How to Program A Chevrolet Malibu Smart Key Remote Fob 2013 - 2016
Автокөліктер мен көлік құралдары
A step by step video on how to program a smart key remote fob to a 2013 - 2016 Chevrolet Malibu.
More free DIY programming instructions available at www.ProgramYourRemote.com
1. Using the driver's door, turn the key counterclockwise to the unlock position five times within 10 seconds.The Driver Information Center(DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. The DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). Remaining remote key fobs can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.
4. Place the new smart key fob in the transmitter pocket in the center console .
5. Press the ENGINE START/STOP button. When the transmitter is programmed, the DIC display will show that it is ready to program the next remote key fob.
6. Remove the smart key fob from the transmitter pocket and press unlock or lock on the transmitter.
To program additional transmitters, repeat Steps 4-6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
Пікірлер: 333
Omg you posted this a few years ago and saved me today. I changed the remote batteries on this newer car and freaked out when I couldn’t open it. Almost had to call the dealership and pay an arm and a leg just to reprogram it. So thankful! 🙏🏼
@PYR-Auto
Жыл бұрын
Glad it helped
Really good info that'll save ppl big bucks. I had a 21 y.o. Blazer which used a key for entry and for ignition. Recently bought a 2017 malibu 2 months ago and using a fob and push button start is so strange to me. I've been binging on malibu video's to learn what all the buttons do and all the features. Miss my blazer; life was much simpler. Appreciate you and others making helpful video's. Thanks so much! 👍
@PYR-Auto
3 жыл бұрын
You're Welcome! Glad it helped!
Thank you... 2017 Malibu car went dead out of know where, and after looking and looking, to find away to get her back and on... with your time and respect, I was able to get her on... THANKS...
@PYR-Auto
3 жыл бұрын
Glad it helped!
Definitely works. Simple and precise. Thanks so much!
@PYR-Auto
Жыл бұрын
You're Welcome!
well done video ,it can not be explained more easier than the way you did it .thank you for saving a lot of money for who ever ran to a key fob situation (lost or damage) and end by copy what you did ,very kind man wishing you the best in your life sir.
@PYR-Auto
2 жыл бұрын
Thank You! Glad it helped
@WithlovefromTaminko
Жыл бұрын
me...I was the one who had the issue saved me a ton of money!! I flexed so hard when I went to pick up my fob! They told me I had to use their software...I went on KZread and VOILA!!!
This worked good for my 2017 Chevy Malibu Premier! Took like 40mins to do, wish it was a faster process!!!! I had one transmitter and 2 cut keys. Just bought a transmitter from ebay for about $35, did this process and worked like a charm. Will need to reprogram new and your old key! If not the auto theft deterrent system message will pop up.
@xxsilhouettesxx309
2 күн бұрын
I think ur about to be a life saver ima update in 30 mins 😭
You saved me at least $200 for a 2nd key. Thank you for this video.
@PYR-Auto
3 жыл бұрын
Awesome, glad it helped!
@ericlee3456
3 жыл бұрын
@@PYR-Auto my alarm goes off😩 is there another way
@RunYaBagUp_C
Жыл бұрын
You got one key to work? If you could please respond
@JonnySpectacular
Жыл бұрын
@@RunYaBagUp_C I don't own the car but I ordered the key from Amazon, the AC Delco key. I just went step for step what PYR showed. I had no issues when I programmed them.
@RunYaBagUp_C
Жыл бұрын
@@JonnySpectacular damn so that means im going to have to grab another key and what’s so I crazy is I was doing these steps and then locked my key in the car so I’m shit out of luck cause of the holidays 🤦🏽♂️
As a locksmith i freakin' love your website, thanks a lot for the resource. Yeah I still print out the instructions on some of those toyotas lol
@PYR-Auto
10 ай бұрын
Nice! Glad it helps
Took me 4 times on my 2018 Malibu but it finally worked. Thanks for saving me 200.00
@PYR-Auto
3 жыл бұрын
You’re Welcome! Glad you got it to work
@Amvndah
3 жыл бұрын
Please help me lol I’m so lost
@SRT_Tom
3 жыл бұрын
You have a Malibu LS? And you did it for remote start?
@Conflictosocial
Жыл бұрын
@@SRT_Tom i Have a 2018 remote start don’t know how to actívate the second key
Think you! You saved me some serious coin the dealer ship was talking around $600! for a new key phone and programming! When they charge that much why would they want to make quality vehicles, it's a damn shame
@PYR-Auto
2 жыл бұрын
Glad it helped
Absolutely a life saver!!
@PYR-Auto
3 жыл бұрын
Glad it helped
@celestigon-8901
3 жыл бұрын
@@PYR-Auto w
It worked !!!Thank you so much! You saved me a lot of money from the dealership
@PYR-Auto
9 ай бұрын
You're Welcome!
Was so easy to program new fob for my Malibu. Thank you for video
@PYR-Auto
3 ай бұрын
You're Welcome! Glad it helped!
Thank you sir! A hiccup at the start for me, but afterwards, worked like a charm! My display lit up on its own at every 10 minutes of the timed parts, too. Pretty dang simple.
@PYR-Auto
3 жыл бұрын
You're Welcome! Yes, it really not that difficult just a bit time consuming
I can’t thank you enough!! I was about to get a panic attack, may all good things come to your life 🌟🙌🏻🙏🏻
@PYR-Auto
3 жыл бұрын
You are very welcome! Glad it helped
Thank you very much , it saves a lot of people money !!
@PYR-Auto
4 жыл бұрын
You're welcome!
@CristianLopez-wq2xs
3 жыл бұрын
So I have to push breik n star...
@CristianLopez-wq2xs
3 жыл бұрын
Or only star
Trying this this weekend, hopefully it works because the dealership wants like $300!
@SRT_Tom
3 жыл бұрын
Did it work?
Все Гуд!Спасибо!🙋♂️
Just saved me $295!!! You are an angel
@PYR-Auto
Жыл бұрын
Glad it helped!
Liked and subscribed as soon as my engine started,, Ever step went well 2017 Chevy Malibu Thank you
@PYR-Auto
3 ай бұрын
You're Welcome! Glad it helped
@Emoney4209
27 күн бұрын
How I got the same car and it’s just stuck on learn key pending
Also, I know the title says up to 2016, but this worked for my 2018 Chevy Malibu fob. 🙏🏼
Great video! Worked for me. Thank you for helping us out 😊
@PYR-Auto
3 ай бұрын
You're Welcome! Glad it helped
Saved me so much money you amazing man
@PYR-Auto
Жыл бұрын
Glad it helped
Tried now my car won’t start 3 tries later I got two keys programmed now thanks bro
Worked Great, Thanks!!
@PYR-Auto
Жыл бұрын
You're Welcome!
Thanks so much this worked for me
@PYR-Auto
9 ай бұрын
You're welcome!
Thanks bro i was running late for work now I’m ok 🙂
@PYR-Auto
Жыл бұрын
Glad it helped!
My brother God bless you bro you just saved my whole morning keep it up God bless you in Jesus name amen
@PYR-Auto
3 жыл бұрын
Thanks, Glad it helped
@malcolmpace6128
3 жыл бұрын
I need help bro this morning i did what u said and drive to work but now im trying to leave work and it says insert new remote press start button please help
@aminjh12
3 жыл бұрын
@@malcolmpace6128 what u did ? I have the same problem also theft system is on
@malcolmpace6128
3 жыл бұрын
@@aminjh12 i just went through the step in the video and programed my old key back to my car cuz som how when i unlocked my car using the key cut my fob got disconnected but i connected it by this short video u good?
@malcolmpace6128
3 жыл бұрын
All u gotta do is hold the start button for 12 second again ...and then hit the brake and start it up like normal
This was so helpful
@PYR-Auto
10 ай бұрын
Glad it helped!
Thanks you very much!
@PYR-Auto
2 жыл бұрын
You're welcome!
Haha I was inspecting a repo at my work that was stuck in fob learning mode and this video saved me!
@PYR-Auto
3 жыл бұрын
Glad it helped!
You’re amazing dude
@PYR-Auto
2 ай бұрын
Glad it helped!
Thank you thank you so much!!!!! 😇
@PYR-Auto
2 жыл бұрын
You’re Welcome!
You're a homie, just got my car back from the body shop and my key was dead. this saved me
@PYR-Auto
5 ай бұрын
Glad it helped
Worked for my 2018 Chevy Malibu LT only thing is when I only did the one new key fob afterwards the service theft deterrent system message came up and the light on so it took me a little bit to go back through but this time I did both my new and old key fob and the message and light went off 👍👍
@PYR-Auto
2 жыл бұрын
Yes a 2018 requires at least 2 keys be successfully programmed or the theft deterrent system is triggered
@yasmincastro3537
Жыл бұрын
Are u suppose to do both keys at the same time cus I’m in the same situation or ?
Hello thanks for the video by the way. All of the buttons work on the key fob, but the dash still says remote not detected and to put key in transmitter pocket I can lock and unlock doors and even the remote start works but the car for some reason still say key not detected. Do you think I should do it over again?
Great video, procedure seems simple enough. Got a question for ya - I just bought an '18 Malibu, it came with 1 working fob. So far it seems like there are procedures to follow if you have zero, or two working fobs. I was wondering, is there an option to program a second fob given that I've already got the one working?
@PYR-Auto
4 жыл бұрын
Yes you are correct, in your owners manual your will notice those are the only two options for programming procedures. However, you can use this procedure, you just need to reprogram in your working fob. If you look at the steps in the description box, or your owners manual, you will repeat steps 4-6 for each remote.
Dear Sir, Thank you very much for the information, My question, when we finish from the procedure as you mention in your video, THE REMOT WILL WORK COMPLETLY ? as example i can start engine from the remote, i can lock or unlock the vehicle from remote ?? again thanks for the information provided. God Bless You
@PYR-Auto
3 жыл бұрын
Yes - once programmed the remote should function just as the original did.
First of all Thanks Bro for that video which helped many people but i would like ask you that if I have already one original key and can I add one more like in that way and save my original key one
@PYR-Auto
2 жыл бұрын
Yes and on these years of Malibu if you already have one working key there is actually a shorter procedure you can use to add an additional. We don't have the video for the shorter procedure yet but you can find the text instructions here www.programyourremote.com/classified/malibu-browse-284.aspx
@anargoyushov2202
2 жыл бұрын
@@PYR-Auto thanks guys, I appreciate you for your support 😃
I seen someone's comments on the bottom and we have the same problem. I have a 2018 Malibu with one programmed remote. Would it work to reprogram the programmed key then program the new key?
Will this method work for a 2013 Chevy Malibu? I replaced the key fob case, but using the old cut key, circuit board and battery.
@PYR-Auto
4 жыл бұрын
If your Malibu has push button start, it should work
I can buy a pair glasses that have Bluetooth cameras recording but it cost $200 for a remote thank you for helping us
Do you have a video set of instructions for how to program a new, second remote when you still have one remote? I lost one if our 2 remotes and want to buy a second one but it will need to be programed.
@PYR-Auto
3 жыл бұрын
You can use this procedure - you will just need to re-program your original remote. If you look at the steps in the description box of the video - you need to repeat steps 4-6 for your original remote after the new one is programmed.
Great
@PYR-Auto
3 ай бұрын
Thanks!
If I have one keyfob which step do i follow? I want to get another keyfob from my friend but she only has one fob. Is it required that i get my second Keyfob key cut? Do you recommend any places to buy the keyfob from? Thank you for making this video! Looking forward to your reply.
@PYR-Auto
4 жыл бұрын
If you already have one working fob, you can use this procedure you will just need to re-program in your existing fob after your new fob, as it will be erased during the procedure. If you look at the steps in the description box, or your owners manual, you will repeat steps 4-6 for each remote additional remote after the new remote is programmed. You can just use the mechanical key from your existing fob that is already cut.
Followed the directions for a 2021 Chevy Malibu. Everything works as shown except that after programming the 1st remote, a message appears that it's ready for Remote 2. It will not allow you to reprogram the same remote, and if you don't have another remote, you will need to press the start stop button for 12 seconds again to exit the programming mode.
@PYR-Auto
3 жыл бұрын
Programming a second remote should solve that issue on a 2021
@kimkonami5685
3 жыл бұрын
@@PYR-Auto Hi, I was able to get a much lesser price after market 2nd remote, it worked like a charm! Funny thing is, it then asked for a 3rd remote, so the newer model cars are equipped to program more remotes. However, with this message, it did not insist on programming #3, so once I exited the program, I no longer got the message and everything works beautifully! Thanks so much!
@PYR-Auto
3 жыл бұрын
Great! Gad you got it fixed. You can actually have up to 8 remotes programmed to the vehicle.
@adilsonalfama2290
3 жыл бұрын
At first you add just one key, exit programmed mode and work??
@kimkonami5685
3 жыл бұрын
@@adilsonalfama2290 Yes, the car asks for the 2nd key every time you start it, just have to exit program mode to start the car. Bit of a pain, so got an after market fob for $25 and it all worked out.
I did all the steps. I wanted to know after it says ready for key #1 and you put the fob in the pocket. How long does it take to learn the fob?
@PYR-Auto
4 жыл бұрын
After you put the remote in the pocket and press the stop/start button, it should happen pretty much right away
I had 2 keys broke one what are my options? Im just looking to replace the one i broke not looking to go to the dealer to spend $300 Thanks in advance.
Hey, I am looking into adding an additional one but the part I’m getting stuck on is, does the new emergency key need to be cut differently than the original one I have or do I get it cut the same as the current one?
@PYR-Auto
3 жыл бұрын
It will be cut the same as your original emergency key
@anthonyspencer7823
3 жыл бұрын
Program Your Remote, sweet thanks so much!
Cadillac XTS 2015 I need my car lock by itself. Thanks so much
Will this work if you're only needing to program (1) remote? We already have (1) working remote. We just need another. Thank you.
@PYR-Auto
2 жыл бұрын
Yes. You just need to reprogram your original remote during the procedure as it will be erased. If you look at the steps in the description box of the video - you need to repeats steps 4-6 for your original remote after the new one is programmed.
Hi, i have 2018 malibu. the battery ran down. after replacement the immo is on the instrument cluster. whats the best way to relearn or reset the immo?
Can I use a FOB from a different vehicle to reprogram for my 2017 Chevy? It is the same. For some reason I received 3 Fobs with my new Equinox. I’ve lost my Fob for my Malibu.
@PYR-Auto
3 жыл бұрын
No - these fobs lock to a vehicle once programmed and have to be "flashed" by someone with the correct equipment before they can be programmed again
Thanks for the video, how does someone get a key cut for that car, do I just walk into the dealership?
@PYR-Auto
Жыл бұрын
yes - go the parts department. You will usually need ID and car registration
Do we need to do the first few steps if we already have a key. We just want to make a spare?
@PYR-Auto
3 жыл бұрын
It depends on the year of your Malibu, some only require 1 working to use the shorter add a key procedure but others require 2 working in order to be able to use the shorter procedure. You can check your year here www.programyourremote.com/classified/malibu-browse-284.aspx
Hello I'm currently trying to program my key fob day 2. I followed the steps before but I'm guessing I didn't give myself enough time yesterday prior to watching your video. So today it's saying Use transmitter pocket to start. Help? Or do I have to start to all over again?
@PYR-Auto
4 жыл бұрын
Hello... I would try just starting over from the beginning.
@cliffhogge3355
4 жыл бұрын
Did u get any replay?
Hi I have a 2016 Chevy Malibu. I have one key fob and the other was stolen by an ex..can I reprogram my key fob using these steps so that the other key fob will no longer work?
@PYR-Auto
4 жыл бұрын
Yes, this procedure will erase any fobs previously programmed to the vehicle.
I had a 2019 Traverse that I traded for a 2017 Malibu. The Malibu had only 1 fob so we kept 1 of the Traverse key fobs hoping to reprogram it. I can get the original fob to program with this process but it doesn’t seem to work on the Traverse fob as a 2nd one. Are they compatible?
@PYR-Auto
3 жыл бұрын
These fobs lock to a vehicle once they are programmed and have to be flashed by someone with the correct equipment before they can be used again
Question My dash isn’t quite the same. I get the messages in this process, but I’m asked if I want to dismiss. I assume that I leave that message up and push the start button anyway?
@PYR-Auto
Жыл бұрын
yes
I still have one of my key fobs, why is the procedure only if you’ve lost both? What should I do so I can program a spare since I still have one?
@PYR-Auto
4 жыл бұрын
It depends on the year of your Malibu. Some years require one working remote to add a new one yourself, some years require two working remotes to be able to add a third yourself. You can check out your year here www.programyourremote.com/classified/malibu-browse-284.aspx
Hello! By doing this will this delete my other remote? I want to program an extra remote and want to make sure that this won’t delete my other programmed one
@PYR-Auto
3 жыл бұрын
It will erase it but you can re-program it during the procedure. If you look at the steps in the description box of the video - you need to repeat steps 4-6 for your original remote after the new one is programmed
If i only have a 4 button remote but bought a 5 button one will this work? Or do i need the dealership to add anything?
@PYR-Auto
3 жыл бұрын
The remote needs to match the vehicles options. If you bought a remote with remote start then the dealership would need to add remote start in order for it to work.
I have a 2016 Chevy malibu stick for n theft deterrent. Can u plz help
Hy thanks for your time. Can you use a used one again? Thanks
@PYR-Auto
3 жыл бұрын
No - unless it has been unlocked or "flashed" by someone with the correct equipment. The remote fobs lock to a vehicle once programmed.
Ok so I’m having a problem I have a 2018 chevy malibu lt and I came across your video after my battery was changed in my key fob. But the problem I’m having is that I only have one keyless entry fob and my dealership doesn’t have another one I’ve programmed one key but it’s saying program key #2 but I don’t have another key is there a way I could just program one key and call it a day?
@PYR-Auto
Жыл бұрын
No - on a 2018 you will need to program a second fob in order to fully exit programming mode
I have a 2016 Malibu and I have non remote start remotes for it. Can I do this process with my new remotes with the remote start function?
@PYR-Auto
Жыл бұрын
No - the key fobs need to match your vehicles options
If I lost my remote but still have the actual key, the one you pull out, will this still work? I was going to order a remote that comes with an uncut key but I still have my cut key and was going to just put my cut key in the new fob. Any ideas if it will work? I see that's a Cadillac. Will the slot in the center console be there? Or would it be somewhere else on a Malibu?
@PYR-Auto
3 жыл бұрын
Yes, you can use the emergency key out of an old remote. The transmitter pocket may look a bit different depending on the year of your Malibu. On most years, you can find this procedure listed in your owners manual under the keys section and it shows a small picture of the transmitter pocket
@donovanblair176
3 жыл бұрын
I figured it out man. You're a life saver. One last question and I'll be done. I wasn't able to find the spare key. I ordered a brand new one and did these steps. When/if I find the key, can I do the process all over again? Like will the same key work being programmed twice?
@PYR-Auto
3 жыл бұрын
This procedure erases all previous remotes but if you ever find the spare again you can re-program it. You can use this procedure to program multiple remotes or, depending on the year of your Malibu, there may be a shorter procedure you can use to add remotes if you already have one working one. You can check that here www.programyourremote.com/classified/malibu-browse-284.aspx
@mlswjs
3 жыл бұрын
Just wanted to confirm - I can use the old key and don’t need to get the key cut on my new replacement fob that I am trying to program ? Because I am Having trouble finding anyone to cut this style of key
I have tried reprogramming my 2 original fobs but cant seem to to them to program. I get to the last step of putting it in trasmitter pocket , press start 1 time and then it does nothing else. Can you help?
@anheiredmond615
2 ай бұрын
Having the exact same issue did you ever find a solution?
Hello I need help with my chevy Malibu 2012 (V300) EU version. I have only 1 Recognized transmitter (smartkey, keyless). How Can I program another one ? I put Recognized transmitter into transmitter pocket and then I put new key into key lock cylinder and turn 5 times to left(unlock) but nothing happened on DIC. Thanks for help
@PYR-Auto
3 жыл бұрын
These instructions are only for vehicles built for the U.S. market. Unfortunately I do not have the programming information for vehicles built for use outside of the U.S.
I can do it with two keys. is that I want to have one to carry it around. and another as a copy if I lose the first one.
@PYR-Auto
3 жыл бұрын
Yes you can do this with multiple remotes. If you look at the steps in the description box of the video - you need to repeat steps 4-6 for the second remote after the first remote is programmed.
I have 2017 Chevy Malibu I did all the steps but the other key was deleted from the system and theft thing came on but it does start and run with the new key any advice?
@PYR-Auto
3 жыл бұрын
With this procedure, you need to re-program any existing remotes during the procedure. If you look at the steps in the description box of the video - you need to repeat steps 4-6 for the working key after the "new" key is programmed.
This is the owner of Chevy Malibu in 2019. I bought a compatible key because I lost one of the two keys. And when I set the key, Q 1> it recognizes it as number 3. Is there a way to set this key to 1 or 2? Q2> The door open close button works normally, but the trunk open/close and horn buttons are switched, is there a way to solve this?
I have a 2017 Malibu, will I need two keys to pair for auto theft system to turn off?
@PYR-Auto
Жыл бұрын
Yes
My key fob went out I replaced the battery as well and still won’t work for my car I haven’t tried this though does it work the same way ?
@PYR-Auto
3 жыл бұрын
Your key fob should not need to be re-programmed after replacing the battery so you may have other issues
I have a 2017 Chevy Malibu. I only had one key and fob and I lost it. I have another set coming, will it program okay or do I need a second?
@PYR-Auto
2 жыл бұрын
You need to program in at least 2 remotes total
@kristicassidy1347
2 жыл бұрын
@@PYR-Auto Okay. I got my fob programmed. It works, turns the car off and on, locks and unlocks. Essentially it works like normal. With that being said my dash shows the “service theft deterrent system” . My question is, is it safe to drive in the meantime while I wait for my second fob to get here? Thanks for your help.
@kristicassidy1347
2 жыл бұрын
@@PYR-Auto Cancel that Lmao. I let it sit and went back out to check on it and it won’t start and the dash prompted “ready for remote 2”.
Hello. Pls help me What if i dont have a manual key of vehicle? Coz i lost it already and i want buy a new fob key and reprogram it
Hello, what do you think the issue is if when I turn the key 5 times, my car is unresponsive entirely? The dash is off no matter what
@PYR-Auto
2 жыл бұрын
Some vehicle only show the message for a few seconds right when the door is opened. You might try just continuing with the procedure on just go off of the time.
If my original fob doesnt have remote start, could i just buy a fob with remote start and program it like this?
@PYR-Auto
Жыл бұрын
No - the fob need to match your vehicles options
Do I need to put the actual key back in the fob or does that not matter??
@PYR-Auto
3 жыл бұрын
It wont matter either way for programming.
Can you do the same procedure if you need to program a second key?
@PYR-Auto
Жыл бұрын
you can - you just need to reprogram your original remote during the procedure as it will be erased. If you look at the steps in the description box of the video, you need to repeat steps 4-6 for your original remote after the new one is programmed
why would it be necessary to have NO remaining smart keys. I have one that works fine, but purchased a new one as a backup or for my wife. Can't i just program/reprogram both keys??? Also is it necessary to cut the key before programming as apposed to after?
@PYR-Auto
3 жыл бұрын
This procedure is for when you loose all keys - depending on the year of your Impala you there may be a shorter procedure to just add a key but you can use this procedure. You just need to re-program your existing remote as it will be erased during the procedure. If look at the steps in the description box of the video, you need to repeat steps 4-6 for your existing remote after the new remote is programmed.
@aminjh12
3 жыл бұрын
@@PYR-Auto so I made mistake . Which i tried to program new key as back up now both are not working but the new one can lock and unlock the door . With message showing remote 2 ready to learn and can’t start the car and can’t even start the process from the beginning. What should I do ?
very good, thank you, one issue is that the trunk button is not responding, God bless you
@PYR-Auto
Жыл бұрын
This whole remote should program in at the same time so there may just be an issue with that button on the fob or the trunk release itself
When performence the steps, my original keyfob was deleted from memory and the new key doesn't programmed and the process still show pendent. When i open the door with my emergency key the message appear on dasboard "add remote 1" and put new remote in transmitter pocket and press star/ stop nothing happen. Any suggestions? scanned i find this code B3031:00 and B3105:00
@PYR-Auto
3 жыл бұрын
They original key fob will need to be reprogrammed during the procedure. If you look at the steps in the description box of the video - you need to repeat steps 4-6 for your original remote after the new one. If the vehicle shows ready for "remote 1" but does not respond to the remote - there may be an issue with the remote you are trying to use. I would try programming the original remote as Remote 1 to determine that.
Instead of getting a new key cut, could I use the old one but for programming the new
@PYR-Auto
5 ай бұрын
yes
Did it work for Any body with a 2017 Malibu ?
@anheiredmond615
2 ай бұрын
Its not working for me
What can be done if both my keys have been un programed but I’m still able to turn on my car and I don’t have a theft light on
@PYR-Auto
2 жыл бұрын
If you're still able to start the car then it sounds like the key or keys are still programmed.
Hi dear is it the same procedure for chevy 2014 cruze ltz?
@PYR-Auto
4 жыл бұрын
A 2014 Cruze should use a Flip-Key. You can find that procedure here www.programyourremote.com/classified/2014-chevrolet-cruze-keyless-entry-remote-key-fob-programming-instructions-listing-7475.aspx
@aliounedia5658
4 жыл бұрын
Thank you 😊
That will work for a 2016 Chevy Malibu LT
Can I use my original cut key and stick it in my new fob I bought? , I washed my original fob and it has been letting off the sirens constantly. If anyone knows please let me know I just bought another fob and want to program it asap.
@PYR-Auto
2 жыл бұрын
Yes - you can use your original emergency key
I'm trying to program the second control but I m not sure witch is the next step
@PYR-Auto
4 жыл бұрын
If you look at the steps in the description box for the video, or in your owners manual, you repeat steps 4-6 for each additional remote.
Soooo since thats a Cadillac does this actually work the same way for the malibu
@PYR-Auto
Ай бұрын
yes - this same procedure works on many different GM models
Would this work for a 2017 Malibu key fob?
@PYR-Auto
2 жыл бұрын
it will but on a 2017 you have to program at least 2 fobs total.
I see you’re working on a Cadillac. Will this work for any vehicle?
@PYR-Auto
Жыл бұрын
not just any vehicle but many GM vehicles that have a push button start ignition use this same procedure
Is there any reason you can’t use this procedure if you still have one working remote and the second remote has failed?
@PYR-Auto
Жыл бұрын
no - not on these years
Hi, I have a 2016 Malibu and I noticed that your video was a Cadillac... Turning the key 5times did nothing for me... I am in Ottawa, Ontario, Canada... Is this why it does not work??? Bob
@PYR-Auto
2 жыл бұрын
It is a Cadillac in the video - the same procedure works on many different GM models. Unfortunately this procedure only works on vehicles built for the U.S. market.
Ive got a 2016 Malibu and although the five turn sequence enters programming mode, the dash won’t light up with the door opening and closing and I’m rather lost. A little help?
@PYR-Auto
4 жыл бұрын
Are you able to see the very first message "REMOTE LEARN PENDING,PLEASE WAIT" on the dash after turning the key 5 times? Also, your Malibu has push button start, correct?
@aaronsmith5264
4 жыл бұрын
@@PYR-Auto yes, it is push start, yes, the message shows up. Then I wait ten minutes and get back in, no message. I push the start stop button and it says remote learn pending, please wait
@aaronsmith5264
4 жыл бұрын
By way of update: I pressed start/stop and it said "ready for remote 1" so I put the remote in the pocket in the center console and pushed stop/start. Then it immediately said "ready for remote 2" so I did the same procedure. Then it asked for remote 3 at which point I held down the start stop button until the dash shut off. Neither remote works.
@PYR-Auto
4 жыл бұрын
@@aaronsmith5264 You are getting the vehicle into programming mode so I would suggest just continuing with the procedure and watch your times rather than the dash. It is supposed to say remote learn pending please wait each time until after the third 10 minute mark.
Will this work on a 2020 malibu, the key pocket is at the back of the console i believe
@PYR-Auto
Жыл бұрын
a 2020 Malibu is the same procedure but requires that at least 2 remotes be programmed during the procedure ( including any that already work for the vehicle and need to be reprogrammed )
@BrandonCartwright04
Жыл бұрын
@@PYR-Auto thank you very much. I thought so but wasnt sure
@PYR-Auto
Жыл бұрын
You're Welcome!
Where the key transmitter in a chevy malibu where you put the key in the glove compartment
@PYR-Auto
3 жыл бұрын
What year Chevy Malibu?
@benzobankze5522
3 жыл бұрын
@@PYR-Auto 2019
@PYR-Auto
3 жыл бұрын
@@benzobankze5522 on a 2019 Malibu the smart key will go in the center console, like the video shows, however your transmitter pocket will be at the back of the center console instead of the front. If you still can't find it, there is a diagram of the location shown in your owners manual.
What do I do if after doing this it only works when I leave the remote in the transmitter pocket?? I’ve reset the battery and tried it again and again I even went a bought a new one cause the old one wasn’t picking up completely wouldn’t even lock or unlock.
@PYR-Auto
3 жыл бұрын
Since you already replaced the battery on the fob - there may just be an issue with fob itself. If the same this is happening with multiple remotes then there could be an issue with the vehicle.
@elizavettalavera157
3 жыл бұрын
The same thing happened to me. Car only turns on when I have the key fob in the transmitter pocket. Remote buttons don't work, can't unlock/lock or open trunk.
@cannonballseven
Жыл бұрын
Same
I have 2019 my car doesn't have the push start button my push start button on the key fob