How to Pull Dent With Stud Welder
Автокөліктер мен көлік құралдары
How to fix and pull dents with Harbor Freight Stud Welder Dent Repair Kit. In this video I am pulling dents on my 1969 C20 pickup the old school way stud welder and slide hammer.
Products
Stud Welder: www.harborfreight.com/stud-we...
Grinder: amzn.to/3CLN4Vk
Wire wheel: amzn.to/3FaQH9t
Orbital Sander: amzn.to/3CR61Gb
80 grit 6” orbital sand paper: amzn.to/3kQt5yM
Block sander: www.harborfreight.com/17-inch...
Block sand paper: www.harborfreight.com/2-34-in...
Bondo: amzn.to/3F0FJmI
Spot filler: amzn.to/3uk8AgM
-----------------------------------------------------------------------------------------------------------
Chapters
0:00 Intro
0:28 Prepping Dent Location
3:10 Using Stud Welder
6:48 Using Slide Hammer
9:34 Finishing up and Final
10:30 Close
Don't Forget to Like, Comment and Subscribe!
-----------------------------------------------------------------------------------------------------------
Info:
KZread Channel: / chrisncars
Website: chrisncars.com/
Mail: ChrisNCars.Mail@gmail.com
Video: • How to Pull Dent With ...
This is one of many restoration videos I have made. More can be found here:
• WorkiN on Cars
-----------------------------------------------------------------------------------------------------------
Music:
Fleas - Dyalla
Benji - Dyalla
#ChrisNCars #CarDIY #AutoBody
-----------------------------------------------------------------------------------------------------------
Disclaimer:
Due to factors beyond the control of Chris N’ Cars, I cannot guarantee against improper use or unauthorized modifications of this information. Chris N’ Cars assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Chris N’ Cars recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Chris N’ Cars, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Chris N’ Cars.
Пікірлер: 30
Nice demo
@ChrisNCars
2 жыл бұрын
Thanks for the comment hope it helped.
Thank you for the video. You're the only one that actually shows how to use it properly!
Hey thanks Chris!
Hold the puller on the stud snug and tap around the outer edge and that helps.
There was no need to unhook the battery on that truck because it doesn't have a computer in it and I've been doing paint and body work for over 21 years and even on new cars and trucks that had a computer in them I didn't ever unhook the battery when I welded panels on the vehicle. And done no damage to the computer. I don't know where it came from. But when the ground from the welder is close to the spot that you are welding you don't have to worry about anything. Now when I say close I mean you can have it somewhere around 2 feet. I've welded next to the computer with the battery hooked up with no problems. But if you want to just for your own piece of mind than that's fine. But it's not necessary
I'm looking at buying the HF Stud Welder and this answered many of my questions. Thanks Chris!
@ChrisNCars
2 жыл бұрын
Excellent! Glad it helped.
Great information, thanks for taking the time to do an excellent demonstration.
Thorough demonstration using this weld gun. I picked one up to use soon. Thank you
Heading out to get one now lol ! Thanks for a great video demonstration
Looks good sir .
Guys buy unispotter 2.2 mm studs..they will work every time. Also Vevor sells a nice dent puller for a bit more that has a hard case and alot of kool different pull tabs. But stop using the hf studs n get goood ones
👍👍 my car needs this.
@ChrisNCars
2 жыл бұрын
Pretty easy! That’s why I made the video, ha! Thanks for the comment.
awesome!
Thanks dude. That was nicely explained. Now do I want to tackle my daughters mash up job???
@ChrisNCars
Жыл бұрын
😬 depends how bad it is ha!
Remember when that wheel on that dent puller goes out they do not have replacement Wheels to put on those pullers.
It's the stud gun that's crap. I have same one and always had studs pull off..with more expensive guns it is rare to have that happen
@rolandwallick844
Жыл бұрын
ive never had a stud pull off maybe you use yours more than me but mine works fine
Can I get the info in what type or brand of body filler
@ChrisNCars
Жыл бұрын
Just the typical bondo
i know im late to the tutorial hahaha but i did have the question, if your not worried about damaging the paint is it necessary to sand it down like you did?
@ChrisNCars
Жыл бұрын
There’s paint less dent pullers that won’t ruin paint. Need to put a vide together on how to use one 👍. This method you have to sand because it’s welding, can’t weld those studs ontop of paint.
@aidenog7380
Жыл бұрын
It needs a ground to work the tip touches bare steel and that’s the ground no ground no weld
Unless that paintwork is damaged, next time try using glue tabs and a sliding hammer.
Why not just put filler over that den
@ChrisNCars
21 күн бұрын
Too much filler cracks over time
To much talking