Wish more people would find this channel. He is very talented.

@salterclan

3 жыл бұрын

Totally agree. One of the better channels for general smithing and fun projects.

@stocky9218

3 жыл бұрын

Edit your comment and encourage people to like his vid cause your comment is top. Will get it recommended more 👍

@forgedbydragon9683

3 жыл бұрын

Agreed but at the same time I don't really enjoy watching him for some reason

@hazemzoma3363

3 жыл бұрын

Share the video and recommend channel

@arcticcarrot5932

3 жыл бұрын

As a former Canadian yes

Waiting for that pure elemental tungsten knife.

@matthewwilhelm8819

2 жыл бұрын

I played around with tungsten in mine it’s impossible I think

@onnokis5596

Жыл бұрын

@@matthewwilhelm8819 too much brittle

@alomejorqueno

5 ай бұрын

That would be one heavy knife. And not really good for knife stuff. I want to see it, though

I don't know why but I love the fact that the papers on your sketchbook are old and dirty... It brings the spirit of the blacksmith....

It’s not that it’s cracking it’s the titanium has a very high weld temp so it was just folding and making long thin waves that look like cracks if you haven’t worked with titanium much

@GoudaFetaExpandDong

3 жыл бұрын

How would you fix that? Heat it to a higher temperature? Or work with it only when it's at a higher temperature, not so much when it's cooled down slightly?

@stienogamez8296

3 жыл бұрын

@chris chontas they were cracks

@Lunas2525

3 жыл бұрын

@@stienogamez8296 no he is right he is not working it at the temps he needed you need to work titanium between white hot to yellow hot he was doing yellow to cherry like you do with steels when i was researching titanium i found references to needing to wear vision protective gear due to the brightness of the metal at temperature.

@jonquinn11

3 жыл бұрын

Strain rate too high, especially as it gets colder. Power hammer not the best thing to use. Hydraulic press with slower ram speed would be better. Also, some of that may have been a lap. Metal is getting an hour glass like shape. The short strokes from the power hammer you’re not working through thickness much, just the outer layers.

@Karl_Kampfwagen

3 жыл бұрын

It's a function of the Titanium work-hardening on the outside, and forming an Oxide layer that it refuses to get rid of without abrasive removal. Titanium is my favorite metal to work with, even though it's very strange to work with.

The white puffs coming from hammering the Ti is probably Titianium-Dioxide. It is so white that it is often used as a pigment. Love your work! 👍😁

Dude you should make a titanium folding knife. Titanium handle scales , titanium blade , maybe titanium washers and hardware? Love your videos bro keep doing what you do my dude.

@jimf1007

3 жыл бұрын

That'd be awsome. Idk of he has the tooling to be able to make a good one tho. Perhaps he can prove me wrong.. He's got the skills tho that's forsure

@euclidallglorytotheloglady5500

3 жыл бұрын

It would be great, but I wouldn't be surprised if he stays the hell away from using Ti for at least the next 10yrs.

@knifelife7777

3 жыл бұрын

Euclid AllGloryToTheLogLady haha yea I wouldn’t blame him after the frustration of this video. It would be a hell of a challenge though! It could even be a series of videos i would watch it!

@knifelife7777

3 жыл бұрын

Jim F he definitely does! Maybe he could make the pieces and send the handle, washers and hardware out for the milling and then assemble everything at the end. He could do the blade and the rough cuts at his shop.

@ivarlaupet8972

3 жыл бұрын

Jim F If not, he could do a collaboration with another KZreadr.

Damnnn where has this channel been hiding. Glad I found it

Doesn’t look like cracks, it looks more like folds like in the skin, that’s what it looks like to me

This is simply amazing. If good titanium/alloy stock wasn't as expensive (or I, so cheap), I would jump on a project like this. Instead, I am content to remain jealous.

so glad I found this channel. It is nice to see someone working with titanium regularly.

If you want a good knife out of titanium I would recommend getting SM-100 or sometimes called NiTiNOL. It's a 60-40 mix of nickel and titanium. It hardens to 62hrc and gets some beautiful colors when it's tempered!

@erikcourtney1834

3 жыл бұрын

Isn’t nitinol a memory forming metal? How would that work with forging or heat treating.

@jellyfish1433

3 жыл бұрын

@@erikcourtney1834 it probably wouldn't be the best material to forge, more of a stock removal material, but there is a way to harden it to 59-62hrc. I don't remember the exact protocol sadly. It's honestly a super cool material to work with and has some amazing colors after the HT process

@wane1393

3 жыл бұрын

I’ve always wanted to make a sword of nitinol but it rounds up quickly to $2000 for what $5 of tool steel is

@jellyfish1433

3 жыл бұрын

@@wane1393 it's definitely a lot more expensive than the O1 W2 A2 and 80crv2 that I use for my knives

@jonquinn11

3 жыл бұрын

That’s not considered titanium. I have heard of divers knives made out of beta titanium alloy. Maybe 15-3-3-3 or beta C? Not 6-4 for the blade

This channel is epic !

I've been waiting for your titanium knife! I'm satisfied now. Can't wait for the finished product

You have quickly become one of the few channels where I already click 'Like' right at the beginning of the video, because I know the content will be great. 👍

Use Diamond abrasives that we use in stone work. should be able to really cut with 50 grit diamond.

Holy mackerel!! When the process of making the knife costs 10x more than the blank stock.

I really like this project so far. Really cool!

Great job Tim , I really love your creativity and motivation. Thanks for sharing your wonderful experience 👍

BIGGER!!! It’s titanium! Make a huge sword! I mean.. that would be really cool to see a really light & strong, cartoonishly big sword.. but you do you.

Dude you are awesome!

Been waiting for a new one of these

It moves like jelly.. So clean when it gets hit

That's one massive scuba knife.

Love the work man I’m glad to have found your channel

How to set your self on fire with style part 2 hot knife boogaloo

At least another 4 belts, seeing the Ti Hammer used to help forged the Bowie Knife was neat!

Beautiful work too man..i loved the hammer too

This guy is making Sackin Metals some stonks

Titaniun, Surprised me the Hard work . Congratulations, you haver talent and courage.

Love the white sparks it throws when grinding. Keep up the great work from Montreal Canada.

This is going to be wicked ! Can’t wait to see this one done 🇨🇦🍻

For being young you have a lot of knowledge in blacksmithing. Can't wait to see it finished .I'm gonna say 9 belts .

You deserve more than 1 million followers

Aggressive project, but coming along nicely. Nice work Tim.

Holy crap, what a tough material!

“All the crack is gone” Crack heads: I know the feeling bro

@RubenKelevra

3 жыл бұрын

Yeah and he had no coke, too.

@brandonb1681

3 жыл бұрын

@@RubenKelevra So he "smacked" himself out of frustration.

yo man, awesome to see your channel grow!! Been watching you since the beginning! awesome work mate! Hope to be your size someday!

Love the videos Tim

Titanium rocks, I'm sure it is hard to work with but the end-product will be freaking awesome :-)

Hi Timothy. I find your channel very interesting and enjoyable. My dad was a blacksmith. All the best from the UK

Lama veramente fantastica!!! 💪💪💪💪 Lavoro incredibile 👍👍👍👍👍👍✌️✌️

BOO-E; and, you’re an incredible smith, brother...🤝🥃

Hola, no entiendo muy bien el idioma inglés, pero me encantó tu contenido: es relajante y me apasiona tu dedicación. Saludos desde Colombia 🇨🇴🇨🇴🇨🇴

New subscriber here. Found you by suggestion from Alec Steele. I rather enjoyed watching this and the time lapse sections were fun to watch as well. Going to be checking out your other content as well.

Idk why he doesnt have over 100k already like this is one of the channels that should be over 100k subs

I've just got into black smithing and built a foundry. I'm loving it and it's great to find a small channel forging with quality content.

a dozen minimum. looking good can't wait to see it done

Awesome video. Just a quick advice, you should get welding glasses, the sparks from Titanium are almost bright as the sun, it's dangerous to grind for long periods of time

@shayanthis

3 жыл бұрын

Bolle and uvex both make "sunglasses" for welding applications. They aren't suitable for use as welding goggles, but more for use by offsiders, TAs, etc. They are pretty damn good as sunglasses as well.

@ratapotamus

3 жыл бұрын

Thanks for that. That was my question

Titanium keeps a lot more of its strength at typical steel forging temperature. Either increase temperature or use more pressure. Titanium is a lot more reactive than steel and the oxide it forms is really hard. In aerospace forging the pieces are normally etched afterwards to remove that oxide layer because it wears any machining tools to bits.

Cant believe you have only 45k subs, great content!

just wanted to say, you found the perfect music for this video.

Bro you need to wear a mask and that titanium can ignite spontaneously when a dust like that. It is hazardous also.

@It-b-Blair

3 жыл бұрын

A B 😳🤯

@danielwurmer2266

3 жыл бұрын

He is wearing a mask...

@ruthless_roast5869

3 жыл бұрын

I used to forge huge billots of titanium in my old forge plant, never heard anything on wearing a mask. Unless youre talking about grinding. I have no knowledge with that maybe my forge plant wasnt knowledgeable on forging titanium since we didnt do it often

@jonquinn11

3 жыл бұрын

No, the dust is no more hazardous than anything else to your body. In fact Ti is basically neutral to your body. And guess what, TiO2 is in your toothpaste to make it white. The scale is not pyrophoric. It will not spontaneously combust. It needs an ignition source, even if it’s just grinding sparks. Grinding swarf can be dangerous from the fire hazard standpoint.

Go from talking about coke in the last video, now you talking about crack? love it :)

Love to watch you doing what you do.... wish I could do that but my state has a lot of regs and getting the permits is a chore to itself....

I just want to say i love your shop and the work you do. Not to be like the people who try to tell you how to do what you make a living at, but your voice is kinda soft and the music loud, I wear headphones so wife can enjoy what she does without me disturbing her. anyway love your work. sub. here right now.

Love from India 🇮🇳👍

Damn, that anvil is loud!

Never thought endmills would beat belts in sheer willpower

@mndlessdrwer

3 жыл бұрын

Sintered carbide end mills are relatively inexpensive and very, very hard.

I shy away from grinding a lot of material off my titanium blades because it takes so long i usually machine most of the material off but like your idea of slowing the belt down I’m gonna have to try that thanks brother maybe we can collaborate on a titanium knife one day

Invest in a large industrial abrasive wheel grinder. 12-14”. Proper wheels and you will be bang ahead for time grinding and cost of abrasive. Or diamond.

@jonquinn11

3 жыл бұрын

Or mill it.

waiting for part 2

Is he using his titanium hammer to forge a titanium knife?

@arctic_angel7408

3 жыл бұрын

yes

@Karmaikaze

3 жыл бұрын

He's a absolute mad lad

@mareli82

3 жыл бұрын

yes

Love the channel! Isn’t the highest HRC you can get out of titanium about 45? This will be a nice knife-shaped object, but will it really be a functional knife?

It is looking awesome, l don't know if one could make a knife like this without a big power hammer. I looks really hard to move material. Love your channel.

hi Im really enjoying your videos, Im from Brazil btw

Heh. Sackin Metals is right down the street from me. Also, ceramic belts need to be run at high speed with a fair amount of force applied or else the sharp edges get rounded over instead of breaking and creating more new sharp edges.

Lookin Forward to see this Blade finished and how or if your going to temper it...Also Curious if it is going to chip easy... As for the Ceramic belts i say 6 maybe more...Titanium Bowie Knife enjoyed watching this... Thumbs Up

6 more belts! That’s my guess. Nice video. Thank you!

Annealing the titanium between grinds helps it get softer. It work hardens very quickly.

Nice

3:03 that cameo tho

I’ve made a few smaller Ti blades and my guess for that beast will be 9 at a minimum for a somewhat finish grind. Depends on the level of finish. 220 was the best I got. Best of luck, it’s looks awesome.

Now I am far from a metallurgist and any metallurgist who reads this I'd be interested to know your take on this but in relation to the cracks you were experiencing at first, my guess is that titanium might be really sensitive to forging temperatures and maybe you were just barely not getting it hot enough or maybe just barely to hot. But regardless of all that this is an awesome project and I'm really happy to be brought along on this process. It's my understanding that titanium won't hold an edge as well as steel but I'd still do this project if I had the means. Oh and I guess 8 more belts.

I'm going to look for an update video for this. I want to see how your various titanium tools, as well as the other non-ferrous metal pieces, are faring over time.

The first time you hit the titanium bar you folded the sides, then when you switched the side you wanted to hammer it flattened the folded waves and actually made it go deeper, I suppose tho, seems like the most logic answer

Dude your very talented, you should consider making a video with Alec Steele , for sure you'd co,e up with crazy awesome videos and projects

I would have said another 20, but I also know this is a series

Just keep anything containing nickel away from the blade. Titanium loves galvanic corrosion with nickel. Looks good so far.

I have just a little knowledge about the subject but i'm really grateful for your effort to bring this content! Can someone explain to me why it's so hard to work with titanium and what are the advantages of the final product in comparison to a regular steel knife?

Good. The rod at the initial forging needs more heat I believe. The core of the rod not hot enough as outer?? The temperature difference between core and outer side might be the reason for fissure at the time of initial forging. As the stock got relatively thinner the problem was not noticed. May be stress difference because of temperature difference within the rod. Make it white hot. Camera exposure variation considered. Nice.

Watching this makes me want a titanium sword like a katana or something that would be dope

Totality ti stiletto or tactacal mechanical folder, belts 20 to 80 total to finish the knife, bone scaled handle...

Hmmm... 3 more belts. Good luck!

Great Idea, Im a hunter, so thinking about a bush knife and camp axe. Which round bar did you use from Sackin, not knowing anything about TI i am lost for specific selection for my intended use. Thanks

Very impressive job Tim, but wanted to know if you guys have available circular shape on this metal.

The cracking doesnt come only from the fatique. When the workpiece getting thinner it cools down faster. Titanium when its getting orange'ish starts to do the fatique thingy with the cracks. Bright yellow as the Sun is the way to go. On the hammer it didnt do that that much , since the hammer was a more "massive chunk".

They looked like cold shuts to me, less like cracks.

I think the lower wheel on the belt sander is the intended spot to grind on those belt grinders, isn't it? The soft back is better for the belt too, keeping it cooler with no back friction

Glad to see you’re using the titanium hammer! Ps. Where’s Martin? I miss his sobering gravity to your enthusiasm 😆

My 2x72 is driven by a 3hp donk, I run it at about 33% on the VFD, that keeps the Ti spark down a lot, I use 50gt Norton Blaze belts, I have no problem grinding Ti now, although I much prefer to machine it, I find that it feels like it"slips" against the belt, whereas, blade steel, stays in the grind much better??. Good luck, Scott.

Will titanium harden enough to keep an edge?

Not sure how I found your channel exactly. It showed up somewhere probablu because I watch Alec Steeles channel. I gotta say... I like the couple videos I've seen so far. Seem like a cool dude. I've subscribed obviously.

Your anvil sounds nice man how is it set up?

12 belts ultra conservative, 18 realistically. Last time I worked with titanium, I blew through 4 *good* ceramic flap wheels in 45 minutes. Also not a fan of holding my working metal bare handed, even with just a grinder around. TIG gloves if you've got nothing else around, but with Ti, I "armor up" with full length MIG gloves, leather apron, auto-darkening welding helmet, etc. I've seen a workpiece go from perfect to a nanosecond away from bursting into flame while mildly chasing perfection.

Always wanted a titanium sword. It is the Beskar in real life

"Let's get the grinder out!" Nik Blackhurst from Bad Obsession Motorsport: *heavy breathing*

My best guess as to the mystery cracks on the titanium billet on the powere hammer is that titanium is a poor conductor, so it was probably unable to keep the surface quite as hot as the center of the billet and was unable to bring heat to the surface of the billet between hammer blows causing the effect.

Using the titanium hammer on the knife... noice

To heat treat and temper titanium you just normalize the piece of titanium and it hardens by room temperature... so I've heard and titanium does not make a good blade it will dull out pretty quickly sadly that is true

@masrurbule2868

3 жыл бұрын

But its a magical feeling to hold in your hand

@Butterflyknifes1

3 жыл бұрын

@Ngiplong NGIPLONG the only thing it will be probably be good at cutting its fruits and vegetables

Titanium isn't supposed to be heated, welded or worked in the presence of Oxygen - Might be of value to check out some of the information from what Lockheed Martin's "Skunk Works" found as they manufactured the frame and skin of the YF-12A and SR-71.

@ats440you

2 жыл бұрын

Correct. For knife blades I would suggest using bar or sheet, cutting out the profile and simply grind the bevels. For a hard working edge, weld titanium carbide on the cutting edge. A few custom Knifemakers work in this way.