light or it will make a terrible noise and leave a airbag light on your dash. The wire that is red/grey stripe (some NA models idk for certain) will be your horn, you can make a male connection using some cheap wiring, then connect that single male wire to one of the connections on the quick release. Adversely if you don't care about little buzzing + the light for the airbag or plan on unplugging it then chop that shit. IG: reformedprize

@JavierVillalobos

3 жыл бұрын

sorry, and the other two wires that remain are the ground and airbag, you butt connect them and it shorts the two together OR you could soldering in a 1000 om resistor and be a proper engineer/electrician.

How did y’all get the ding in your quick release

@misteremellie

3 жыл бұрын

its the 2.0 nrg quick release that makes a ding when you put it on

@6lackRain

3 жыл бұрын

the metal quick releases only ding so of you got carbon fiber

I may be wrong but i feel like the silver piece is whats supposed to be there instead of the paperclip.

I have a question .. it can be installed in a 2004 Chevrolet TRAILBLAZER? .. blessings

@TheSundaeDrive

4 жыл бұрын

As long as the adapter is compatible it should be doable!

Followed this video exactly but now my dash lights and marker lights stay on even with the key off

@jessehamm7156

3 жыл бұрын

Any ideas on why this is happening?

i can’t figure out how to get the airbag harness off!!!! it was a very good video i’m not sure it might be stuck or something. anybody else?

@malicemotorsports

3 жыл бұрын

^ it won’t clip off.

What is the part number for the steering wheel?

@TheSundaeDrive

2 жыл бұрын

All the parts are linked to in the description :)

Screws thread into a part. A self tapping screw makes its own thread. A machine screw screws into a preformed thread in a part. A bolt screws into a nut.

@TheSundaeDrive

Жыл бұрын

love when people still comment about this and it reminds me of this job haha. thank you :)

looking for someone in Los Angeles that can do this if you have a suggestion

@TheSundaeDrive

2 жыл бұрын

I'm sure someone will comment with some suggestions for you! I don't know that area unfortunately.

That plate was for the horn

what is that plastic piece he is talking about at 10:48

@nickhall5349

Жыл бұрын

my clips are broken on that piece and was wondering if its a major deal, like if it has to be removed

It goes in between the hub adapter and quick release for ground connection to horn

Do I need the quick release

@TheSundaeDrive

3 жыл бұрын

Probably alternative methods for hooking it up. Quick release is nice tho. Only style connection we've used but some others can probably weigh in.