The one thing all body men possess is patience! I have very little so my body work is usually sub par! Great video, J in Albuquerque.

back in the 60s and 70s and even 80s cars had so much metal on them all we had was screw on dent puller and hooks. you drilled holes to pull dents and then slapped bondo. now they are so thin we need these spot welders.

congratulations, teaching someone how to do something, is honorable, nice video.

@HowToPaintYourCar

7 жыл бұрын

Thanks bud

This is a great detailed video, the fact that you could repair that hood without buying a new one, shows the skills man, good shit.

Finally someone on youtube who knows how to mix filler properly!

@HowToPaintYourCar

Жыл бұрын

Thank you buddy!! Get a free training and know "How To Spray Like a PRO Without Orange Peel, Dry Paint, Nasty Runs & Tiger Striping by Modeling The 5-Step R.A.D.S. Paint Formula!" www.radspaintformula.com/rads

Nice videos Tony , I learned body work watching your videos, Im a Member also. I fixed my brother in laws Prius that had dents and scratches all over the car, The body shop wanted to charge him over 2K for the work. Good job

@HowToPaintYourCar

7 жыл бұрын

That is awesome Jamie! Keep me posted ok!

Thanks, Tony. Another great video, as usual!!!

always a fortune of good advice on this channel

Shout out to the Marine Corps sticker in the back glass!

This is the best way to pull out dents! ive tried with glue gun and tabs, and even welded on M5 screws on a volvo rear quarter that had been banged up! (Dont got this machine that you have!) Got my dents out! ;)

@HowToPaintYourCar

7 жыл бұрын

cool

Quality time with GODFATHER Good work!

I love your videos man Awsome I think your a good teacher it is cool how you were teaching your god father and you stayed patient thank you For the lessons 👍

What a Great Learning Video! Good Job 👍😉🇨🇦

@HowToPaintYourCar

2 ай бұрын

Thank you 🤗 Check out our LABAP VIP Program, know how to paint like a PRO and get your free manual at learnautobodyandpaint.com

Excellent demonstration! Thank you!

@HowToPaintYourCar

5 жыл бұрын

Thanks Eugen! Don't forget to grab your free manual if you still haven't: learnautobodyandpaint.com/free-autobody-manual

Great work Tony you explain it very well in a nice calm tone voice you are a master body man love the vids so beautiful there in Hawaii always wanted to vacation there or live there is it hard to start a business in Hawaii keep up with the great videos thank you

That machine is excellent, the less filler the better.

Dent on aluminium body more hard then standard metal..good job bro..

oh man.... you're such a blessing... thanks Bro.

@HowToPaintYourCar

7 жыл бұрын

Glad you like it!

Cool tool i have one and i am going to use it tommorow the only con is the studs are very expensive

Great video I’m trying to learn more and you explained things really well thanks!

@HowToPaintYourCar

4 жыл бұрын

Matt's Model: Check out VIP and see how it can help you more with your car projects! www.learnautobodyandpaint.com/vip-offer/

Great video, I have a rear quarter panel to repair on my truck, I will be now buying a stud welder.

@HowToPaintYourCar

5 жыл бұрын

Awesome man!

Nice

Just my opinion- I would spread the Bondo at least six inches beyond the damage so it will blend easily.

Nice video!

good work

You’re a great teacher man . Great info output I painted my racing boat my daughters atv and a few more things .. thanks to you I’m still learning new things can you tell me more about the grinding you do what kind of wheels do you use .?

@HowToPaintYourCar

5 жыл бұрын

Fidel Cordova thanks :) need to head on over to the site download the free autobody manual that I give away. Then you need to check out VIP we have over 100 hours of step by step info in there for you!

good

Very informative! Thank you. Hint I use the old 1800s irons that were he heated to iron clothes. I find at flea markets. Would work great for your backing.

@andrewerickson6690

10 ай бұрын

Great idea thanks

Buy parts? This is free. Anyway remember also that this is rear quarter on an old-er dodge truck. You pull that hard on some panels or doors and it gives a lot easier.

I’m using the same gun but the studs keep pulling through the metal creating a small hole. It’s obviously thin metal. I’m worried a mig welder will burn a bigger hole now.

Where can I get a slide hammer locked that

thanks for your time to show us how to get that dent out also how to use bondo can wait for the next part . keep up the good work hope one day I will be able to be good as you i see you are quick and neat 👍👍👍👍....O.G 😎 1042

@HowToPaintYourCar

7 жыл бұрын

No problem thank you more for the support :)

greeting from me, You R a good lecturer, waaw

@HowToPaintYourCar

3 жыл бұрын

Wow, thank you

Wack it back I've learned something today😂😂😂👌✌

Where can I get a slot hammer like that

bogus work not propper safe dear... try wurth air clutch puller... and do spot weld clipping then pull it...I think this is a good once afterall

I don't know because i feel like this is supposed to be something your god father should be teaching you but its wonderful when you're the one teaching a older person though :D

My stud welder has a smaller can wheel in the slide hammer

Hey howzit How do you choose location of where to weld pins?? Are you going on the line or at the lowest point of dent?

@smithfoxe

9 күн бұрын

I’m here to find this out as well.

@Corolla_Beau

9 күн бұрын

@@smithfoxe I figured that you do it reverse, as if you were watching a video of a dent made in rewind, you do have to hammer it still but that’s what I got with doing a few major dents. If you just weld/pull from the deepest point it won’t come all the way out and create mini dents/warps so best bet is to start some places in medium depth of the dent and then on the deepest points l, and then to clean up pull the body lines last. Best I can describe it with what I’ve done so far, but as usual, no help no responses, so I’m sure there are better techniques but get it done however you can I suppose, every dent is different there’s no one way to do all.🤙🏼

How much time between coats?

great video ! i wish someone can train me like that !

@HowToPaintYourCar

4 жыл бұрын

We have a VIP course that you might want to check out man. vip.learnautobodyandpaint.com/exclusivevip

they make a attachment to stud weld for migs too

I think I would've replaced that hood with a cheap one from the junkyard with no damage.

@HowToPaintYourCar

4 жыл бұрын

to each his own brother!

Do you need to to disconnect car battery before using or will it effect anything?

@HowToPaintYourCar

10 күн бұрын

Hey Man! By disconnecting the battery before using a stud welder, you reduce the risk of damaging the vehicle's electronics and ensure a safer working environment. Know more tips and tricks and check out our VIP Program at vip.learnautobodyandpaint.com/home

I like to spray the bare metal panel first with Primer, so it's sealed, I find the body filler sometimes lifts and starts to rust between filler and metal, I Primer first then put filler on Primer, then sand the Primer again then final paint. Etchit primer, I hate rust.

@gerardosoto1325

3 жыл бұрын

You must be doing something wrong with your body filler because it is actually recommended that you use body filler on metal only, but puddy can go on primer as long as the surface is scuffed

How do you stop the weld pins from snaping off the car when dent pulling

Would it be possible for me to send you a couple pics of a dented quarter panel and you let me know if it would be possible to pull out with the weld studs?

@HowToPaintYourCar

9 ай бұрын

Hey Man! Are you a LABAP VIP member? Check out our blog about Dent Repair Demo Using Grinder and Stud Welder Gun www.learnautobodyandpaint.com/live-dent-repair-demo-using-grinder-stud-welder-gun-plus-qa/ and you may also send an email at ninjasupport@learnautobodyandpaint.com

is there many different colors of hardener ???

Wow that's a lot of body filler

shoul i remove the battery before using that tool or not?

@theflyingdutchman787

3 жыл бұрын

Using the stud welder won’t affect the electrical system whatsoever. The current is localized to its working area

Does it work on aluminum

Do you have to grind off all the galvanization (aka zinc coating) on the sheet metal before using the stud welder?

@devoywilliams5549

6 жыл бұрын

yea you can only weld to bare metal

So i was using a slide hammer that has a tip that welds on and some guys in a facebook group said to put pressure and to tap the crown instead of ligthly tapping with the slide hammer. Can i send you the video so you can see?

Can the studs be reused?

Hey Boss, everything looks good but you definitely have to prime that surface before putting bondo down, or its gonna rot from underneath

What gun are you using because I've had bad luck they don't seem to last long

@HowToPaintYourCar

3 жыл бұрын

Check out Zoolaa.com I use the ATOM X27 a lot. It’s a great spray gun!

@hectorcalderon3011

3 жыл бұрын

@@HowToPaintYourCar sorry I meant the stud gun

i need to do this to my dads 2011 dts that some punks ran into and i wanna suprise him and have door done in the next few wks

@HowToPaintYourCar

4 жыл бұрын

Adam, check out VIP and see how it can help you with your dad's car! www.learnautobodyandpaint.com/vip-offer/ Best of luck!

I never could get my stud welder to work on the Chevy corvettes. They just wouldn't stick for some reason

@jakerene3762

4 жыл бұрын

I could never get to bare metal on mine either 😂🤣

Can i use stud welding instead of oxy actelene when metal shrink and became like can

So my brother was backing a trailer up and Jack knifed it and crushed the corner of my bed under the taillight... It's really bad. My question is do I have to get a replacement panel or count I pull in and bomdo it?

@bobblack3870

6 жыл бұрын

Corner of the bed or the fender below the light? Or both? If you crushed the corner of a cardboard box, could you straighten it? The answer is not likely. You must "reverse" the damage in the same way it occurred. When you have multiple pieces of sheet metal coming together, repair may require professionals. Otherwise shop around for a complete back end or panel (as required). Bondo should never be more than 1/4" thick if you want it to last.

Question... can I weld two metal shade, one tap over the other with it. Like a spot welders? Thanks

@HowToPaintYourCar

6 жыл бұрын

I am not sure what you are asking.

how much would you charge me to paint my 72 riviera root beer pearl? you could use it for one of your videos too

Can I purchase nails as required from somewhere

@HowToPaintYourCar

Ай бұрын

You can purchase it on Ebay, amazon or nearest auto body shops stores near you Man. Grab our VIP Program trial and get Free gunbudd(will pay for the gunbudd you shoulder the shipping) you will get access to our auto body and paint course vip.learnautobodyandpaint.com/free-gb-offer-a?fbclid=IwZXh0bgNhZW0CMTAAAR38aOV3OmSW6xcSXN7jq55QYp4t617-UnXvCRHtnuVJUiAlLMVrqhCd1V4_aem_GQphCjwl_n7fDF3I2IrNzw

Is it better to use the 3mm or 2mm studs?

Great video. Just picked up my stud gun during a HF Tent sale. I have a crease in my rear truck fender, so this is good stuff. Is it not easy to hammer from behind, inside the wheel well, or is this just easier?

@HowToPaintYourCar

7 жыл бұрын

It was a dual wall, so from inside would just damage the other wall... :)

hi tony

Why do you hammer when he pulls with the puller? I would like to know what's the theory behind it?

@hardkore360

7 жыл бұрын

Ronald Almendarez it stiffens the metal so its not left flexible

@ronniebuicks5569

7 жыл бұрын

hardkore360 they thanks man, have a blessed Sunday.

@bobblack3870

6 жыл бұрын

If it could be done perfectly, you want the hammer to hit at the same time the slide hits. That is why he is trying to hammer very frequently. It is just by chance that with 5 slides, the hammer might be synchronized with the hammer a couple of times - that's when progress is made. It's all about setting up the desired shape.

Do you spray any epoxy primer or treatment on the metal before you fill it?

@horaciomartinez2915

6 жыл бұрын

Definitely should or else its gonna rot under the bondo

What are you building there? Need another gallon? Holy crap

Hello i want to paint my car and the paint on it is in good shape, no dents or deep scratches and i was wondering how much i would need to sand it before painting? Would i only need to sand away the clear on the existing paint? Would i need to primer it as well? I was planning on using a single stage acrylic urethane. Any feedback would be great thank you.

@rockdawg1467

7 жыл бұрын

you have to sand the clear coat down to paint and then make sure to properly mask the car and clean the paint and all jams and seal the old paint to avoid the chemicals reacting with one another and dry and prime and sand primer with 600-800 check for any inperfections and clean again blow any dust of car or truck and you can repaint with the single stage just make sure your using proper temp reducer good luck

@wyattalvarez6327

7 жыл бұрын

thank you!

@rockdawg1467

7 жыл бұрын

Your welcome

is that aluminum panel?

@HowToPaintYourCar

7 жыл бұрын

No, steel.

how much you used body filler on that hood you could of purchased one from junkyard

cool, i paid for the autobody course but i see all the same videos are on youtube! lol

@HowToFlipCars

6 жыл бұрын

ThisISETHANBRADBERRY! It’s not the same at all! Lol when did you join my friend? Did you register for the new membership site? Something is wrong. Contact support and tell them you want access to the new membership site!! Keep me posted buddy

@MrFreeze79

6 жыл бұрын

heyyyyy tony@!!!! i just joined maybe a few weeks ago to VIP. so far liking the site, lots of good learning. I just have to say, you have matured, but damn dude you don't age at all wth is up with that! stay young man, thanks!

some heat would be good

Where you buy your stud welder gun?

@HowToPaintYourCar

4 жыл бұрын

Bought it a while back.. try Amazon

How did it turn out?

@HowToPaintYourCar

7 жыл бұрын

SWEET!

@HowToPaintYourCar

7 жыл бұрын

Yes sir!

You look too much like Kirk Hammett in the 90's

@HowToPaintYourCar

7 жыл бұрын

I just need some long hair! lol.

5:15, a couple dollys would help you a bunch man..

@HowToPaintYourCar

Жыл бұрын

It was dual layer couldn’t get to it from the back.

@jhenson5168

Жыл бұрын

@@HowToPaintYourCar yeah you can. I’m doing now on a f350. Just need the right dolly

Good stuff, but hopefully your bondo spreading has improved..

@OfficialCarlosGarciaAceves

5 жыл бұрын

It's the end result right!

Good work, but I’d much rather have my car fixed with sheet metal and a wire feed

@gerardosoto1325

3 жыл бұрын

Damn what they fixing? Rust? This is the way to pull dent besides using hammer and dolly don't know what kinda repairs you need lol

Wouldn't be pulling the studs out if you knew how to use an actual slide hammer properly.

@HowToPaintYourCar

4 жыл бұрын

Why don’t you make a video upload it and show us…

That s not a proper repair first of all you don't grind off medal you cAn use a plastic roll out for that second using stud gun you pull from outside going to the deep spot and you don't hit the slide hammer back so you won't create a high spot points you u just pull one good pull and keep ur hand tight and help hitting the regular hammer around it

That shit is mangled.

@ngstahl

7 жыл бұрын

Just watching a couple guys that have no clue what they are doing.

@ultrainstinct8061

7 жыл бұрын

ngstahl and of course you do.

i do not like peper pay

Go to the junk yard and buy a hood, Jesus

@HowToPaintYourCar

7 жыл бұрын

Nah..

@alec4672

6 жыл бұрын

Why not just do the hood while doing everything else

@swiftWord

6 жыл бұрын

Hell yeah...I got one straight as an arrow from LKQ for $69

@jeepmoab1

6 жыл бұрын

This way is a lot more fun and satisfying....anyone can go buy a new one.

@Just-a-girl

6 жыл бұрын

Hmm, not a hood.

I once repaired something like this with just filler. There was like over 2 pounds of filler on it lmao. I did end up looking very good though, guy who bought it didn't even spot it.

@bobblack3870

6 жыл бұрын

I feel sorry for your buyer. With time he will know what you have done - his vehicle will tell him, plus you deceived him - because it sounds like you did not tell him. Not funny.

@Isaiah-ft5nx

2 жыл бұрын

You’re what we call a butcher.